T30 requires specific SDMMC pad programming, and bus power-rail bringup.
Signed-off-by: Tom Warren twarren@nvidia.com --- v2: - rewrite pad_init_mmc to use mmc_id instead of SDMMC base address - add PMU-specific comments to board_sdmmc_voltage_init sequence v3: - removed GP_SDIOCFG writes, now done during pinmux init via table
board/nvidia/cardhu/cardhu.c | 51 ++++++++++++++++++++++++++++++++++++++++++ board/nvidia/common/board.c | 31 ++++++++++++++++++++++++- 2 files changed, 81 insertions(+), 1 deletions(-)
diff --git a/board/nvidia/cardhu/cardhu.c b/board/nvidia/cardhu/cardhu.c index 08e9b7b..3544b41 100644 --- a/board/nvidia/cardhu/cardhu.c +++ b/board/nvidia/cardhu/cardhu.c @@ -25,6 +25,10 @@ #include <asm/arch/pinmux.h> #include <asm/arch/gp_padctrl.h> #include "pinmux-config-cardhu.h" +#include <i2c.h> + +#define PMU_I2C_ADDRESS 0x2D +#define MAX_I2C_RETRY 3
/* * Routine: pinmux_init @@ -41,3 +45,50 @@ void pinmux_init(void) /* Initialize any non-default pad configs (APB_MISC_GP regs) */ padgrp_config_table(cardhu_padctrl, ARRAY_SIZE(cardhu_padctrl)); } + +#if defined(CONFIG_TEGRA_MMC) +/* + * Do I2C/PMU writes to bring up SD card bus power + * + */ +void board_sdmmc_voltage_init(void) +{ + uchar reg, data_buffer[1]; + int i; + + i2c_set_bus_num(0); /* PMU is on bus 0 */ + + /* TPS659110: LDO5_REG = 3.3v, ACTIVE to SDMMC1 */ + data_buffer[0] = 0x65; + reg = 0x32; + + for (i = 0; i < MAX_I2C_RETRY; ++i) { + if (i2c_write(PMU_I2C_ADDRESS, reg, 1, data_buffer, 1)) + udelay(100); + } + + /* TPS659110: GPIO7_REG = PDEN, output a 1 to EN_3V3_SYS */ + data_buffer[0] = 0x09; + reg = 0x67; + + for (i = 0; i < MAX_I2C_RETRY; ++i) { + if (i2c_write(PMU_I2C_ADDRESS, reg, 1, data_buffer, 1)) + udelay(100); + } +} + +/* + * Routine: pin_mux_mmc + * Description: setup the MMC muxes, power rails, etc. + */ +void pin_mux_mmc(void) +{ + /* + * NOTE: We don't do mmc-specific pin muxes here. + * They were done globally in pinmux_init(). + */ + + /* Bring up the SDIO1 power rail */ + board_sdmmc_voltage_init(); +} +#endif /* MMC */ diff --git a/board/nvidia/common/board.c b/board/nvidia/common/board.c index babbe08..7d9f361 100644 --- a/board/nvidia/common/board.c +++ b/board/nvidia/common/board.c @@ -49,6 +49,7 @@ #include <asm/arch-tegra/usb.h> #endif #ifdef CONFIG_TEGRA_MMC +#include <asm/arch-tegra/tegra_mmc.h> #include <asm/arch-tegra/mmc.h> #endif #include <i2c.h> @@ -245,4 +246,32 @@ int board_mmc_init(bd_t *bd)
return 0; } -#endif + +void pad_init_mmc(struct mmc_host *host) +{ +#if defined(CONFIG_TEGRA30) + enum periph_id id = host->mmc_id; + u32 val; + + debug("%s: sdmmc address = %08x, id = %d\n", __func__, + (unsigned int)host->reg, id); + + /* Set the pad drive strength for SDMMC1 or 3 only */ + if (id != PERIPH_ID_SDMMC1 && id != PERIPH_ID_SDMMC3) { + debug("%s: settings are only valid for SDMMC1/SDMMC3!\n", + __func__); + return; + } + + val = readl(&host->reg->sdmemcmppadctl); + val &= 0xFFFFFFF0; + val |= MEMCOMP_PADCTRL_VREF; + writel(val, &host->reg->sdmemcmppadctl); + + val = readl(&host->reg->autocalcfg); + val &= 0xFFFF0000; + val |= AUTO_CAL_PU_OFFSET | AUTO_CAL_PD_OFFSET | AUTO_CAL_ENABLED; + writel(val, &host->reg->autocalcfg); +#endif /* T30 */ +} +#endif /* MMC */