Sync rk3399-gru related device tree from Linux kernel v6.8.
The spi_flash symbol is no longer part of upstream DT, it is re-defined to allow existing reference use in related u-boot.dtsi-files.
Signed-off-by: Jonas Karlman jonas@kwiboo.se Reviewed-by: Kever Yang kever.yang@rock-chips.com --- v2: Collect r-b tag
The spi_flash node should probably use bootph pre-ram/some-ram instead of all to match other boards. I cannot test so it is kept as-is. --- arch/arm/dts/rk3399-gru-bob.dts | 8 +- arch/arm/dts/rk3399-gru-chromebook.dtsi | 200 +++++++++++++++++++++++- arch/arm/dts/rk3399-gru-kevin.dts | 3 +- arch/arm/dts/rk3399-gru-u-boot.dtsi | 10 +- arch/arm/dts/rk3399-gru.dtsi | 52 +++++- 5 files changed, 254 insertions(+), 19 deletions(-)
diff --git a/arch/arm/dts/rk3399-gru-bob.dts b/arch/arm/dts/rk3399-gru-bob.dts index e6c1c94c8d69..1cba1d857c96 100644 --- a/arch/arm/dts/rk3399-gru-bob.dts +++ b/arch/arm/dts/rk3399-gru-bob.dts @@ -16,6 +16,7 @@ "google,bob-rev7", "google,bob-rev6", "google,bob-rev5", "google,bob-rev4", "google,bob", "google,gru", "rockchip,rk3399"; + chassis-type = "convertible";
edp_panel: edp-panel { compatible = "boe,nv101wxmn51"; @@ -69,7 +70,7 @@ &spi0 { status = "okay";
- cr50@0 { + tpm@0 { compatible = "google,cr50"; reg = <0>; interrupt-parent = <&gpio0>; @@ -87,3 +88,8 @@ }; }; }; + +&wlan_host_wake_l { + /* Kevin has an external pull up, but Bob does not. */ + rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>; +}; diff --git a/arch/arm/dts/rk3399-gru-chromebook.dtsi b/arch/arm/dts/rk3399-gru-chromebook.dtsi index 1384dabbdf40..cacbad35cfc8 100644 --- a/arch/arm/dts/rk3399-gru-chromebook.dtsi +++ b/arch/arm/dts/rk3399-gru-chromebook.dtsi @@ -198,7 +198,6 @@ power-supply = <&pp3300_disp>; pinctrl-names = "default"; pinctrl-0 = <&bl_en>; - pwm-delay-us = <10000>; };
gpio_keys: gpio-keys { @@ -206,7 +205,7 @@ pinctrl-names = "default"; pinctrl-0 = <&bt_host_wake_l>;
- wake_on_bt: wake-on-bt { + wake_on_bt: key-wake-on-bt { label = "Wake-on-Bluetooth"; gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; linux,code = <KEY_WAKEUP>; @@ -234,9 +233,24 @@ extcon = <&usbc_extcon0>, <&usbc_extcon1>; };
+&dmc { + center-supply = <&ppvar_centerlogic>; + rockchip,pd-idle-dis-freq-hz = <800000000>; + rockchip,sr-idle-dis-freq-hz = <800000000>; + rockchip,sr-mc-gate-idle-dis-freq-hz = <800000000>; +}; + &edp { status = "okay";
+ /* + * eDP PHY/clk don't sync reliably at anything other than 24 MHz. Only + * set this here, because rk3399-gru.dtsi ensures we can generate this + * off GPLL=600MHz, whereas some other RK3399 boards may not. + */ + assigned-clocks = <&cru PCLK_EDP>; + assigned-clock-rates = <24000000>; + ports { edp_out: port@1 { reg = <1>; @@ -251,6 +265,182 @@ }; };
+&gpio0 { + gpio-line-names = /* GPIO0 A 0-7 */ + "AP_RTC_CLK_IN", + "EC_AP_INT_L", + "PP1800_AUDIO_EN", + "BT_HOST_WAKE_L", + "WLAN_MODULE_PD_L", + "H1_INT_OD_L", + "CENTERLOGIC_DVS_PWM", + "", + + /* GPIO0 B 0-4 */ + "WIFI_HOST_WAKE_L", + "PMUIO2_33_18_L", + "PP1500_EN", + "AP_EC_WARM_RESET_REQ", + "PP3000_EN"; +}; + +&gpio1 { + gpio-line-names = /* GPIO1 A 0-7 */ + "", + "", + "SPK_PA_EN", + "", + "TRACKPAD_INT_L", + "AP_EC_S3_S0_L", + "AP_EC_OVERTEMP", + "AP_SPI_FLASH_MISO", + + /* GPIO1 B 0-7 */ + "AP_SPI_FLASH_MOSI_R", + "AP_SPI_FLASH_CLK_R", + "AP_SPI_FLASH_CS_L_R", + "WLAN_MODULE_RESET_L", + "WIFI_DISABLE_L", + "MIC_INT", + "", + "AP_I2C_DVS_SDA", + + /* GPIO1 C 0-7 */ + "AP_I2C_DVS_SCL", + "AP_BL_EN", + /* + * AP_FLASH_WP is crossystem ABI. Schematics call it + * AP_FW_WP or CPU1_FW_WP, depending on the variant. + */ + "AP_FLASH_WP", + "LITCPU_DVS_PWM", + "AP_I2C_AUDIO_SDA", + "AP_I2C_AUDIO_SCL", + "", + "HEADSET_INT_L"; +}; + +&gpio2 { + gpio-line-names = /* GPIO2 A 0-7 */ + "", + "", + "SD_IO_PWR_EN", + "", + "", + "", + "", + "", + + /* GPIO2 B 0-7 */ + "", + "", + "", + "", + "", + "", + "", + "", + + /* GPIO2 C 0-7 */ + "", + "", + "", + "", + "AP_SPI_EC_MISO", + "AP_SPI_EC_MOSI", + "AP_SPI_EC_CLK", + "AP_SPI_EC_CS_L", + + /* GPIO2 D 0-4 */ + "BT_DEV_WAKE_L", + "", + "WIFI_PCIE_CLKREQ_L", + "WIFI_PERST_L", + "SD_PWR_3000_1800_L"; +}; + +&gpio3 { + gpio-line-names = /* GPIO3 A 0-7 */ + "", + "", + "", + "", + "AP_SPI_TPM_MISO", + "AP_SPI_TPM_MOSI_R", + "AP_SPI_TPM_CLK_R", + "AP_SPI_TPM_CS_L_R", + + /* GPIO3 B 0-7 */ + "EC_IN_RW", + "", + "AP_I2C_TP_SDA", + "AP_I2C_TP_SCL", + "AP_I2C_TP_PU_EN", + "TOUCH_INT_L", + "", + "", + + /* GPIO3 C 0-7 */ + "", + "", + "", + "", + "", + "", + "", + "", + + /* GPIO3 D 0-7 */ + "I2S0_SCLK", + "I2S0_LRCK_RX", + "I2S0_LRCK_TX", + "I2S0_SDI_0", + "I2S0_SDI_1", + "", + "I2S0_SDO_1", + "I2S0_SDO_0"; +}; + +&gpio4 { + gpio-line-names = /* GPIO4 A 0-7 */ + "I2S_MCLK", + "AP_I2C_MIC_SDA", + "AP_I2C_MIC_SCL", + "", + "", + "", + "", + "", + + /* GPIO4 B 0-7 */ + "", + "", + "", + "", + "", + "", + "", + "", + + /* GPIO4 C 0-7 */ + "AP_I2C_TS_SDA", + "AP_I2C_TS_SCL", + "GPU_DVS_PWM", + "UART_DBG_TX_AP_RX", + "UART_AP_TX_DBG_RX", + "", + "BIGCPU_DVS_PWM", + "EDP_HPD_3V0", + + /* GPIO4 D 0-5 */ + "SD_CARD_DET_L", + "USB_DP_HPD", + "TOUCH_RESET_L", + "PP3300_DISP_EN", + "", + "SD_SLOT_PWR_EN"; +}; + ap_i2c_mic: &i2c1 { status = "okay";
@@ -286,7 +476,7 @@ ap_i2c_tp: &i2c5 { };
&cros_ec { - cros_ec_pwm: ec-pwm { + cros_ec_pwm: pwm { compatible = "google,cros-ec-pwm"; #pwm-cells = <1>; }; @@ -319,8 +509,7 @@ ap_i2c_tp: &i2c5 { &pci_rootport { mvl_wifi: wifi@0,0 { compatible = "pci1b4b,2b42"; - reg = <0x83010000 0x0 0x00000000 0x0 0x00100000 - 0x83010000 0x0 0x00100000 0x0 0x00100000>; + reg = <0x0000 0x0 0x0 0x0 0x0>; interrupt-parent = <&gpio0>; interrupts = <8 IRQ_TYPE_LEVEL_LOW>; pinctrl-names = "default"; @@ -395,6 +584,7 @@ ap_i2c_tp: &i2c5 { };
wlan_host_wake_l: wlan-host-wake-l { + /* Kevin has an external pull up, but Bob does not */ rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>; }; }; diff --git a/arch/arm/dts/rk3399-gru-kevin.dts b/arch/arm/dts/rk3399-gru-kevin.dts index 2bbef9fcbe27..2cc9b3386c16 100644 --- a/arch/arm/dts/rk3399-gru-kevin.dts +++ b/arch/arm/dts/rk3399-gru-kevin.dts @@ -24,6 +24,7 @@ "google,kevin-rev9", "google,kevin-rev8", "google,kevin-rev7", "google,kevin-rev6", "google,kevin", "google,gru", "rockchip,rk3399"; + chassis-type = "convertible";
/* Power tree */
@@ -91,7 +92,7 @@ pinctrl-names = "default"; pinctrl-0 = <&bt_host_wake_l>, <&cpu1_pen_eject>;
- pen-insert { + switch-pen-insert { label = "Pen Insert"; /* Insert = low, eject = high */ gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; diff --git a/arch/arm/dts/rk3399-gru-u-boot.dtsi b/arch/arm/dts/rk3399-gru-u-boot.dtsi index 0cc40eb6d6f6..6bdc892bd913 100644 --- a/arch/arm/dts/rk3399-gru-u-boot.dtsi +++ b/arch/arm/dts/rk3399-gru-u-boot.dtsi @@ -78,12 +78,14 @@ /delete-property/ bootph-pre-ram; };
+&spi1 { + spi_flash: flash@0 { + bootph-all; + }; +}; + &spi5 { spi-activate-delay = <100>; spi-max-frequency = <3000000>; spi-deactivate-delay = <200>; }; - -&spi_flash { - bootph-all; -}; diff --git a/arch/arm/dts/rk3399-gru.dtsi b/arch/arm/dts/rk3399-gru.dtsi index b80f19066b57..d90fe4d40d48 100644 --- a/arch/arm/dts/rk3399-gru.dtsi +++ b/arch/arm/dts/rk3399-gru.dtsi @@ -250,7 +250,7 @@ pinctrl-0 = <&sd_io_pwr_en &sd_pwr_1800_sel>;
enable-active-high; - enable-gpio = <&gpio2 2 GPIO_ACTIVE_HIGH>; + enable-gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>; gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>; states = <1800000 0x1>, <3000000 0x0>; @@ -286,7 +286,7 @@
sound: sound { compatible = "rockchip,rk3399-gru-sound"; - rockchip,cpu = <&i2s0 &i2s2>; + rockchip,cpu = <&i2s0 &spdif>; }; };
@@ -373,6 +373,34 @@ <200000000>; };
+&dfi { + status = "okay"; +}; + +&dmc { + status = "okay"; + + rockchip,pd-idle-ns = <160>; + rockchip,sr-idle-ns = <10240>; + rockchip,sr-mc-gate-idle-ns = <40960>; + rockchip,srpd-lite-idle-ns = <61440>; + rockchip,standby-idle-ns = <81920>; + + rockchip,ddr3_odt_dis_freq = <666000000>; + rockchip,lpddr3_odt_dis_freq = <666000000>; + rockchip,lpddr4_odt_dis_freq = <666000000>; + + rockchip,sr-mc-gate-idle-dis-freq-hz = <1000000000>; + rockchip,srpd-lite-idle-dis-freq-hz = <0>; + rockchip,standby-idle-dis-freq-hz = <928000000>; +}; + +&dmc_opp_table { + opp03 { + opp-suspend; + }; +}; + &emmc_phy { status = "okay"; }; @@ -437,10 +465,6 @@ ap_i2c_audio: &i2c8 { status = "okay"; };
-&i2s2 { - status = "okay"; -}; - &io_domains { status = "okay";
@@ -461,10 +485,11 @@ ap_i2c_audio: &i2c8 { vpcie0v9-supply = <&pp900_pcie>;
pci_rootport: pcie@0,0 { - reg = <0x83000000 0x0 0x00000000 0x0 0x00000000>; + reg = <0x0000 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; ranges; + device_type = "pci"; }; };
@@ -537,13 +562,24 @@ ap_i2c_audio: &i2c8 { vqmmc-supply = <&ppvar_sd_card_io>; };
+&spdif { + status = "okay"; + + /* + * SPDIF is routed internally to DP; we either don't use these pins, or + * mux them to something else. + */ + /delete-property/ pinctrl-0; + /delete-property/ pinctrl-names; +}; + &spi1 { status = "okay";
pinctrl-names = "default", "sleep"; pinctrl-1 = <&spi1_sleep>;
- spi_flash: spiflash@0 { + flash@0 { compatible = "jedec,spi-nor"; reg = <0>;