enable DTS support for keymile mpc83xx based boards.
get rid of compile warning: ===================== WARNING ====================== This board does not use CONFIG_DM_ETH (Driver Model for Ethernet drivers). Please update the board to use CONFIG_DM_ETH before the v2020.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ====================================================
Therefore done: - add DTS for all mpc83xx based boards from keymile mainly they are not mainlined to linux. - add u-boot specific dtsi - add stdout-path - add missing ucc4 par_io definitions, which were in board code, but not in linux DTS - remove not used ethernet nodes
Signed-off-by: Heiko Schocher hs@denx.de
---
Changes in v2: - add patch which fixes Codingstyle errors in drivers/qe - add patch which converts the mpc83xx based boards from keymile to DM_ETH
arch/powerpc/cpu/mpc83xx/Kconfig | 8 + arch/powerpc/dts/Makefile | 8 + arch/powerpc/dts/km8309-uboot.dtsi | 33 ++ arch/powerpc/dts/km8321-uboot.dtsi | 67 ++++ arch/powerpc/dts/km8321.dtsi | 220 ++++++++++++ arch/powerpc/dts/km836x-uboot.dtsi | 61 ++++ arch/powerpc/dts/km836x.dtsi | 182 ++++++++++ arch/powerpc/dts/kmcoge5ne-uboot.dtsi | 22 ++ arch/powerpc/dts/kmcoge5ne.dts | 320 +++++++++++++++++ arch/powerpc/dts/kmeter1-uboot.dtsi | 42 +++ arch/powerpc/dts/kmeter1.dts | 480 ++++++++++++++++++++++++++ arch/powerpc/dts/kmopti2.dts | 161 +++++++++ arch/powerpc/dts/kmsupc5.dts | 139 ++++++++ arch/powerpc/dts/kmsupm5.dts | 129 +++++++ arch/powerpc/dts/kmtegr1.dts | 392 +++++++++++++++++++++ arch/powerpc/dts/kmtepr2.dts | 142 ++++++++ arch/powerpc/dts/kmtuge1.dts | 100 ++++++ arch/powerpc/dts/kmtuxa1.dts | 100 ++++++ board/keymile/km83xx/Kconfig | 17 + board/keymile/km83xx/MAINTAINERS | 23 +- board/keymile/km83xx/km83xx.c | 64 ---- configs/kmcoge5ne_defconfig | 11 +- configs/kmeter1_defconfig | 10 +- configs/kmopti2_defconfig | 11 +- configs/kmsupx5_defconfig | 10 +- configs/kmtegr1_defconfig | 12 +- configs/kmtepr2_defconfig | 10 +- configs/tuge1_defconfig | 10 +- configs/tuxx1_defconfig | 11 +- include/configs/km/km-mpc832x.h | 14 - include/configs/km/km-mpc8360.h | 14 - include/configs/km/km-mpc83xx.h | 10 - 32 files changed, 2694 insertions(+), 139 deletions(-) create mode 100644 arch/powerpc/dts/km8309-uboot.dtsi create mode 100644 arch/powerpc/dts/km8321-uboot.dtsi create mode 100644 arch/powerpc/dts/km8321.dtsi create mode 100644 arch/powerpc/dts/km836x-uboot.dtsi create mode 100644 arch/powerpc/dts/km836x.dtsi create mode 100644 arch/powerpc/dts/kmcoge5ne-uboot.dtsi create mode 100644 arch/powerpc/dts/kmcoge5ne.dts create mode 100644 arch/powerpc/dts/kmeter1-uboot.dtsi create mode 100644 arch/powerpc/dts/kmeter1.dts create mode 100644 arch/powerpc/dts/kmopti2.dts create mode 100644 arch/powerpc/dts/kmsupc5.dts create mode 100644 arch/powerpc/dts/kmsupm5.dts create mode 100644 arch/powerpc/dts/kmtegr1.dts create mode 100644 arch/powerpc/dts/kmtepr2.dts create mode 100644 arch/powerpc/dts/kmtuge1.dts create mode 100644 arch/powerpc/dts/kmtuxa1.dts
diff --git a/arch/powerpc/cpu/mpc83xx/Kconfig b/arch/powerpc/cpu/mpc83xx/Kconfig index 18808da37d..2bae08e278 100644 --- a/arch/powerpc/cpu/mpc83xx/Kconfig +++ b/arch/powerpc/cpu/mpc83xx/Kconfig @@ -101,34 +101,42 @@ config TARGET_IDS8313 config TARGET_KMETER1 bool "Support kmeter1" select VENDOR_KM + select KM_ENABLE_FULL_DM_DTS_SUPPORT
config TARGET_KMCOGE5NE bool "Support kmcoge5ne" select VENDOR_KM + select KM_ENABLE_FULL_DM_DTS_SUPPORT
config TARGET_KMTEGR1 bool "Support kmtegr1" select VENDOR_KM + select KM_ENABLE_FULL_DM_DTS_SUPPORT
config TARGET_TUXX1 bool "Support tuxx1" select VENDOR_KM + select KM_ENABLE_FULL_DM_DTS_SUPPORT
config TARGET_KMSUPX5 bool "Support kmsupx5" select VENDOR_KM + select KM_ENABLE_FULL_DM_DTS_SUPPORT
config TARGET_TUGE1 bool "Support tuge1" select VENDOR_KM + select KM_ENABLE_FULL_DM_DTS_SUPPORT
config TARGET_KMOPTI2 bool "Support kmopti2" select VENDOR_KM + select KM_ENABLE_FULL_DM_DTS_SUPPORT
config TARGET_KMTEPR2 bool "Support kmtepr2" select VENDOR_KM + select KM_ENABLE_FULL_DM_DTS_SUPPORT
config TARGET_TQM834X bool "Support TQM834x" diff --git a/arch/powerpc/dts/Makefile b/arch/powerpc/dts/Makefile index 7eb005f450..266d345f72 100644 --- a/arch/powerpc/dts/Makefile +++ b/arch/powerpc/dts/Makefile @@ -1,5 +1,11 @@ # SPDX-License-Identifier: GPL-2.0+
+dtb-$(CONFIG_TARGET_KMCOGE5NE) += kmcoge5ne.dtb +dtb-$(CONFIG_TARGET_KMETER1) += kmeter1.dtb +dtb-$(CONFIG_TARGET_KMOPTI2) += kmopti2.dtb +dtb-$(CONFIG_TARGET_KMSUPX5) += kmsupc5.dtb kmsupm5.dtb +dtb-$(CONFIG_TARGET_KMTEGR1) += kmtegr1.dtb +dtb-$(CONFIG_TARGET_KMTEPR2) += kmtepr2.dtb dtb-$(CONFIG_TARGET_MPC8548CDS) += mpc8548cds.dtb mpc8548cds_36b.dtb dtb-$(CONFIG_TARGET_P1010RDB_PA) += p1010rdb-pa.dtb p1010rdb-pa_36b.dtb dtb-$(CONFIG_TARGET_P1010RDB_PB) += p1010rdb-pb.dtb p1010rdb-pb_36b.dtb @@ -16,6 +22,8 @@ dtb-$(CONFIG_TARGET_T1042D4RDB) += t1042d4rdb.dtb dtb-$(CONFIG_TARGET_T2080QDS) += t2080qds.dtb dtb-$(CONFIG_TARGET_T2080RDB) += t2080rdb.dtb dtb-$(CONFIG_TARGET_T4240RDB) += t4240rdb.dtb +dtb-$(CONFIG_TARGET_TUGE1) += kmtuge1.dtb +dtb-$(CONFIG_TARGET_TUXX1) += kmtuxa1.dtb dtb-$(CONFIG_TARGET_MCR3000) += mcr3000.dtb dtb-$(CONFIG_TARGET_GAZERBEAM) += gazerbeam.dtb
diff --git a/arch/powerpc/dts/km8309-uboot.dtsi b/arch/powerpc/dts/km8309-uboot.dtsi new file mode 100644 index 0000000000..c44ce7d8dc --- /dev/null +++ b/arch/powerpc/dts/km8309-uboot.dtsi @@ -0,0 +1,33 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * ABB PGGA 8309 U-Boot specific Device Tree Source parts + * + * Copyright (C) 2020 Heiko Schocher hs@denx.de + * + */ + +/ { + cpus { + u-boot,dm-pre-reloc; + PowerPC,8309@0 { + u-boot,dm-pre-reloc; + }; + }; + + chosen { + stdout-path = &serial0; + }; +}; + +&qe { + compatible = "fsl,qe", "simple-bus"; +}; + +&soc { + u-boot,dm-pre-reloc; +}; + +&serial0 { + clock-frequency = <132000000>; + u-boot,dm-pre-reloc; +}; diff --git a/arch/powerpc/dts/km8321-uboot.dtsi b/arch/powerpc/dts/km8321-uboot.dtsi new file mode 100644 index 0000000000..348826057a --- /dev/null +++ b/arch/powerpc/dts/km8321-uboot.dtsi @@ -0,0 +1,67 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * ABB PGGA 8321 U-Boot specific Device Tree Source parts + * + * Copyright (C) 2020 Heiko Schocher hs@denx.de + * + */ + +/ { + cpus { + u-boot,dm-pre-reloc; + PowerPC,8321@0 { + u-boot,dm-pre-reloc; + }; + }; + + chosen { + stdout-path = &serial0; + }; +}; + +&enet_piggy2 { + status = "okay"; +}; + +&qe { + compatible = "fsl,qe", "simple-bus"; +}; + +&serial0 { + clock-frequency = <132000000>; + u-boot,dm-pre-reloc; +}; + +&soc { + u-boot,dm-pre-reloc; + + par_io@1400 { + compatible = "fsl,mpc8360-par_io"; + u-boot,dm-pre-reloc; + + serial_pin@0 { + u-boot,dm-pre-reloc; + }; + ucc_pin@0 { + u-boot,dm-pre-reloc; + }; + ucc_pin@1 { + u-boot,dm-pre-reloc; + }; + ucc_pin@3 { + u-boot,dm-pre-reloc; + }; + ucc_pin@4 { + u-boot,dm-pre-reloc; + }; + ucc_pin@5 { + u-boot,dm-pre-reloc; + }; + ucc_pin@6 { + u-boot,dm-pre-reloc; + }; + ucc_pin@7 { + u-boot,dm-pre-reloc; + }; + }; +}; diff --git a/arch/powerpc/dts/km8321.dtsi b/arch/powerpc/dts/km8321.dtsi new file mode 100644 index 0000000000..e49361359d --- /dev/null +++ b/arch/powerpc/dts/km8321.dtsi @@ -0,0 +1,220 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * ABB PGGA km8321 common ports Device Tree Source + * + * Copyright (C) 2020 Heiko Schocher hs@denx.de + * + */ + +/dts-v1/; + +/ { + cpus { + #address-cells = <1>; + #size-cells = <0>; + + PowerPC,8321@0 { + device_type = "cpu"; + reg = <0x0>; + d-cache-line-size = <32>; // 32 bytes + i-cache-line-size = <32>; // 32 bytes + d-cache-size = <16384>; // L1, 16K + i-cache-size = <16384>; // L1, 16K + timebase-frequency = <66000000>; + bus-frequency = <264000000>; + clock-frequency = <528000000>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x10000000>; + }; + + soc: soc8321@e0000000 { + #address-cells = <1>; + #size-cells = <1>; + device_type = "soc"; + compatible = "simple-bus"; + ranges = <0x0 0xe0000000 0x00100000>; + reg = <0xe0000000 0x00000200>; + bus-frequency = <264000000>; + + i2c0: i2c@3000 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + compatible = "fsl,mpc8313-i2c","fsl-i2c"; + reg = <0x3000 0x100>; + interrupts = <14 0x8>; + interrupt-parent = <&ipic>; + clock-frequency = <100000>; + }; + + serial0: serial@4500 { + cell-index = <0>; + device_type = "serial"; + compatible = "fsl,ns16550", "ns16550"; + reg = <0x4500 0x100>; + clock-frequency = <264000000>; + interrupts = <9 0x8>; + interrupt-parent = <&ipic>; + }; + + dma@82a8 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8321-dma", "fsl,elo-dma"; + reg = <0x82a8 4>; + ranges = <0 0x8100 0x1a8>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + cell-index = <0>; + dma-channel@0 { + compatible = "fsl,mpc8321-dma-channel", + "fsl,elo-dma-channel"; + reg = <0 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + dma-channel@80 { + compatible = "fsl,mpc8321-dma-channel", + "fsl,elo-dma-channel"; + reg = <0x80 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + dma-channel@100 { + compatible = "fsl,mpc8321-dma-channel", + "fsl,elo-dma-channel"; + reg = <0x100 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + dma-channel@180 { + compatible = "fsl,mpc8321-dma-channel", + "fsl,elo-dma-channel"; + reg = <0x180 0x28>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + }; + + ipic: pic@700 { + #address-cells = <0>; + #interrupt-cells = <2>; + compatible = "fsl,pq2pro-pic", "fsl,ipic"; + interrupt-controller; + reg = <0x700 0x100>; + device_type = "ipic"; + }; + + par_io: par_io@1400 { + #address-cells = <1>; + #size-cells = <1>; + reg = <0x1400 0x100>; + ranges; + device_type = "par_io"; + num-ports = <7>; + + qe_pio_d: gpio-controller@48 { + #gpio-cells = <2>; + compatible = "fsl,mpc8360-qe-pario-bank", + "fsl,mpc8323-qe-pario-bank"; + reg = <0x1448 0x18>; + gpio-controller; + }; + }; + }; + + qe: qe@e0100000 { + #address-cells = <1>; + #size-cells = <1>; + device_type = "qe"; + compatible = "fsl,qe"; + ranges = <0x0 0xe0100000 0x00100000>; + reg = <0xe0100000 0x480>; + brg-frequency = <0>; + bus-frequency = <396000000>; + + muram@10000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,qe-muram", "fsl,cpm-muram"; + ranges = <0x0 0x00010000 0x00004000>; + + data-only@0 { + compatible = "fsl,qe-muram-data", + "fsl,cpm-muram-data"; + reg = <0x0 0x4000>; + }; + }; + + /* Piggy2 (UCC4, MDIO 0x00, RMII) */ + enet_piggy2: ucc@3200 { + device_type = "network"; + compatible = "ucc_geth"; + cell-index = <4>; + reg = <0x3200 0x200>; + interrupts = <35>; + interrupt-parent = <&qeic>; + local-mac-address = [ 00 00 00 00 00 00 ]; + rx-clock-name = "none"; + tx-clock-name = "clk17"; + phy-handle = <&phy_piggy2>; + phy-connection-type = "rmii"; + pio-handle = <&pio_ucc4>; + }; + + mdio: mdio@3320 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x3320 0x18>; + compatible = "fsl,ucc-mdio"; + + /* Piggy2 (UCC4, MDIO 0x00, RMII) */ + phy_piggy2: ethernet-phy@00 { + reg = <0x0>; + device_type = "ethernet-phy"; + }; + }; + + qeic: interrupt-controller@80 { + interrupt-controller; + compatible = "fsl,qe-ic"; + #address-cells = <0>; + #interrupt-cells = <1>; + reg = <0x80 0x80>; + big-endian; + interrupts = <32 8 33 8>; + interrupt-parent = <&ipic>; + }; + bootcount@0x13ff8 { + device_type = "bootcount"; + compatible = "u-boot,bootcount"; + reg = <0x13ff8 0x08>; + }; + + spi0: spi@4c0 { + cell-index = <0>; + compatible = "fsl,spi"; + reg = <0x4c0 0x40>; + interrupts = <2>; + interrupt-parent = <&qeic>; + mode = "qe"; + #address-cells = <1>; + #size-cells = <0>; + pio-handle = <&pio_spi>; + }; + }; + + localbus: localbus@e0005000 { + #address-cells = <2>; + #size-cells = <1>; + compatible = "fsl,mpc8321-localbus", "fsl,pq2pro-localbus", + "simple-bus"; + reg = <0xe0005000 0xd8>; + }; +}; + +#include "km8321-uboot.dtsi" diff --git a/arch/powerpc/dts/km836x-uboot.dtsi b/arch/powerpc/dts/km836x-uboot.dtsi new file mode 100644 index 0000000000..ac5339eff6 --- /dev/null +++ b/arch/powerpc/dts/km836x-uboot.dtsi @@ -0,0 +1,61 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * ABB PGGA km836x U-Boot specific Device Tree Source parts + * + * Copyright (C) 2020 Heiko Schocher hs@denx.de + * + */ + +/ { + cpus { + u-boot,dm-pre-reloc; + PowerPC,8360@0 { + u-boot,dm-pre-reloc; + }; + }; + + chosen { + stdout-path = &serial0; + }; +}; + +&qe { + compatible = "fsl,qe", "simple-bus"; +}; + +&soc { + u-boot,dm-pre-reloc; + + par_io@1400 { + u-boot,dm-pre-reloc; + + serial_pin@0 { + u-boot,dm-pre-reloc; + }; + ucc_pin@0 { + u-boot,dm-pre-reloc; + }; + ucc_pin@1 { + u-boot,dm-pre-reloc; + }; + ucc_pin@3 { + u-boot,dm-pre-reloc; + }; + ucc_pin@4 { + u-boot,dm-pre-reloc; + }; + ucc_pin@5 { + u-boot,dm-pre-reloc; + }; + ucc_pin@6 { + u-boot,dm-pre-reloc; + }; + ucc_pin@7 { + u-boot,dm-pre-reloc; + }; + }; +}; + +&serial0 { + u-boot,dm-pre-reloc; +}; diff --git a/arch/powerpc/dts/km836x.dtsi b/arch/powerpc/dts/km836x.dtsi new file mode 100644 index 0000000000..a8c83fc7e3 --- /dev/null +++ b/arch/powerpc/dts/km836x.dtsi @@ -0,0 +1,182 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * ABB PGGA km836x common ports Device Tree Source + * + * Copyright (C) 2020 Heiko Schocher hs@denx.de + * + */ + +/dts-v1/; + +/ { + #address-cells = <1>; + #size-cells = <1>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + PowerPC,8360@0 { + device_type = "cpu"; + reg = <0x0>; + d-cache-line-size = <32>; /* 32 bytes */ + i-cache-line-size = <32>; /* 32 bytes */ + d-cache-size = <32768>; /* L1, 32K */ + i-cache-size = <32768>; /* L1, 32K */ + timebase-frequency = <0>; /* Filled in by U-Boot */ + bus-frequency = <0>; /* Filled in by U-Boot */ + clock-frequency = <0>; /* Filled in by U-Boot */ + }; + }; + + memory { + device_type = "memory"; + reg = <0 0>; /* Filled in by U-Boot */ + }; + + soc: soc8360@e0000000 { + #address-cells = <1>; + #size-cells = <1>; + device_type = "soc"; + compatible = "fsl,mpc8360-immr", "simple-bus"; + ranges = <0x0 0xe0000000 0x00200000>; + reg = <0xe0000000 0x00000200>; + bus-frequency = <0>;/* Filled in by U-Boot */ + + /* power management control module*/ + pmc: power@b00 { + compatible = "fsl,mpc8360-pmc", "fsl,mpc8349-pmc"; + reg = <0xb00 0x100 0xa00 0x100>; + interrupts = <80 0x8>; + interrupt-parent = <&ipic>; + }; + + i2c0: i2c@3000 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + compatible = "fsl,mpc8313-i2c","fsl-i2c"; + reg = <0x3000 0x100>; + interrupts = <14 0x8>; + interrupt-parent = <&ipic>; + clock-frequency = <100000>; + }; + + serial0: serial@4500 { + cell-index = <0>; + device_type = "serial"; + compatible = "fsl,ns16550", "ns16550"; + reg = <0x4500 0x100>; + clock-frequency = <264000000>; + interrupts = <9 0x8>; + interrupt-parent = <&ipic>; + status = "disabled"; + }; + + serial1: serial@4600 { + cell-index = <1>; + device_type = "serial"; + compatible = "fsl,ns16550", "ns16550"; + reg = <0x4600 0x100>; + clock-frequency = <133333333>; + interrupts = <10 0x8>; + interrupt-parent = <&ipic>; + status = "disabled"; + }; + + ipic: pic@700 { + #address-cells = <0>; + #interrupt-cells = <2>; + compatible = "fsl,pq2pro-pic", "fsl,ipic"; + interrupt-controller; + reg = <0x700 0x100>; + }; + + par_io: par_io@1400 { + #address-cells = <1>; + #size-cells = <1>; + reg = <0x1400 0x100>; + ranges; + compatible = "fsl,mpc8360-par_io"; + device_type = "par_io"; + num-ports = <7>; + + qe_pio_c: gpio-controller@30 { + #gpio-cells = <2>; + compatible = "fsl,mpc8360-qe-pario-bank", + "fsl,mpc8323-qe-pario-bank"; + reg = <0x1430 0x18>; + gpio-controller; + }; + }; + + qe: qe@100000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,qe"; + ranges = <0x0 0x100000 0x100000>; + reg = <0x100000 0x480>; + clock-frequency = <0>; /* Filled in by U-Boot */ + brg-frequency = <0>; /* Filled in by U-Boot */ + bus-frequency = <0>; /* Filled in by U-Boot */ + + muram@10000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,qe-muram", "fsl,cpm-muram"; + ranges = <0x0 0x00010000 0x0000c000>; + + data-only@0 { + compatible = "fsl,qe-muram-data", + "fsl,cpm-muram-data"; + reg = <0x0 0xc000>; + }; + }; + + qeic: interrupt-controller@80 { + interrupt-controller; + compatible = "fsl,qe-ic"; + #address-cells = <0>; + #interrupt-cells = <1>; + reg = <0x80 0x80>; + big-endian; + interrupts = < + 32 0x8 /* ucc1 */ + 33 0x8 /* ucc2 */ + 34 0x8 /* ucc3 */ + 35 0x8 /* ucc4 */ + 40 0x8 /* ucc1 */ + >; + interrupt-parent = <&ipic>; + }; + + spi0: spi@4c0 { + cell-index = <0>; + compatible = "fsl,spi"; + reg = <0x4c0 0x40>; + interrupts = <2>; + interrupt-parent = <&qeic>; + mode = "qe"; + #address-cells = <1>; + #size-cells = <0>; + pio-handle = <&pio_spi>; + }; + + bootcount@0x1bff8 { + device_type = "bootcount"; + compatible = "u-boot,bootcount"; + reg = <0x1bff8 0x08>; + }; + }; + }; + + localbus: localbus@e0005000 { + #address-cells = <2>; + #size-cells = <1>; + compatible = "fsl,mpc8360-localbus", "fsl,pq2pro-localbus", + "simple-bus"; + reg = <0xe0005000 0xd8>; + }; +}; + +#include "km836x-uboot.dtsi" diff --git a/arch/powerpc/dts/kmcoge5ne-uboot.dtsi b/arch/powerpc/dts/kmcoge5ne-uboot.dtsi new file mode 100644 index 0000000000..6a5e74f434 --- /dev/null +++ b/arch/powerpc/dts/kmcoge5ne-uboot.dtsi @@ -0,0 +1,22 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * ABB PGGA kmcoge5ne U-Boot specific Device Tree Source parts + * + * Copyright (C) 2020 Heiko Schocher hs@denx.de + * + */ + +/ { + aliases { + /delete-property/ ethernet1; + /delete-property/ ethernet2; + }; +}; + +&enet_switch { + status = "disabled"; +}; + +&enet_mate { + status = "disabled"; +}; diff --git a/arch/powerpc/dts/kmcoge5ne.dts b/arch/powerpc/dts/kmcoge5ne.dts new file mode 100644 index 0000000000..467e5bd9d2 --- /dev/null +++ b/arch/powerpc/dts/kmcoge5ne.dts @@ -0,0 +1,320 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * ABB PGGA KMCOGE5ne Device Tree Source + * + * Copyright (C) 2020 Heiko Schocher hs@denx.de + * + */ + +/dts-v1/; + +#include "km836x.dtsi" + +/ { + model = "kmcoge5ne"; + compatible = "ABB,kmcoge5ne"; + + aliases { + ethernet0 = &enet_admin; + ethernet1 = &enet_mate; + ethernet2 = &enet_switch; + serial0 = &serial0; + }; +}; + +&soc { + /* brg for hdlc clk */ + brg@0 { + compatible = "fsl,mpc-brg"; + brg-name = "brg16"; + brg-frequency = <20000000>; /* 20 MHz */ + pio-handle = <&pio_brg>; + }; +}; + +&i2c0 { + mux@70 { + compatible = "nxp,pca9547"; + reg = <0x70>; + #address-cells = <1>; + #size-cells = <0>; + + i2c@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + /* Inventory EEPROM of the unit itself */ + ivm@50 { + label = "MAIN_CTRL"; + compatible = "dummy"; + reg = <0x50>; + }; + }; + + i2c@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + /* Inventory EEPROM of the fan unit */ + fanu-ivm@50 { + label = "FANUV"; + compatible = "dummy"; + reg = <0x50>; + }; + + /* fan unit (GPIOs and so on) */ + fanu@20 { + label = "FANUV_CTRL"; + compatible = "dummy"; + reg = <0x20>; + }; + }; + + i2c@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + + backplane@50 { + label = "BP_CTRL"; + compatible = "dummy"; + reg = <0x50>; + }; + }; + }; +}; + +&serial0 { + status = "okay"; +}; + +&par_io { + pio_ucc1: ucc_pin@0 { /* RGMII mng-switch */ + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 0 1 3 0 2 0 /* MDIO (PA1, bi, f2) */ + 0 2 1 0 1 0 /* MDC (PA2, in, f1) */ + + 0 3 1 0 1 0 /* TxD0 (PA3, in, f1) */ + 0 4 1 0 1 0 /* TxD1 (PA4, in, f1) */ + 0 5 1 0 1 0 /* TxD2 (PA5, in, f1) */ + 0 6 1 0 1 0 /* TxD3 (PA6, in, f1) */ + 0 9 2 0 1 0 /* RxD0 (PA9, out, f1) */ + 0 10 2 0 1 0 /* RxD1 (PA10, out, f1) */ + 0 11 2 0 1 0 /* RxD2 (PA11, out, f1) */ + 0 12 2 0 1 0 /* RxD3 (PA12, out, f1) */ + 0 7 1 0 1 0 /* TX_EN (PA7, in, f1) */ + 0 15 2 0 1 0 /* RX_DV (PA15, out, f1) */ + 0 0 2 0 1 0 /* RX_CLK (PA0, out, f1) */ + 2 9 1 0 3 0 /* GTX_CLK (CLK10) */ + 2 8 2 0 1 0 /* GTX125 (CLK9) */ + >; + }; + + pio_ucc4: ucc_pin@3 { /* RMII, admin front port */ + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 0 1 3 0 2 0 /* MDIO (PA1, bi, f2) */ + 0 2 1 0 1 0 /* MDC (PA2, in, f1) */ + + 1 14 1 0 1 0 /* TxD0 (PB14, out, f1) */ + 1 15 1 0 1 0 /* TxD1 (PB15, out, f1) */ + 1 20 2 0 1 0 /* RxD0 (PB20, in, f1) */ + 1 21 2 0 1 0 /* RxD1 (PB21, in, f1) */ + 1 18 1 0 1 0 /* TX_EN (PB18, out, f1) */ + 1 26 2 0 1 0 /* RX_DV (PB26, in, f1) */ + 1 27 2 0 1 0 /* RX_ER (PB27, in, f1) */ + + 2 16 2 0 1 0 /* UCC4_RMII_CLK (CLK17) */ + >; + }; + + pio_ucc5: ucc_pin@4 { /* RMII, mate backplane port */ + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 0 1 3 0 2 0 /* MDIO (PA1, bi, f2) */ + 0 2 1 0 1 0 /* MDC (PA2, in, f1) */ + + 3 0 1 0 1 0 /* TxD0 (PD0, out, f1) */ + 3 1 1 0 1 0 /* TxD1 (PD1, out, f1) */ + 3 6 2 0 1 0 /* RxD0 (PD6, in, f1) */ + 3 7 2 0 1 0 /* RxD1 (PD7, in, f1) */ + 3 4 1 0 1 0 /* TX_EN (PD4, out, f1) */ + 3 12 2 0 1 0 /* RX_DV (PD12, in, f1) */ + 3 13 2 0 1 0 /* RX_ER (PD13, in, f1) */ + + 2 15 2 0 1 0 /* UCCx_RMII_CLK (CLK16) */ + >; + }; + + pio_spi: spi_pin@01 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 4 28 3 0 3 0 /* SPI_MOSI (PE28, out, f3) */ + 4 29 3 0 3 0 /* SPI_MISO (PE29, out, f3) */ + 4 30 3 0 3 0 /* SPI_CLK (PE30, out, f3) */ + >; + }; + + pio_brg: brg_pin@0 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 2 25 1 0 1 0 /* BRG (PC25, out, f1) */ + >; + }; + + pio_tdm: tdm_pin@00 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + /* TDMa */ + 0 8 3 0 2 0 /* RxD0 (PA8, bi, f2) */ + 0 13 3 0 2 0 /* TxD0 (PA13, bi, f2) */ + 0 14 2 0 2 0 /* RSync0 (PA14, in, f2) */ + 2 7 2 0 1 0 /* RxClk8 (PC7, in, f1) */ + /* TDMb */ + 0 27 3 0 2 0 /* RxD1 (PA27, bi, f2) */ + 0 22 3 0 2 0 /* TxD1 (PA22, bi, f2) */ + 0 28 2 0 2 0 /* RSync1 (PA28, in, f2) */ + 2 1 2 0 1 0 /* RxClk2 (PC1, in, f1) */ + /* TDMc */ + 1 5 3 0 2 0 /* RxD2 (PB5, bi, f2) */ + 1 8 3 0 2 0 /* TxD2 (PB8, bi, f2) */ + 1 2 2 0 3 0 /* RSync2 (PB2, in, f3) */ + 2 6 2 0 1 0 /* RxClk7 (PC6, in, f1) */ + /* TDMd */ + 1 22 3 0 2 0 /* RxD3 (PB22, bi, f2) */ + 1 19 3 0 1 0 /* TxD3 (PB19, bi, f1) */ + 1 16 2 0 2 0 /* RSync3 (PB16, in, f2) */ + 2 13 2 0 1 0 /* RxClk14 (PC13, in, f1) */ + /* TDMe */ + 3 8 3 0 2 0 /* RxD4 (PD8, bi, f2) */ + 3 5 3 0 2 0 /* TxD4 (PD5, bi, f2) */ + 3 2 2 0 2 0 /* RSync4 (PD2 , in, f2) */ + 2 22 2 0 1 0 /* RxClk23 (PC22, in, f1) */ + /* TDMf */ + 3 19 3 0 2 0 /* RxD5 (PD19, bi, f2) */ + 3 22 3 0 2 0 /* TxD5 (PD22, bi, f2) */ + 3 16 2 0 1 0 /* RSync5 (PD16, in, f1) */ + 2 17 2 0 1 0 /* RxClk18 (PC17, in, f1) */ + /* TDMg */ + 4 8 3 0 2 0 /* RxD6 (PE8, bi, f2) */ + 4 5 3 0 2 0 /* TxD6 (PE5, bi, f2) */ + 4 2 2 0 1 0 /* RSync6 (PE2, in, f1) */ + 2 19 2 0 1 0 /* RxClk20 (PC19, in, f1) */ + /* TDMh */ + 4 19 3 0 2 0 /* RxD7 (PE19, bi, f2) */ + 4 22 3 0 3 0 /* TxD7 (PE22, bi, f3) */ + 4 16 2 0 2 0 /* RSync7 (PE16, in, f2) */ + 2 21 2 0 1 0 /* RxClk22 (PC21, in, f1) */ + /* RxTxClk0/1 */ + 2 0 2 0 1 0 /* Clk1 (PC0, in, f1) */ + 2 23 2 0 1 0 /* Clk24 (PC23, in, f1) */ + /* RxTxSync0/1 */ + 2 10 2 0 1 0 /* Clk11 (PC10, in, f1) */ + 2 20 2 0 1 0>; /* Clk21 (PC20, in, f1) */ + }; +}; + +&qe { + /* mng-switch port (UCC1, MDIO 0x10, RGMII) */ + enet_switch: ethernet@2000 { + device_type = "network"; + compatible = "ucc_geth"; + cell-index = <1>; + reg = <0x2000 0x200>; + interrupts = <32>; + interrupt-parent = <&qeic>; + local-mac-address = [ 00 00 00 00 00 00 ]; + rx-clock-name = "none"; + tx-clock-name = "clk9"; + /*id=0, full-dup, 1G, no-pause, no-asym_p*/ + fixed-link = <0 1 1000 0 0>; + phy-connection-type = "rgmii-id"; + pio-handle = <&pio_ucc1>; + }; + + /* admin and debug port (UCC4, MDIO 0x00, RMII) */ + enet_admin: ucc@3200 { + device_type = "network"; + compatible = "ucc_geth"; + cell-index = <4>; + reg = <0x3200 0x200>; + interrupts = <35>; + interrupt-parent = <&qeic>; + local-mac-address = [ 00 00 00 00 00 00 ]; + rx-clock-name = "none"; + tx-clock-name = "clk17"; + phy-handle = <&phy_admin>; + phy-connection-type = "rmii"; + pio-handle = <&pio_ucc4>; + }; + + /* mate backplane port (UCC5, MDIO 0x08, RMII) */ + enet_mate: ucc@2400 { + device_type = "network"; + compatible = "ucc_geth"; + cell-index = <5>; + reg = <0x2400 0x200>; + interrupts = <40>; + interrupt-parent = <&qeic>; + local-mac-address = [ 00 00 00 00 00 00 ]; + rx-clock-name = "none"; + tx-clock-name = "clk16"; + phy-handle = <&phy_mate>; + phy-connection-type = "rmii"; + pio-handle = <&pio_ucc5>; + }; + + mdio@3320 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x3320 0x18>; + compatible = "fsl,ucc-mdio"; + + /* admin front port (UCC4, MDIO 0x00, RMII) */ + phy_admin: ethernet-phy@00 { + reg = <0x0>; + }; + + /* mate bp port (UCC5, MDIO 0x08, RMII) */ + phy_mate: ethernet-phy@08 { + reg = <0x08>; + }; + }; +}; + +&localbus { + ranges = <0 0 0xf0000000 0x04000000 + 1 0 0xe8000000 0x01000000 + 3 0 0xa0000000 0x10000000 + 4 0 0xb0000000 0x10000000>; + + flash@0,0 { + compatible = "cfi-flash"; + reg = <0 0 0x04000000>; + nornand = "nor"; + #address-cells = <1>; + #size-cells = <1>; + bank-width = <2>; + partition@0 { /* 768KB */ + label = "u-boot"; + reg = <0 0xC0000>; + }; + partition@c0000 { /* 128KB */ + label = "env"; + reg = <0xC0000 0x20000>; + }; + partition@e0000 { /* 128KB */ + label = "envred"; + reg = <0xE0000 0x20000>; + }; + partition@100000 { /* 64512KB */ + label = "ubi0"; + reg = <0x100000 0x3F00000>; + }; + }; +}; + +#include "kmcoge5ne-uboot.dtsi" diff --git a/arch/powerpc/dts/kmeter1-uboot.dtsi b/arch/powerpc/dts/kmeter1-uboot.dtsi new file mode 100644 index 0000000000..898fa7dc7a --- /dev/null +++ b/arch/powerpc/dts/kmeter1-uboot.dtsi @@ -0,0 +1,42 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * ABB PGGA kmeter1 U-Boot specific Device Tree Source parts + * + * Copyright (C) 2020 Heiko Schocher hs@denx.de + * + */ + +/ { + aliases { + /delete-property/ ethernet1; + /delete-property/ ethernet2; + /delete-property/ ethernet3; + /delete-property/ ethernet4; + /delete-property/ ethernet5; + /delete-property/ ethernet6; + }; +}; + +&enet_estar1 { + status = "disabled"; +}; + +&enet_estar2 { + status = "disabled"; +}; + +&enet_eth1 { + status = "disabled"; +}; + +&enet_eth2 { + status = "disabled"; +}; + +&enet_eth3 { + status = "disabled"; +}; + +&enet_eth4 { + status = "disabled"; +}; diff --git a/arch/powerpc/dts/kmeter1.dts b/arch/powerpc/dts/kmeter1.dts new file mode 100644 index 0000000000..f1f79952ab --- /dev/null +++ b/arch/powerpc/dts/kmeter1.dts @@ -0,0 +1,480 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * ABB PGGA KMETER1 Device Tree Source + * + * 2008-2011 DENX Software Engineering GmbH + * Copyright (C) 2020 Heiko Schocher hs@denx.de + */ + +/dts-v1/; + +#include "km836x.dtsi" + +/ { + model = "KMETER1"; + compatible = "ABB,KMETER1"; + + aliases { + ethernet0 = &enet_piggy2; + ethernet1 = &enet_estar1; + ethernet2 = &enet_estar2; + ethernet3 = &enet_eth1; + ethernet4 = &enet_eth2; + ethernet5 = &enet_eth3; + ethernet6 = &enet_eth4; + serial0 = &serial0; + }; +}; + +&i2c0 { + mux@70 { + compatible = "nxp,pca9547"; + reg = <0x70>; + #address-cells = <1>; + #size-cells = <0>; + + i2c@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + /* Inventory EEPROM of the unit itself */ + ivm@50 { + label = "MAIN_CTRL"; + compatible = "dummy"; + reg = <0x50>; + }; + }; + + i2c@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + /* Temperature sensors */ + temp@48 { + label = "Top"; + compatible = "national,lm75"; + reg = <0x48>; + }; + + temp@49 { + label = "Control"; + compatible = "national,lm75"; + reg = <0x49>; + }; + + temp@4a { + label = "Power"; + compatible = "national,lm75"; + reg = <0x4a>; + }; + + temp@4b { + label = "Front"; + compatible = "national,lm75"; + reg = <0x4b>; + }; + }; + }; +}; + +&serial0 { + status = "okay"; +}; + +&par_io { + pio_ucc1: ucc_pin@0 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 0 1 3 0 2 0 /* MDIO */ + 0 2 1 0 1 0 /* MDC */ + + 0 3 1 0 1 0 /* TxD0 */ + 0 4 1 0 1 0 /* TxD1 */ + 0 5 1 0 1 0 /* TxD2 */ + 0 6 1 0 1 0 /* TxD3 */ + 0 9 2 0 1 0 /* RxD0 */ + 0 10 2 0 1 0 /* RxD1 */ + 0 11 2 0 1 0 /* RxD2 */ + 0 12 2 0 1 0 /* RxD3 */ + 0 7 1 0 1 0 /* TX_EN */ + 0 8 1 0 1 0 /* TX_ER */ + 0 15 2 0 1 0 /* RX_DV */ + 0 16 2 0 1 0 /* RX_ER */ + 0 0 2 0 1 0 /* RX_CLK */ + 2 9 1 0 3 0 /* GTX_CLK - CLK10 */ + 2 8 2 0 1 0 /* GTX125 - CLK9 */ + >; + }; + + pio_ucc2: ucc_pin@1 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 0 1 3 0 2 0 /* MDIO */ + 0 2 1 0 1 0 /* MDC */ + + 0 17 1 0 1 0 /* TxD0 */ + 0 18 1 0 1 0 /* TxD1 */ + 0 19 1 0 1 0 /* TxD2 */ + 0 20 1 0 1 0 /* TxD3 */ + 0 23 2 0 1 0 /* RxD0 */ + 0 24 2 0 1 0 /* RxD1 */ + 0 25 2 0 1 0 /* RxD2 */ + 0 26 2 0 1 0 /* RxD3 */ + 0 21 1 0 1 0 /* TX_EN */ + 0 22 1 0 1 0 /* TX_ER */ + 0 29 2 0 1 0 /* RX_DV */ + 0 30 2 0 1 0 /* RX_ER */ + 0 31 2 0 1 0 /* RX_CLK */ + 2 2 1 0 2 0 /* GTX_CLK - CLK3 */ + 2 3 2 0 1 0 /* GTX125 - CLK4 */ + >; + }; + + pio_ucc4: ucc_pin@3 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 0 1 3 0 2 0 /* MDIO */ + 0 2 1 0 1 0 /* MDC */ + + 1 14 1 0 1 0 /* TxD0 (PB14, out, f1) */ + 1 15 1 0 1 0 /* TxD1 (PB15, out, f1) */ + 1 20 2 0 1 0 /* RxD0 (PB20, in, f1) */ + 1 21 2 0 1 0 /* RxD1 (PB21, in, f1) */ + 1 18 1 0 1 0 /* TX_EN (PB18, out, f1) */ + 1 26 2 0 1 0 /* RX_DV (PB26, in, f1) */ + 1 27 2 0 1 0 /* RX_ER (PB27, in, f1) */ + + 2 16 2 0 1 0 /* UCC4_RMII_CLK (CLK17) */ + >; + }; + + pio_ucc5: ucc_pin@4 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 0 1 3 0 2 0 /* MDIO */ + 0 2 1 0 1 0 /* MDC */ + + 3 0 1 0 1 0 /* TxD0 (PD0, out, f1) */ + 3 1 1 0 1 0 /* TxD1 (PD1, out, f1) */ + 3 6 2 0 1 0 /* RxD0 (PD6, in, f1) */ + 3 7 2 0 1 0 /* RxD1 (PD7, in, f1) */ + 3 4 1 0 1 0 /* TX_EN (PD4, out, f1) */ + 3 12 2 0 1 0 /* RX_DV (PD12, in, f1) */ + 3 13 2 0 1 0 /* RX_ER (PD13, in, f1) */ + >; + }; + + pio_ucc6: ucc_pin@5 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 0 1 3 0 2 0 /* MDIO */ + 0 2 1 0 1 0 /* MDC */ + + 3 14 1 0 1 0 /* TxD0 (PD14, out, f1) */ + 3 15 1 0 1 0 /* TxD1 (PD15, out, f1) */ + 3 20 2 0 1 0 /* RxD0 (PD20, in, f1) */ + 3 21 2 0 1 0 /* RxD1 (PD21, in, f1) */ + 3 18 1 0 1 0 /* TX_EN (PD18, out, f1) */ + 3 26 2 0 1 0 /* RX_DV (PD26, in, f1) */ + 3 27 2 0 1 0 /* RX_ER (PD27, in, f1) */ + >; + }; + + pio_ucc7: ucc_pin@6 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 0 1 3 0 2 0 /* MDIO */ + 0 2 1 0 1 0 /* MDC */ + + 4 0 1 0 1 0 /* TxD0 (PE0, out, f1) */ + 4 1 1 0 1 0 /* TxD1 (PE1, out, f1) */ + 4 6 2 0 1 0 /* RxD0 (PE6, in, f1) */ + 4 7 2 0 1 0 /* RxD1 (PE7, in, f1) */ + 4 4 1 0 1 0 /* TX_EN (PE4, out, f1) */ + 4 12 2 0 1 0 /* RX_DV (PE12, in, f1) */ + 4 13 2 0 1 0 /* RX_ER (PE13, in, f1) */ + >; + }; + + pio_ucc8: ucc_pin@7 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 0 1 3 0 2 0 /* MDIO */ + 0 2 1 0 1 0 /* MDC */ + + 4 14 1 0 2 0 /* TxD0 (PE14, out, f2) */ + 4 15 1 0 1 0 /* TxD1 (PE15, out, f1) */ + 4 20 2 0 1 0 /* RxD0 (PE20, in, f1) */ + 4 21 2 0 1 0 /* RxD1 (PE21, in, f1) */ + 4 18 1 0 1 0 /* TX_EN (PE18, out, f1) */ + 4 26 2 0 1 0 /* RX_DV (PE26, in, f1) */ + 4 27 2 0 1 0 /* RX_ER (PE27, in, f1) */ + + 2 15 2 0 1 0 /* UCCx_RMII_CLK (CLK16) */ + >; + }; + + pio_spi: spi_pin@01 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 4 28 3 0 3 0 /* SPI_MOSI (PE28, out, f3 */ + 4 30 3 0 3 0 /* SPI_CLK (PE30, out, f3 */ + >; + }; + + /* UCC3 as HDLC controller for ICN */ + pio5: ucc_pin@02 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 1 0 1 0 1 0 /* TxD0 */ + 1 6 2 0 1 0 /* RxD0 */ + 1 12 2 0 1 0 /* CTS */ + 2 11 2 0 1 0 /* TX-CLK12 */ + >; + }; + + pio_tdm: tdm_pin@00 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + /* TDMa */ + 0 8 3 0 2 0 /* RxD0 (PA8, bi, f2) */ + 0 13 3 0 2 0 /* TxD0 (PA13, bi, f2) */ + 0 14 2 0 2 0 /* RSync0 (PA14, in, f2) */ + 2 7 2 0 1 0 /* RxClk8 (PC7, in, f1) */ + /* TDMb */ + 0 27 3 0 2 0 /* RxD1 (PA27, bi, f2) */ + 0 22 3 0 2 0 /* TxD1 (PA22, bi, f2) */ + 0 28 2 0 2 0 /* RSync1 (PA28, in, f2) */ + 2 1 2 0 1 0 /* RxClk2 (PC1, in, f1) */ + /* TDMc */ + 1 5 3 0 2 0 /* RxD2 (PB5, bi, f2) */ + 1 8 3 0 2 0 /* TxD2 (PB8, bi, f2) */ + 1 2 2 0 3 0 /* RSync2 (PB2, in, f3) */ + 2 6 2 0 1 0 /* RxClk7 (PC6, in, f1) */ + /* TDMd */ + 1 22 3 0 2 0 /* RxD3 (PB22, bi, f2) */ + 1 19 3 0 1 0 /* TxD3 (PB19, bi, f1) */ + 1 16 2 0 2 0 /* RSync3 (PB16, in, f2) */ + 2 13 2 0 1 0 /* RxClk14 (PC13, in, f1) */ + /* TDMe */ + 3 8 3 0 2 0 /* RxD4 (PD8, bi, f2) */ + 3 5 3 0 2 0 /* TxD4 (PD5, bi, f2) */ + 3 2 2 0 2 0 /* RSync4 (PD2 , in, f2) */ + 2 22 2 0 1 0 /* RxClk23 (PC22, in, f1) */ + /* TDMf */ + 3 19 3 0 2 0 /* RxD5 (PD19, bi, f2) */ + 3 22 3 0 2 0 /* TxD5 (PD22, bi, f2) */ + 3 16 2 0 1 0 /* RSync5 (PD16, in, f1) */ + 2 17 2 0 1 0 /* RxClk18 (PC17, in, f1) */ + /* TDMg */ + 4 8 3 0 2 0 /* RxD6 (PE8, bi, f2) */ + 4 5 3 0 2 0 /* TxD6 (PE5, bi, f2) */ + 4 2 2 0 1 0 /* RSync6 (PE2, in, f1) */ + 2 19 2 0 1 0 /* RxClk20 (PC19, in, f1) */ + /* TDMh */ + 4 19 3 0 2 0 /* RxD7 (PE19, bi, f2) */ + 4 22 3 0 3 0 /* TxD7 (PE22, bi, f3) */ + 4 16 2 0 2 0 /* RSync7 (PE16, in, f2) */ + 2 21 2 0 1 0 /* RxClk22 (PC21, in, f1) */ + /* RxTxClk0/1 */ + 2 0 2 0 1 0 /* Clk1 (PC0, in, f1) */ + 2 23 2 0 1 0 /* Clk24 (PC23, in, f1) */ + /* RxTxSync0/1 */ + 2 10 2 0 1 0 /* Clk11 (PC10, in, f1) */ + 2 20 2 0 1 0>; /* Clk21 (PC20, in, f1) */ + }; +}; + +&qe { + /* ESTAR-1 (UCC1, MDIO 0x10, RGMII) */ + enet_estar1: ucc@2000 { + device_type = "network"; + compatible = "ucc_geth"; + cell-index = <1>; + reg = <0x2000 0x200>; + interrupts = <32>; + interrupt-parent = <&qeic>; + local-mac-address = [ 00 00 00 00 00 00 ]; + rx-clock-name = "none"; + tx-clock-name = "clk9"; + phy-handle = <&phy_estar1>; + phy-connection-type = "rgmii-id"; + pio-handle = <&pio_ucc1>; + }; + + /* ESTAR-2 (UCC2, MDIO 0x11, RGMII) */ + enet_estar2: ucc@3000 { + device_type = "network"; + compatible = "ucc_geth"; + cell-index = <2>; + reg = <0x3000 0x200>; + interrupts = <33>; + interrupt-parent = <&qeic>; + local-mac-address = [ 00 00 00 00 00 00 ]; + rx-clock-name = "none"; + tx-clock-name = "clk4"; + phy-handle = <&phy_estar2>; + phy-connection-type = "rgmii-id"; + pio-handle = <&pio_ucc2>; + }; + + /* Piggy2 (UCC4, MDIO 0x00, RMII) */ + enet_piggy2: ucc@3200 { + device_type = "network"; + compatible = "ucc_geth"; + cell-index = <4>; + reg = <0x3200 0x200>; + interrupts = <35>; + interrupt-parent = <&qeic>; + local-mac-address = [ 00 00 00 00 00 00 ]; + rx-clock-name = "none"; + tx-clock-name = "clk17"; + phy-handle = <&phy_piggy2>; + phy-connection-type = "rmii"; + pio-handle = <&pio_ucc4>; + }; + + /* Eth-1 (UCC5, MDIO 0x08, RMII) */ + enet_eth1: ucc@2400 { + device_type = "network"; + compatible = "ucc_geth"; + cell-index = <5>; + reg = <0x2400 0x200>; + interrupts = <40>; + interrupt-parent = <&qeic>; + local-mac-address = [ 00 00 00 00 00 00 ]; + rx-clock-name = "none"; + tx-clock-name = "clk16"; + phy-handle = <&phy_eth1>; + phy-connection-type = "rmii"; + pio-handle = <&pio_ucc5>; + }; + + /* Eth-2 (UCC6, MDIO 0x09, RMII) */ + enet_eth2: ucc@3400 { + device_type = "network"; + compatible = "ucc_geth"; + cell-index = <6>; + reg = <0x3400 0x200>; + interrupts = <41>; + interrupt-parent = <&qeic>; + local-mac-address = [ 00 00 00 00 00 00 ]; + rx-clock-name = "none"; + tx-clock-name = "clk16"; + phy-handle = <&phy_eth2>; + phy-connection-type = "rmii"; + pio-handle = <&pio_ucc6>; + }; + + /* Eth-3 (UCC7, MDIO 0x0a, RMII) */ + enet_eth3: ucc@2600 { + device_type = "network"; + compatible = "ucc_geth"; + cell-index = <7>; + reg = <0x2600 0x200>; + interrupts = <42>; + interrupt-parent = <&qeic>; + local-mac-address = [ 00 00 00 00 00 00 ]; + rx-clock-name = "none"; + tx-clock-name = "clk16"; + phy-handle = <&phy_eth3>; + phy-connection-type = "rmii"; + pio-handle = <&pio_ucc7>; + }; + + /* Eth-4 (UCC8, MDIO 0x0b, RMII) */ + enet_eth4: ucc@3600 { + device_type = "network"; + compatible = "ucc_geth"; + cell-index = <8>; + reg = <0x3600 0x200>; + interrupts = <43>; + interrupt-parent = <&qeic>; + local-mac-address = [ 00 00 00 00 00 00 ]; + rx-clock-name = "none"; + tx-clock-name = "clk16"; + phy-handle = <&phy_eth4>; + phy-connection-type = "rmii"; + pio-handle = <&pio_ucc8>; + }; + + mdio@3320 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x3320 0x18>; + compatible = "fsl,ucc-mdio"; + + /* Piggy2 (UCC4, MDIO 0x00, RMII) */ + phy_piggy2: ethernet-phy@0 { + reg = <0x0>; + }; + + /* Eth-1 (UCC5, MDIO 0x08, RMII) */ + phy_eth1: ethernet-phy@8 { + reg = <0x08>; + }; + + /* Eth-2 (UCC6, MDIO 0x09, RMII) */ + phy_eth2: ethernet-phy@9 { + reg = <0x09>; + }; + + /* Eth-3 (UCC7, MDIO 0x0a, RMII) */ + phy_eth3: ethernet-phy@a { + reg = <0x0a>; + }; + + /* Eth-4 (UCC8, MDIO 0x0b, RMII) */ + phy_eth4: ethernet-phy@b { + reg = <0x0b>; + }; + + /* ESTAR-1 (UCC1, MDIO 0x10, RGMII) */ + phy_estar1: ethernet-phy@10 { + interrupt-parent = <&ipic>; + interrupts = <17 0x8>; + reg = <0x10>; + }; + + /* ESTAR-2 (UCC2, MDIO 0x11, RGMII) */ + phy_estar2: ethernet-phy@11 { + interrupt-parent = <&ipic>; + interrupts = <18 0x8>; + reg = <0x11>; + }; + }; +}; + +&localbus { + ranges = <0 0 0xf0000000 0x04000000 /* LB 0 */ + 1 0 0xe8000000 0x01000000 /* LB 1 */ + 3 0 0xa0000000 0x10000000>; /* LB 3 */ + + flash@0,0 { + compatible = "cfi-flash"; + reg = <0 0 0x04000000>; + #address-cells = <1>; + #size-cells = <1>; + bank-width = <2>; + partition@0 { /* 768KB */ + label = "u-boot"; + reg = <0 0xC0000>; + }; + partition@c0000 { /* 128KB */ + label = "env"; + reg = <0xC0000 0x20000>; + }; + partition@e0000 { /* 128KB */ + label = "envred"; + reg = <0xE0000 0x20000>; + }; + partition@100000 { /* 64512KB */ + label = "ubi0"; + reg = <0x100000 0x3F00000>; + }; + }; +}; + +#include "kmeter1-uboot.dtsi" diff --git a/arch/powerpc/dts/kmopti2.dts b/arch/powerpc/dts/kmopti2.dts new file mode 100644 index 0000000000..23e31872dd --- /dev/null +++ b/arch/powerpc/dts/kmopti2.dts @@ -0,0 +1,161 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * ABB PGGA OPTI2 Device Tree Source + * + * Copyright (C) 2020 Heiko Schocher hs@denx.de + * + */ + +/dts-v1/; + +#include "km8321.dtsi" + +/ { + model = "KMOPTI2"; + compatible = "ABB,kmpbec8321"; + #address-cells = <1>; + #size-cells = <1>; + + aliases { + ethernet0 = &enet_piggy2; + serial0 = &serial0; + }; +}; + +&i2c0 { + mux@70 { + compatible = "nxp,pca9547"; + reg = <0x70>; + #address-cells = <1>; + #size-cells = <0>; + + i2c@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + /* Inventory EEPROM of the unit itself */ + ivm@50 { + label = "MAIN_CTRL"; + compatible = "dummy"; + reg = <0x50>; + }; + }; + + i2c@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + /* Temperature sensors */ + temp@49 { + label = "board"; + compatible = "national,lm75"; + reg = <0x49>; + }; + + temp@4a { + label = "power"; + compatible = "national,lm75"; + reg = <0x4a>; + }; + }; + + i2c@6 { + reg = <6>; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c@5 { + reg = <5>; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c@4 { + reg = <4>; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; +}; + +&par_io { + /* UCC5 as HDLC controller for ICN */ + pio_ucc5: ucc_pin@04 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 2 0 1 0 2 0 /* TxD0 */ + 2 8 2 0 2 0 /* RxD0 */ + 2 29 2 0 2 0 /* CTS */ + 3 30 2 0 1 0 /* ICN CLK */ + >; + }; + + /* UCC4 Piggy Ethernet */ + pio_ucc4: ucc_pin@03 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 3 4 3 0 2 0 /* MDIO */ + 3 5 1 0 2 0 /* MDC */ + + 1 18 1 0 1 0 /* TxD0 */ + 1 19 1 0 1 0 /* TxD1 */ + 1 22 2 0 1 0 /* RxD0 */ + 1 23 2 0 1 0 /* RxD1 */ + 1 26 2 0 1 0 /* RX_ER */ + 1 28 2 0 1 0 /* RX_DV */ + 1 30 1 0 1 0 /* TX_EN */ + 1 31 2 0 1 0 /* CRS */ + 3 10 2 0 3 0 /* UCC4_RMII_CLK (CLK17) */ + >; + }; + + pio_spi: spi_pin@01 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 3 0 3 0 1 0 /* SPI_MOSI (PD0, bi, f3) */ + 3 1 3 0 1 0 /* SPI_MISO (PD1, bi, f3) */ + 3 2 3 0 1 0 /* SPI_CLK (PD2, bi, f3) */ + >; + }; +}; + +&localbus { + ranges = <0 0 0xf0000000 0x04000000 /* LB 0 Flash (boot) */ + 1 0 0xe8000000 0x01000000 /* LB 1 PRIO1 and Piggy */ + 2 0 0xa0000000 0x10000000 /* LB 2 PAXE */ + 3 0 0xb0000000 0x10000000>; /* LB 3 OPI2 */ + + flash@0,0 { + compatible = "cfi-flash"; + reg = <0 0x00000000 0x04000000>; + bank-width = <2>; + #address-cells = <1>; + #size-cells = <1>; + use-advanced-sector-protection; + partition@0 { /* 768KB */ + label = "u-boot"; + reg = <0 0xC0000>; + }; + partition@c0000 { /* 128KB */ + label = "env"; + reg = <0xc0000 0x20000>; + }; + partition@e0000 { /* 128KB */ + label = "envred"; + reg = <0xe0000 0x20000>; + }; + partition@100000 { /* 64512KB */ + label = "ubi0"; + reg = <0x100000 0x3F00000>; + }; + }; +}; diff --git a/arch/powerpc/dts/kmsupc5.dts b/arch/powerpc/dts/kmsupc5.dts new file mode 100644 index 0000000000..60ca0d3324 --- /dev/null +++ b/arch/powerpc/dts/kmsupc5.dts @@ -0,0 +1,139 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * ABB PGGA SUPC5 Device Tree Source + * + * Copyright (C) 2020 Heiko Schocher hs@denx.de + * + */ + +/dts-v1/; + +#include "km8321.dtsi" + +/ { + model = "SUPC5"; + compatible = "ABB,kmpbec8321"; + #address-cells = <1>; + #size-cells = <1>; + + aliases { + ethernet0 = &enet_piggy2; + serial0 = &serial0; + }; +}; + +&i2c0 { + mux@70 { + compatible = "nxp,pca9547"; + reg = <0x70>; + #address-cells = <1>; + #size-cells = <0>; + + i2c@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + /* Inventory EEPROM of the unit itself */ + ivm@50 { + label = "MAIN_CTRL"; + compatible = "dummy"; + reg = <0x50>; + }; + }; + + i2c@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + /* Temperature sensors */ + temp@49 { + label = "board"; + compatible = "national,lm75"; + reg = <0x49>; + }; + }; + }; +}; + +&par_io { + /* UCC5 as HDLC controller for ICN */ + pio_ucc5: ucc_pin@04 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 2 0 1 0 2 0 /* TxD0 */ + 2 8 2 0 2 0 /* RxD0 */ + 2 29 2 0 2 0 /* CTS */ + 3 30 2 0 1 0 /* ICN CLK */ + >; + }; + + /* UCC4 Piggy Ethernet */ + pio_ucc4: ucc_pin@03 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 3 4 3 0 2 0 /* MDIO */ + 3 5 1 0 2 0 /* MDC */ + + 1 18 1 0 1 0 /* TxD0 */ + 1 19 1 0 1 0 /* TxD1 */ + 1 22 2 0 1 0 /* RxD0 */ + 1 23 2 0 1 0 /* RxD1 */ + 1 26 2 0 1 0 /* RX_ER */ + 1 28 2 0 1 0 /* RX_DV */ + 1 30 1 0 1 0 /* TX_EN */ + 1 31 2 0 1 0 /* CRS */ + /* UCC4_RMII_CLK (CLK17) */ + 3 10 2 0 3 0 + >; + }; + + pio_spi: spi_pin@01 { + pio-map = < + /* + * port pin dir open_drain assignment has_irq + * SPI_MOSI (PD0, bi, f3) + */ + 3 0 3 0 1 0 + /* SPI_MISO (PD1, bi, f3) */ + 3 1 3 0 1 0 + /* SPI_CLK (PD2, bi, f3) */ + 3 2 3 0 1 0 + >; + }; +}; + +&spi0 { + pio-handle = <&pio_spi>; +}; + +&localbus { + ranges = <0 0 0xf0000000 0x04000000 /* LB 0 Flash (boot) */ + 1 0 0xe8000000 0x01000000 /* LB 1 PRIO1 and Piggy */ + 2 0 0xa0000000 0x10000000>; /* LB 2 LPXF */ + + flash@0,0 { + compatible = "cfi-flash"; + reg = <0 0x00000000 0x04000000>; + bank-width = <2>; + #address-cells = <1>; + #size-cells = <1>; + partition@0 { /* 768KB */ + label = "u-boot"; + reg = <0 0xC0000>; + }; + partition@c0000 { /* 128KB */ + label = "env"; + reg = <0xc0000 0x20000>; + }; + partition@e0000 { /* 128KB */ + label = "envred"; + reg = <0xe0000 0x20000>; + }; + partition@100000 { /* 64512KB */ + label = "ubi0"; + reg = <0x100000 0x3F00000>; + }; + }; +}; diff --git a/arch/powerpc/dts/kmsupm5.dts b/arch/powerpc/dts/kmsupm5.dts new file mode 100644 index 0000000000..1cd11c3344 --- /dev/null +++ b/arch/powerpc/dts/kmsupm5.dts @@ -0,0 +1,129 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * ABB PGGA SUPM5 Device Tree Source + * + * Copyright (C) 2020 Heiko Schocher hs@denx.de + * + */ + +/dts-v1/; + +#include "km8321.dtsi" + +/ { + model = "SUPM5"; + compatible = "ABB,kmpbec8321"; + #address-cells = <1>; + #size-cells = <1>; + + aliases { + ethernet0 = &enet_piggy2; + serial0 = &serial0; + }; +}; + +&i2c0 { + mux@70 { + compatible = "nxp,pca9547"; + reg = <0x70>; + #address-cells = <1>; + #size-cells = <0>; + + i2c@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + /* Inventory EEPROM of the unit itself */ + ivm@50 { + label = "MAIN_CTRL"; + compatible = "dummy"; + reg = <0x50>; + }; + }; + + i2c@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + /* Temperature sensors */ + temp@49 { + label = "board"; + compatible = "national,lm75"; + reg = <0x49>; + }; + }; + }; +}; + +&par_io { + /* UCC5 as HDLC controller for ICN */ + pio_ucc5: ucc_pin@04 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 2 0 1 0 2 0 /* TxD0 */ + 2 8 2 0 2 0 /* RxD0 */ + 2 29 2 0 2 0 /* CTS */ + 3 30 2 0 1 0 /* ICN CLK */ + >; + }; + + /* UCC4 Piggy Ethernet */ + pio_ucc4: ucc_pin@03 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 3 4 3 0 2 0 /* MDIO */ + 3 5 1 0 2 0 /* MDC */ + + 1 18 1 0 1 0 /* TxD0 */ + 1 19 1 0 1 0 /* TxD1 */ + 1 22 2 0 1 0 /* RxD0 */ + 1 23 2 0 1 0 /* RxD1 */ + 1 26 2 0 1 0 /* RX_ER */ + 1 28 2 0 1 0 /* RX_DV */ + 1 30 1 0 1 0 /* TX_EN */ + 1 31 2 0 1 0 /* CRS */ + 3 10 2 0 3 0 /* UCC4_RMII_CLK (CLK17) */ + >; + }; + + pio_spi: spi_pin@01 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 3 0 3 0 1 0 /* SPI_MOSI (PD0, bi, f3) */ + 3 1 3 0 1 0 /* SPI_MISO (PD1, bi, f3) */ + 3 2 3 0 1 0 /* SPI_CLK (PD2, bi, f3) */ + >; + }; +}; + +&localbus { + ranges = <0 0 0xf0000000 0x04000000 /* LB 0 Flash (boot) */ + 1 0 0xe8000000 0x01000000 /* LB 1 PRIO1 and Piggy */ + 2 0 0xa0000000 0x10000000>; /* LB 2 LPXF */ + + flash@0,0 { + compatible = "cfi-flash"; + reg = <0 0x00000000 0x04000000>; + bank-width = <2>; + #address-cells = <1>; + #size-cells = <1>; + partition@0 { /* 768KB */ + label = "u-boot"; + reg = <0 0xC0000>; + }; + partition@c0000 { /* 128KB */ + label = "env"; + reg = <0xc0000 0x20000>; + }; + partition@e0000 { /* 128KB */ + label = "envred"; + reg = <0xe0000 0x20000>; + }; + partition@100000 { /* 64512KB */ + label = "ubi0"; + reg = <0x100000 0x3F00000>; + }; + }; +}; diff --git a/arch/powerpc/dts/kmtegr1.dts b/arch/powerpc/dts/kmtegr1.dts new file mode 100644 index 0000000000..c9b21cf500 --- /dev/null +++ b/arch/powerpc/dts/kmtegr1.dts @@ -0,0 +1,392 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * ABB PGGA TEGR1 Device Tree Source + * + * Copyright (C) 2020 Heiko Schocher hs@denx.de + * + */ + +/dts-v1/; + +/ { + model = "KMTEGR1"; + compatible = "ABB,kmpbec8309"; + #address-cells = <1>; + #size-cells = <1>; + + aliases { + ethernet0 = &enet_zynq; + ethernet1 = &enet_piggy2; + serial0 = &serial0; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + PowerPC,8309@0 { + device_type = "cpu"; + reg = <0x0>; + d-cache-line-size = <32>; // 32 bytes + i-cache-line-size = <32>; // 32 bytes + d-cache-size = <16384>; // L1, 16K + i-cache-size = <16384>; // L1, 16K + timebase-frequency = <66000000>; + bus-frequency = <264000000>; + clock-frequency = <264000000>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x10000000>; + }; + + soc: soc8309@e0000000 { + #address-cells = <1>; + #size-cells = <1>; + device_type = "soc"; + compatible = "simple-bus"; + ranges = <0x0 0xe0000000 0x00100000>; + reg = <0xe0000000 0x00000200>; + bus-frequency = <264000000>; + + i2c@3000 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + compatible = "fsl,mpc8313-i2c","fsl-i2c"; + reg = <0x3000 0x100>; + interrupts = <14 0x8>; + interrupt-parent = <&ipic>; + clock-frequency = <400000>; + + mux@70 { + compatible = "nxp,pca9547"; + reg = <0x70>; + #address-cells = <1>; + #size-cells = <0>; + + i2c@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + /* + * Inventory EEPROM of the + * unit itself + */ + ivm@50 { + label = "MAIN_CTRL"; + compatible = "dummy"; + reg = <0x50>; + }; + }; + + i2c@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + /* Temperature sensors */ + temp@48 { + label = "front"; + compatible = "national,lm75"; + reg = <0x48>; + }; + + temp@49 { + label = "board"; + compatible = "national,lm75"; + reg = <0x49>; + }; + + temp@4a { + label = "power"; + compatible = "national,lm75"; + reg = <0x4a>; + }; + + temp@4b { + label = "bottom"; + compatible = "national,lm75"; + reg = <0x4b>; + }; + }; + + i2c@6 { + reg = <6>; + #address-cells = <1>; + #size-cells = <0>; + + }; + + i2c@5 { + reg = <5>; + #address-cells = <1>; + #size-cells = <0>; + + }; + + i2c@7 { + reg = <7>; + #address-cells = <1>; + #size-cells = <0>; + + }; + + i2c@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + + }; + }; + }; + + serial0: serial@4500 { + cell-index = <0>; + device_type = "serial"; + compatible = "fsl,ns16550", "ns16550"; + reg = <0x4500 0x100>; + clock-frequency = <264000000>; + interrupts = <9 0x8>; + interrupt-parent = <&ipic>; + }; + + dma@82a8 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8309-dma", "fsl,elo-dma"; + reg = <0x82a8 4>; + ranges = <0 0x8100 0x1a8>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + cell-index = <0>; + dma-channel@0 { + compatible = "fsl,mpc8309-dma-channel", + "fsl,elo-dma-channel"; + reg = <0 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + dma-channel@80 { + compatible = "fsl,mpc8309-dma-channel", + "fsl,elo-dma-channel"; + reg = <0x80 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + dma-channel@100 { + compatible = "fsl,mpc8309-dma-channel", + "fsl,elo-dma-channel"; + reg = <0x100 0x80>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + dma-channel@180 { + compatible = "fsl,mpc8309-dma-channel", + "fsl,elo-dma-channel"; + reg = <0x180 0x28>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + }; + }; + + ipic: pic@700 { + #address-cells = <0>; + #interrupt-cells = <2>; + compatible = "fsl,pq2pro-pic", "fsl,ipic"; + interrupt-controller; + reg = <0x700 0x100>; + device_type = "ipic"; + }; + + gpio1: gpio-controller@c00 { + #gpio-cells = <2>; + compatible = "fsl,mpc8309-gpio", "fsl,mpc8349-gpio"; + reg = <0xc00 0x100>; + interrupts = <75 0x8>; + interrupt-parent = <&ipic>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio2: gpio-controller@d00 { + #gpio-cells = <2>; + compatible = "fsl,mpc8309-gpio", "fsl,mpc8349-gpio"; + reg = <0xd00 0x100>; + interrupts = <75 0x8>; + interrupt-parent = <&ipic>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; + + spi@7000 { + cell-index = <0>; + compatible = "fsl,spi"; + reg = <0x7000 0x1000>; + interrupts = <16 0x8>; + interrupt-parent = <&ipic>; + mode = "cpu"; + #address-cells = <1>; + #size-cells = <0>; + + /* GPIO_15 chipselect for ZYNQ flash */ + gpios = <&gpio1 15 0>; + + zynq_flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,m25p80"; + reg = <0>; + spi-max-frequency = <4000000>; + m25p,fast-read; + partition@0 { + label = "bootloader"; + reg = <0x0 0x01000000>; + }; + }; + }; + }; + + qe: qe@e0100000 { + #address-cells = <1>; + #size-cells = <1>; + device_type = "qe"; + compatible = "fsl,qe"; + ranges = <0x0 0xe0100000 0x00100000>; + reg = <0xe0100000 0x480>; + brg-frequency = <0>; + bus-frequency = <396000000>; + fsl,qe-num-snums = <32>; + + muram@10000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,qe-muram", "fsl,cpm-muram"; + ranges = <0x0 0x00010000 0x00004000>; + + data-only@0 { + compatible = "fsl,qe-muram-data", + "fsl,cpm-muram-data"; + reg = <0x0 0x4000>; + }; + }; + + /* ZYNQ (UCC1, MDIO 0x10, MII) */ + enet_zynq: ethernet@2000 { + device_type = "network"; + compatible = "ucc_geth"; + cell-index = <1>; + reg = <0x2000 0x200>; + interrupts = <32>; + interrupt-parent = <&qeic>; + local-mac-address = [ 00 00 00 00 00 00 ]; + /*id=0, full-dup, 100M, no-pause, no-asym_p*/ + fixed-link = <0 1 100 0 0>; + rx-clock-name = "clk9"; + tx-clock-name = "clk10"; + phy-connection-type = "mii"; + }; + + /* Piggy2 (UCC3, MDIO 0x00, RMII) */ + enet_piggy2: ucc@2200 { + device_type = "network"; + compatible = "ucc_geth"; + cell-index = <3>; + reg = <0x2200 0x200>; + interrupts = <34>; + interrupt-parent = <&qeic>; + local-mac-address = [ 00 00 00 00 00 00 ]; + rx-clock-name = "none"; + tx-clock-name = "clk12"; + phy-handle = <&phy_piggy2>; + phy-connection-type = "rmii"; + }; + + mdio@2320 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x2320 0x38>; + compatible = "fsl,ucc-mdio"; + + /* Piggy2 (UCC3, MDIO 0x00, RMII) */ + phy_piggy2: ethernet-phy@0 { + reg = <0x0>; + device_type = "ethernet-phy"; + }; + + /* Explicitly set the tbi-phy to a non-zero address + * so that it does not conflict with phy_piggy2 that + * is unfortunately at address 0 + */ + tbi1: tbi-phy@1 { + reg = <0x1>; + device_type = "tbi-phy"; + }; + }; + + qeic: interrupt-controller@80 { + interrupt-controller; + compatible = "fsl,qe-ic"; + #address-cells = <0>; + #interrupt-cells = <1>; + reg = <0x80 0x80>; + big-endian; + interrupts = <32 8 33 8>; + interrupt-parent = <&ipic>; + }; + bootcount@0x13ff8 { + device_type = "bootcount"; + compatible = "u-boot,bootcount"; + reg = <0x13ff8 0x08>; + }; + + }; + localbus@e0005000 { + #address-cells = <2>; + #size-cells = <1>; + compatible = "fsl,mpc8309-localbus", "fsl,pq2pro-localbus", + "simple-bus"; + reg = <0xe0005000 0xd8>; + ranges = <0 0 0xf0000000 0x04000000 + 1 0 0xe8000000 0x01000000 + 2 0 0xe0000000 0x10000000 + 3 0 0xb0000000 0x10000000>; + + flash@0,0 { + compatible = "cfi-flash"; + reg = <0 0x00000000 0x04000000>; + bank-width = <2>; + nornand = "nor"; + #address-cells = <1>; + #size-cells = <1>; + use-advanced-sector-protection; + partition@0 { /* 768KB */ + label = "u-boot"; + reg = <0 0xc0000>; + }; + partition@c0000 { /* 256KB */ + label = "qe-fw"; + reg = <0xc0000 0x40000>; + }; + partition@100000 { /* 128KB */ + label = "env"; + reg = <0x100000 0x20000>; + }; + partition@120000 { /* 128KB */ + label = "envred"; + reg = <0x120000 0x20000>; + }; + partition@140000 { /* 64256KB */ + label = "ubi0"; + reg = <0x140000 0x3EC0000>; + }; + }; + }; +}; + +#include "km8309-uboot.dtsi" diff --git a/arch/powerpc/dts/kmtepr2.dts b/arch/powerpc/dts/kmtepr2.dts new file mode 100644 index 0000000000..5a272ec6cb --- /dev/null +++ b/arch/powerpc/dts/kmtepr2.dts @@ -0,0 +1,142 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * ABB PGGA TEPR2 Device Tree Source + * + * Copyright (C) 2020 Heiko Schocher hs@denx.de + * + */ + +/dts-v1/; + +#include "km8321.dtsi" + +/ { + model = "KMTEPR2"; + compatible = "ABB,kmpbec8321"; + #address-cells = <1>; + #size-cells = <1>; + + aliases { + ethernet0 = &enet_piggy2; + serial0 = &serial0; + }; +}; + +&i2c0 { + mux@70 { + compatible = "nxp,pca9547"; + reg = <0x70>; + #address-cells = <1>; + #size-cells = <0>; + + i2c@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + /* Inventory EEPROM of the unit itself */ + ivm@50 { + label = "MAIN_CTRL"; + compatible = "dummy"; + reg = <0x50>; + }; + }; + + i2c@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + /* Temperature sensors */ + temp@49 { + label = "board"; + compatible = "national,lm75"; + reg = <0x49>; + }; + + temp@4a { + label = "power"; + compatible = "national,lm75"; + reg = <0x4a>; + }; + }; + }; +}; + +&par_io { + /* UCC5 as HDLC controller for ICN */ + pio_ucc5: ucc_pin@04 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 2 0 1 0 2 0 /* TxD0 */ + 2 8 2 0 2 0 /* RxD0 */ + 2 29 2 0 2 0 /* CTS */ + 3 30 2 0 1 0 /* ICN CLK */ + >; + }; + + /* UCC4 Piggy Ethernet */ + pio_ucc4: ucc_pin@03 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 3 4 3 0 2 0 /* MDIO */ + 3 5 1 0 2 0 /* MDC */ + + 1 18 1 0 1 0 /* TxD0 */ + 1 19 1 0 1 0 /* TxD1 */ + 1 22 2 0 1 0 /* RxD0 */ + 1 23 2 0 1 0 /* RxD1 */ + 1 26 2 0 1 0 /* RX_ER */ + 1 28 2 0 1 0 /* RX_DV */ + 1 30 1 0 1 0 /* TX_EN */ + 1 31 2 0 1 0 /* CRS */ + 3 10 2 0 3 0 /* UCC4_RMII_CLK (CLK17) */ + >; + }; + + pio_spi: spi_pin@01 { + pio-map = < + /* + *port pin dir open_drain assignment has_irq + * SPI_MOSI (PD0, bi, f3) + */ + 3 0 3 0 1 0 + /* SPI_MISO (PD1, bi, f3) */ + 3 1 3 0 1 0 + /* SPI_CLK (PD2, bi, f3) */ + 3 2 3 0 1 0 + >; + }; +}; + +&localbus { + ranges = <0 0 0xf0000000 0x04000000 /* LB 0 Flash (boot) */ + 1 0 0xe8000000 0x01000000 /* LB 1 PRIO1 and Piggy */ + 2 0 0xa0000000 0x10000000 /* LB 2 NVSRAM */ + 3 0 0xb0000000 0x10000000>; /* LB 3 TEP2 */ + + flash@0,0 { + compatible = "cfi-flash"; + reg = <0 0x00000000 0x04000000>; + bank-width = <2>; + #address-cells = <1>; + #size-cells = <1>; + use-advanced-sector-protection; + partition@0 { /* 768KB */ + label = "u-boot"; + reg = <0 0xC0000>; + }; + partition@c0000 { /* 128KB */ + label = "env"; + reg = <0xc0000 0x20000>; + }; + partition@e0000 { /* 128KB */ + label = "envred"; + reg = <0xe0000 0x20000>; + }; + partition@100000 { /* 64512KB */ + label = "ubi0"; + reg = <0x100000 0x3F00000>; + }; + }; +}; diff --git a/arch/powerpc/dts/kmtuge1.dts b/arch/powerpc/dts/kmtuge1.dts new file mode 100644 index 0000000000..8a7b5a42cb --- /dev/null +++ b/arch/powerpc/dts/kmtuge1.dts @@ -0,0 +1,100 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * ABB PGGA TUGE1 Device Tree Source + * + * Copyright (C) 2020 Heiko Schocher hs@denx.de + * + */ + +/dts-v1/; + +#include "km8321.dtsi" + +/ { + model = "TUGE1"; + compatible = "ABB,kmpbec8321"; + #address-cells = <1>; + #size-cells = <1>; + + aliases { + ethernet0 = &enet_piggy2; + serial0 = &serial0; + }; +}; + +&par_io { + /* UCC5 as HDLC controller for ICN */ + pio_ucc5: ucc_pin@04 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 2 0 1 0 2 0 /* TxD0 */ + 2 8 2 0 2 0 /* RxD0 */ + 2 29 2 0 2 0 /* CTS */ + 3 30 2 0 1 0 /* ICN CLK */ + >; + }; + + /* UCC4 Piggy Ethernet */ + pio_ucc4: ucc_pin@03 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 3 4 3 0 2 0 /* MDIO */ + 3 5 1 0 2 0 /* MDC */ + + 1 18 1 0 1 0 /* TxD0 */ + 1 19 1 0 1 0 /* TxD1 */ + 1 22 2 0 1 0 /* RxD0 */ + 1 23 2 0 1 0 /* RxD1 */ + 1 26 2 0 1 0 /* RX_ER */ + 1 28 2 0 1 0 /* RX_DV */ + 1 30 1 0 1 0 /* TX_EN */ + 1 31 2 0 1 0 /* CRS */ + 3 10 2 0 3 0 /* UCC4_RMII_CLK (CLK17) */ + >; + }; + + pio_spi: spi_pin@01 { + pio-map = < + /* + *port pin dir open_drain assignment has_irq + * SPI_MOSI (PD0, bi, f3) + */ + 3 0 3 0 1 0 + /* SPI_MISO (PD1, bi, f3) */ + 3 1 3 0 1 0 + /* SPI_CLK (PD2, bi, f3) */ + 3 2 3 0 1 0 + >; + }; +}; + +&localbus { + ranges = <0 0 0xf0000000 0x04000000 /* LB 0 Flash (boot) */ + 1 0 0xe8000000 0x01000000 /* LB 1 PRIO1 and Piggy */ + 2 0 0xa0000000 0x10000000>; /* LB 2 PAXI */ + + flash@0,0 { + compatible = "cfi-flash"; + reg = <0 0x00000000 0x04000000>; + bank-width = <2>; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { /* 768KB */ + label = "u-boot"; + reg = <0 0xC0000>; + }; + partition@c0000 { /* 128KB */ + label = "env"; + reg = <0xc0000 0x20000>; + }; + partition@e0000 { /* 128KB */ + label = "envred"; + reg = <0xe0000 0x20000>; + }; + partition@100000 { /* 64512KB */ + label = "ubi0"; + reg = <0x100000 0x3F00000>; + }; + }; +}; diff --git a/arch/powerpc/dts/kmtuxa1.dts b/arch/powerpc/dts/kmtuxa1.dts new file mode 100644 index 0000000000..c2681c5efb --- /dev/null +++ b/arch/powerpc/dts/kmtuxa1.dts @@ -0,0 +1,100 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * ABB PGGA TUXA1 Device Tree Source + * + * Copyright (C) 2020 Heiko Schocher hs@denx.de + * + */ + +/dts-v1/; + +#include "km8321.dtsi" + +/ { + model = "TUXA1"; + compatible = "ABB,kmpbec8321"; + #address-cells = <1>; + #size-cells = <1>; + + aliases { + ethernet0 = &enet_piggy2; + serial0 = &serial0; + }; +}; + +&par_io { + /* UCC5 as HDLC controller for ICN */ + pio_ucc5: ucc_pin@04 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 2 0 1 0 2 0 /* TxD0 */ + 2 8 2 0 2 0 /* RxD0 */ + 2 29 2 0 2 0 /* CTS */ + 3 30 2 0 1 0 /* ICN CLK */ + >; + }; + + /* UCC4 Piggy Ethernet */ + pio_ucc4: ucc_pin@03 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 3 4 3 0 2 0 /* MDIO */ + 3 5 1 0 2 0 /* MDC */ + + 1 18 1 0 1 0 /* TxD0 */ + 1 19 1 0 1 0 /* TxD1 */ + 1 22 2 0 1 0 /* RxD0 */ + 1 23 2 0 1 0 /* RxD1 */ + 1 26 2 0 1 0 /* RX_ER */ + 1 28 2 0 1 0 /* RX_DV */ + 1 30 1 0 1 0 /* TX_EN */ + 1 31 2 0 1 0 /* CRS */ + 3 10 2 0 3 0 /* UCC4_RMII_CLK (CLK17) */ + >; + }; + + pio_spi: spi_pin@01 { + pio-map = < + /* + *port pin dir open_drain assignment has_irq + * SPI_MOSI (PD0, bi, f3) + */ + 3 0 3 0 1 0 + /* SPI_MISO (PD1, bi, f3) */ + 3 1 3 0 1 0 + /* SPI_CLK (PD2, bi, f3) */ + 3 2 3 0 1 0 + >; + }; +}; + +&localbus { + ranges = <0 0 0xf0000000 0x04000000 /* LB 0 Flash (boot) */ + 1 0 0xe8000000 0x01000000 /* LB 1 PRIO1 and Piggy */ + 2 0 0xa0000000 0x10000000 /* LB 2 LPXF */ + 3 0 0xb0000000 0x10000000>; /* LB 3 PINC2 */ + + flash@0,0 { + compatible = "cfi-flash"; + reg = <0 0x00000000 0x04000000>; + bank-width = <2>; + #address-cells = <1>; + #size-cells = <1>; + partition@0 { /* 768KB */ + label = "u-boot"; + reg = <0 0xC0000>; + }; + partition@c0000 { /* 128KB */ + label = "env"; + reg = <0xc0000 0x20000>; + }; + partition@e0000 { /* 128KB */ + label = "envred"; + reg = <0xe0000 0x20000>; + }; + partition@100000 { /* 64512KB */ + label = "ubi0"; + reg = <0x100000 0x3F00000>; + }; + }; +}; diff --git a/board/keymile/km83xx/Kconfig b/board/keymile/km83xx/Kconfig index 94075ce70f..bbafabdcb2 100644 --- a/board/keymile/km83xx/Kconfig +++ b/board/keymile/km83xx/Kconfig @@ -1,3 +1,20 @@ +menu "KM 83xx Options" + depends on MPC83xx + +config KM_ENABLE_FULL_DM_DTS_SUPPORT + bool "enable full DM/DTS support for KM 83xx boards" + default y + select CMD_DM + select DM + select DM_ETH + select DM_MDIO + select DM_SERIAL + select OF_CONTROL + select PINCTRL + select PINCTRL_QE + select PHYLIB +endmenu + if TARGET_KMETER1
config SYS_BOARD diff --git a/board/keymile/km83xx/MAINTAINERS b/board/keymile/km83xx/MAINTAINERS index 177c2c4970..0ce6317625 100644 --- a/board/keymile/km83xx/MAINTAINERS +++ b/board/keymile/km83xx/MAINTAINERS @@ -1,5 +1,6 @@ KM83XX BOARD M: Holger Brunck holger.brunck@ch.abb.com +M: Heiko Schocher hs@denx.de S: Maintained F: board/keymile/km83xx/ F: include/configs/km8360.h @@ -7,12 +8,24 @@ F: configs/kmcoge5ne_defconfig F: configs/kmeter1_defconfig F: include/configs/tuxx1.h F: configs/kmopti2_defconfig +F: configs/kmsupx5_defconfig F: configs/kmtepr2_defconfig F: configs/kmtegr1_defconfig F: configs/tuge1_defconfig F: configs/tuxx1_defconfig - -KMSUPX5 BOARD -M: Heiko Schocher hs@denx.de -S: Maintained -F: configs/kmsupx5_defconfig +F: arch/powerpc/dts/km8309-uboot.dtsi +F: arch/powerpc/dts/km8321-uboot.dtsi +F: arch/powerpc/dts/km8321.dtsi +F: arch/powerpc/dts/km836x-uboot.dtsi +F: arch/powerpc/dts/km836x.dtsi +F: arch/powerpc/dts/kmcoge5ne-uboot.dtsi +F: arch/powerpc/dts/kmcoge5ne.dts +F: arch/powerpc/dts/kmeter1-uboot.dtsi +F: arch/powerpc/dts/kmeter1.dts +F: arch/powerpc/dts/kmopti2.dts +F: arch/powerpc/dts/kmsupc5.dts +F: arch/powerpc/dts/kmsupm5.dts +F: arch/powerpc/dts/kmtegr1.dts +F: arch/powerpc/dts/kmtepr2.dts +F: arch/powerpc/dts/kmtuge1.dts +F: arch/powerpc/dts/kmtuxa1.dts diff --git a/board/keymile/km83xx/km83xx.c b/board/keymile/km83xx/km83xx.c index 75c558ad3c..a7923090db 100644 --- a/board/keymile/km83xx/km83xx.c +++ b/board/keymile/km83xx/km83xx.c @@ -36,70 +36,6 @@ DECLARE_GLOBAL_DATA_PTR;
static uchar ivm_content[CONFIG_SYS_IVM_EEPROM_MAX_LEN];
-const qe_iop_conf_t qe_iop_conf_tab[] = { - /* port pin dir open_drain assign */ -#if defined(CONFIG_ARCH_MPC8360) - /* MDIO */ - {0, 1, 3, 0, 2}, /* MDIO */ - {0, 2, 1, 0, 1}, /* MDC */ - - /* UCC4 - UEC */ - {1, 14, 1, 0, 1}, /* TxD0 */ - {1, 15, 1, 0, 1}, /* TxD1 */ - {1, 20, 2, 0, 1}, /* RxD0 */ - {1, 21, 2, 0, 1}, /* RxD1 */ - {1, 18, 1, 0, 1}, /* TX_EN */ - {1, 26, 2, 0, 1}, /* RX_DV */ - {1, 27, 2, 0, 1}, /* RX_ER */ - {1, 24, 2, 0, 1}, /* COL */ - {1, 25, 2, 0, 1}, /* CRS */ - {2, 15, 2, 0, 1}, /* TX_CLK - CLK16 */ - {2, 16, 2, 0, 1}, /* RX_CLK - CLK17 */ - - /* DUART - UART2 */ - {5, 0, 1, 0, 2}, /* UART2_SOUT */ - {5, 2, 1, 0, 1}, /* UART2_RTS */ - {5, 3, 2, 0, 2}, /* UART2_SIN */ - {5, 1, 2, 0, 3}, /* UART2_CTS */ -#elif !defined(CONFIG_ARCH_MPC8309) - /* Local Bus */ - {0, 16, 1, 0, 3}, /* LA00 */ - {0, 17, 1, 0, 3}, /* LA01 */ - {0, 18, 1, 0, 3}, /* LA02 */ - {0, 19, 1, 0, 3}, /* LA03 */ - {0, 20, 1, 0, 3}, /* LA04 */ - {0, 21, 1, 0, 3}, /* LA05 */ - {0, 22, 1, 0, 3}, /* LA06 */ - {0, 23, 1, 0, 3}, /* LA07 */ - {0, 24, 1, 0, 3}, /* LA08 */ - {0, 25, 1, 0, 3}, /* LA09 */ - {0, 26, 1, 0, 3}, /* LA10 */ - {0, 27, 1, 0, 3}, /* LA11 */ - {0, 28, 1, 0, 3}, /* LA12 */ - {0, 29, 1, 0, 3}, /* LA13 */ - {0, 30, 1, 0, 3}, /* LA14 */ - {0, 31, 1, 0, 3}, /* LA15 */ - - /* MDIO */ - {3, 4, 3, 0, 2}, /* MDIO */ - {3, 5, 1, 0, 2}, /* MDC */ - - /* UCC4 - UEC */ - {1, 18, 1, 0, 1}, /* TxD0 */ - {1, 19, 1, 0, 1}, /* TxD1 */ - {1, 22, 2, 0, 1}, /* RxD0 */ - {1, 23, 2, 0, 1}, /* RxD1 */ - {1, 26, 2, 0, 1}, /* RxER */ - {1, 28, 2, 0, 1}, /* Rx_DV */ - {1, 30, 1, 0, 1}, /* TxEN */ - {1, 31, 2, 0, 1}, /* CRS */ - {3, 10, 2, 0, 3}, /* TxCLK->CLK17 */ -#endif - - /* END of table */ - {0, 0, 0, 0, QE_IOP_TAB_END}, -}; - static int piggy_present(void) { struct km_bec_fpga __iomem *base = diff --git a/configs/kmcoge5ne_defconfig b/configs/kmcoge5ne_defconfig index 363099212e..2d7b7ba879 100644 --- a/configs/kmcoge5ne_defconfig +++ b/configs/kmcoge5ne_defconfig @@ -4,7 +4,6 @@ CONFIG_KM_DEF_NETDEV="eth1" CONFIG_ENV_SIZE=0x4000 CONFIG_ENV_SECT_SIZE=0x20000 CONFIG_BOOTCOUNT_BOOTLIMIT=3 -CONFIG_SYS_BOOTCOUNT_ADDR=0xE011BFF8 CONFIG_SYS_CLK_FREQ=66000000 CONFIG_MPC83xx=y CONFIG_HIGH_BATS=y @@ -156,7 +155,6 @@ CONFIG_ACR_PARKM_USB_I2C1_BOOT=y CONFIG_LCRR_DBYP_PLL_BYPASSED=y CONFIG_LCRR_EADC_2=y CONFIG_LCRR_CLKDIV_4=y -# CONFIG_SYS_MALLOC_F is not set CONFIG_OF_BOARD_SETUP=y CONFIG_OF_STDOUT_VIA_ALIAS=y CONFIG_MISC_INIT_R=y @@ -173,6 +171,7 @@ CONFIG_CMD_GREPENV=y CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y CONFIG_CMD_NAND=y +# CONFIG_CMD_PINMUX is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y @@ -182,11 +181,13 @@ CONFIG_MTDIDS_DEFAULT="nor0=boot,nand0=app" CONFIG_MTDPARTS_DEFAULT="mtdparts=boot:768k(u-boot),128k(env),128k(envred),-(ubi0);app:-(ubi1);" CONFIG_CMD_UBI=y # CONFIG_CMD_UBIFS is not set +CONFIG_DEFAULT_DEVICE_TREE="kmcoge5ne" CONFIG_SYS_REDUNDAND_ENVIRONMENT=y CONFIG_ENV_ADDR=0xF00C0000 CONFIG_ENV_ADDR_REDUND=0xF00E0000 -CONFIG_DM=y CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_DM_BOOTCOUNT=y +CONFIG_BOOTCOUNT_MEM=y # CONFIG_MMC is not set CONFIG_MTD=y CONFIG_MTD_NOR_FLASH=y @@ -196,8 +197,10 @@ CONFIG_FLASH_CFI_MTD=y CONFIG_SYS_FLASH_PROTECTION=y CONFIG_SYS_FLASH_CFI=y CONFIG_MTD_RAW_NAND=y +CONFIG_DM_ETH_PHY=y +CONFIG_QE_UEC=y # CONFIG_PCI is not set +# CONFIG_PINCTRL_FULL is not set CONFIG_QE=y CONFIG_SYS_NS16550=y CONFIG_BCH=y -CONFIG_OF_LIBFDT=y diff --git a/configs/kmeter1_defconfig b/configs/kmeter1_defconfig index 97c75dc68c..8967ace2e1 100644 --- a/configs/kmeter1_defconfig +++ b/configs/kmeter1_defconfig @@ -4,7 +4,6 @@ CONFIG_KM_DEF_NETDEV="eth2" CONFIG_ENV_SIZE=0x4000 CONFIG_ENV_SECT_SIZE=0x20000 CONFIG_BOOTCOUNT_BOOTLIMIT=3 -CONFIG_SYS_BOOTCOUNT_ADDR=0xE011BFF8 CONFIG_SYS_CLK_FREQ=66000000 CONFIG_MPC83xx=y CONFIG_HIGH_BATS=y @@ -120,7 +119,6 @@ CONFIG_ACR_PARKM_USB_I2C1_BOOT=y CONFIG_LCRR_DBYP_PLL_BYPASSED=y CONFIG_LCRR_EADC_2=y CONFIG_LCRR_CLKDIV_4=y -# CONFIG_SYS_MALLOC_F is not set CONFIG_OF_BOARD_SETUP=y CONFIG_OF_STDOUT_VIA_ALIAS=y CONFIG_MISC_INIT_R=y @@ -136,6 +134,7 @@ CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y +# CONFIG_CMD_PINMUX is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y @@ -145,11 +144,13 @@ CONFIG_MTDIDS_DEFAULT="nor0=boot" CONFIG_MTDPARTS_DEFAULT="mtdparts=boot:768k(u-boot),128k(env),128k(envred),-(ubi0);" CONFIG_CMD_UBI=y # CONFIG_CMD_UBIFS is not set +CONFIG_DEFAULT_DEVICE_TREE="kmeter1" CONFIG_SYS_REDUNDAND_ENVIRONMENT=y CONFIG_ENV_ADDR=0xF00C0000 CONFIG_ENV_ADDR_REDUND=0xF00E0000 -CONFIG_DM=y CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_DM_BOOTCOUNT=y +CONFIG_BOOTCOUNT_MEM=y # CONFIG_MMC is not set CONFIG_MTD=y CONFIG_MTD_NOR_FLASH=y @@ -158,7 +159,8 @@ CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y CONFIG_FLASH_CFI_MTD=y CONFIG_SYS_FLASH_PROTECTION=y CONFIG_SYS_FLASH_CFI=y +CONFIG_DM_ETH_PHY=y +CONFIG_QE_UEC=y # CONFIG_PCI is not set CONFIG_QE=y CONFIG_SYS_NS16550=y -CONFIG_OF_LIBFDT=y diff --git a/configs/kmopti2_defconfig b/configs/kmopti2_defconfig index 4b0f0e7521..7059facf0e 100644 --- a/configs/kmopti2_defconfig +++ b/configs/kmopti2_defconfig @@ -3,7 +3,6 @@ CONFIG_SYS_TEXT_BASE=0xF0000000 CONFIG_ENV_SIZE=0x4000 CONFIG_ENV_SECT_SIZE=0x20000 CONFIG_BOOTCOUNT_BOOTLIMIT=3 -CONFIG_SYS_BOOTCOUNT_ADDR=0xE0113FF8 CONFIG_SYS_CLK_FREQ=66000000 CONFIG_MPC83xx=y CONFIG_HIGH_BATS=y @@ -139,7 +138,6 @@ CONFIG_ACR_APARK_MASTER=y CONFIG_ACR_PARKM_USB_I2C1_BOOT=y CONFIG_LCRR_EADC_1=y CONFIG_LCRR_CLKDIV_2=y -# CONFIG_SYS_MALLOC_F is not set CONFIG_OF_BOARD_SETUP=y CONFIG_OF_STDOUT_VIA_ALIAS=y CONFIG_MISC_INIT_R=y @@ -155,6 +153,7 @@ CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y +# CONFIG_CMD_PINMUX is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y @@ -164,11 +163,13 @@ CONFIG_MTDIDS_DEFAULT="nor0=boot" CONFIG_MTDPARTS_DEFAULT="mtdparts=boot:768k(u-boot),128k(env),128k(envred),-(ubi0);" CONFIG_CMD_UBI=y # CONFIG_CMD_UBIFS is not set +CONFIG_DEFAULT_DEVICE_TREE="kmopti2" CONFIG_SYS_REDUNDAND_ENVIRONMENT=y CONFIG_ENV_ADDR=0xF00C0000 CONFIG_ENV_ADDR_REDUND=0xF00E0000 -CONFIG_DM=y CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_DM_BOOTCOUNT=y +CONFIG_BOOTCOUNT_MEM=y # CONFIG_MMC is not set CONFIG_MTD=y CONFIG_MTD_NOR_FLASH=y @@ -177,7 +178,9 @@ CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y CONFIG_FLASH_CFI_MTD=y CONFIG_SYS_FLASH_PROTECTION=y CONFIG_SYS_FLASH_CFI=y +CONFIG_DM_ETH_PHY=y +CONFIG_QE_UEC=y # CONFIG_PCI is not set +# CONFIG_PINCTRL_FULL is not set CONFIG_QE=y CONFIG_SYS_NS16550=y -CONFIG_OF_LIBFDT=y diff --git a/configs/kmsupx5_defconfig b/configs/kmsupx5_defconfig index 2e8c2d32f2..d62fc84cf6 100644 --- a/configs/kmsupx5_defconfig +++ b/configs/kmsupx5_defconfig @@ -3,7 +3,6 @@ CONFIG_SYS_TEXT_BASE=0xF0000000 CONFIG_ENV_SIZE=0x4000 CONFIG_ENV_SECT_SIZE=0x20000 CONFIG_BOOTCOUNT_BOOTLIMIT=3 -CONFIG_SYS_BOOTCOUNT_ADDR=0xE0113FF8 CONFIG_SYS_CLK_FREQ=66000000 CONFIG_MPC83xx=y CONFIG_HIGH_BATS=y @@ -119,7 +118,6 @@ CONFIG_ACR_APARK_MASTER=y CONFIG_ACR_PARKM_USB_I2C1_BOOT=y CONFIG_LCRR_EADC_1=y CONFIG_LCRR_CLKDIV_2=y -# CONFIG_SYS_MALLOC_F is not set CONFIG_OF_BOARD_SETUP=y CONFIG_OF_STDOUT_VIA_ALIAS=y CONFIG_MISC_INIT_R=y @@ -144,11 +142,13 @@ CONFIG_MTDIDS_DEFAULT="nor0=boot" CONFIG_MTDPARTS_DEFAULT="mtdparts=boot:768k(u-boot),128k(env),128k(envred),-(ubi0);" CONFIG_CMD_UBI=y # CONFIG_CMD_UBIFS is not set +CONFIG_DEFAULT_DEVICE_TREE="kmsupm5" CONFIG_SYS_REDUNDAND_ENVIRONMENT=y CONFIG_ENV_ADDR=0xF00C0000 CONFIG_ENV_ADDR_REDUND=0xF00E0000 -CONFIG_DM=y CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_DM_BOOTCOUNT=y +CONFIG_BOOTCOUNT_MEM=y # CONFIG_MMC is not set CONFIG_MTD=y CONFIG_MTD_NOR_FLASH=y @@ -157,7 +157,9 @@ CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y CONFIG_FLASH_CFI_MTD=y CONFIG_SYS_FLASH_PROTECTION=y CONFIG_SYS_FLASH_CFI=y +CONFIG_DM_ETH_PHY=y +CONFIG_QE_UEC=y # CONFIG_PCI is not set +# CONFIG_PINCTRL_FULL is not set CONFIG_QE=y CONFIG_SYS_NS16550=y -CONFIG_OF_LIBFDT=y diff --git a/configs/kmtegr1_defconfig b/configs/kmtegr1_defconfig index dc09d238ec..5bb2b05e25 100644 --- a/configs/kmtegr1_defconfig +++ b/configs/kmtegr1_defconfig @@ -4,7 +4,6 @@ CONFIG_KM_DEF_NETDEV="eth1" CONFIG_ENV_SIZE=0x4000 CONFIG_ENV_SECT_SIZE=0x20000 CONFIG_BOOTCOUNT_BOOTLIMIT=3 -CONFIG_SYS_BOOTCOUNT_ADDR=0xE0113FF8 CONFIG_SYS_CLK_FREQ=66000000 CONFIG_MPC83xx=y CONFIG_HIGH_BATS=y @@ -118,7 +117,6 @@ CONFIG_ACR_APARK_MASTER=y CONFIG_ACR_PARKM_USB_I2C1_BOOT=y CONFIG_LCRR_EADC_1=y CONFIG_LCRR_CLKDIV_2=y -# CONFIG_SYS_MALLOC_F is not set CONFIG_OF_BOARD_SETUP=y CONFIG_OF_STDOUT_VIA_ALIAS=y CONFIG_SYS_EXTRA_OPTIONS="KMTEGR1" @@ -146,11 +144,13 @@ CONFIG_MTDPARTS_DEFAULT="mtdparts=boot:768k(u-boot),256k(qe-fw),128k(env),128k(e CONFIG_CMD_DIAG=y CONFIG_CMD_UBI=y # CONFIG_CMD_UBIFS is not set +CONFIG_DEFAULT_DEVICE_TREE="kmtegr1" CONFIG_SYS_REDUNDAND_ENVIRONMENT=y CONFIG_ENV_ADDR=0xF0100000 CONFIG_ENV_ADDR_REDUND=0xF0120000 -CONFIG_DM=y CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_DM_BOOTCOUNT=y +CONFIG_BOOTCOUNT_MEM=y # CONFIG_MMC is not set CONFIG_MTD=y CONFIG_MTD_NOR_FLASH=y @@ -160,9 +160,13 @@ CONFIG_FLASH_CFI_MTD=y CONFIG_SYS_FLASH_PROTECTION=y CONFIG_SYS_FLASH_CFI=y CONFIG_MTD_RAW_NAND=y +CONFIG_PHY_SMSC=y +CONFIG_PHY_FIXED=y +CONFIG_DM_ETH_PHY=y +CONFIG_QE_UEC=y # CONFIG_PCI is not set +# CONFIG_PINCTRL_FULL is not set CONFIG_QE=y CONFIG_SYS_QE_FMAN_FW_IN_NOR=y CONFIG_SYS_NS16550=y CONFIG_BCH=y -CONFIG_OF_LIBFDT=y diff --git a/configs/kmtepr2_defconfig b/configs/kmtepr2_defconfig index 6159425bba..02888dd1d3 100644 --- a/configs/kmtepr2_defconfig +++ b/configs/kmtepr2_defconfig @@ -3,7 +3,6 @@ CONFIG_SYS_TEXT_BASE=0xF0000000 CONFIG_ENV_SIZE=0x4000 CONFIG_ENV_SECT_SIZE=0x20000 CONFIG_BOOTCOUNT_BOOTLIMIT=3 -CONFIG_SYS_BOOTCOUNT_ADDR=0xE0113FF8 CONFIG_SYS_CLK_FREQ=66000000 CONFIG_MPC83xx=y CONFIG_HIGH_BATS=y @@ -139,7 +138,6 @@ CONFIG_ACR_APARK_MASTER=y CONFIG_ACR_PARKM_USB_I2C1_BOOT=y CONFIG_LCRR_EADC_1=y CONFIG_LCRR_CLKDIV_2=y -# CONFIG_SYS_MALLOC_F is not set CONFIG_OF_BOARD_SETUP=y CONFIG_OF_STDOUT_VIA_ALIAS=y CONFIG_MISC_INIT_R=y @@ -164,11 +162,13 @@ CONFIG_MTDIDS_DEFAULT="nor0=boot" CONFIG_MTDPARTS_DEFAULT="mtdparts=boot:768k(u-boot),128k(env),128k(envred),-(ubi0);" CONFIG_CMD_UBI=y # CONFIG_CMD_UBIFS is not set +CONFIG_DEFAULT_DEVICE_TREE="kmtepr2" CONFIG_SYS_REDUNDAND_ENVIRONMENT=y CONFIG_ENV_ADDR=0xF00C0000 CONFIG_ENV_ADDR_REDUND=0xF00E0000 -CONFIG_DM=y CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_DM_BOOTCOUNT=y +CONFIG_BOOTCOUNT_MEM=y # CONFIG_MMC is not set CONFIG_MTD=y CONFIG_MTD_NOR_FLASH=y @@ -177,7 +177,9 @@ CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y CONFIG_FLASH_CFI_MTD=y CONFIG_SYS_FLASH_PROTECTION=y CONFIG_SYS_FLASH_CFI=y +CONFIG_DM_ETH_PHY=y +CONFIG_QE_UEC=y # CONFIG_PCI is not set +# CONFIG_PINCTRL_FULL is not set CONFIG_QE=y CONFIG_SYS_NS16550=y -CONFIG_OF_LIBFDT=y diff --git a/configs/tuge1_defconfig b/configs/tuge1_defconfig index 93ff5f0361..7ac97742c5 100644 --- a/configs/tuge1_defconfig +++ b/configs/tuge1_defconfig @@ -3,7 +3,6 @@ CONFIG_SYS_TEXT_BASE=0xF0000000 CONFIG_ENV_SIZE=0x4000 CONFIG_ENV_SECT_SIZE=0x20000 CONFIG_BOOTCOUNT_BOOTLIMIT=3 -CONFIG_SYS_BOOTCOUNT_ADDR=0xE0113FF8 CONFIG_SYS_CLK_FREQ=66000000 CONFIG_MPC83xx=y CONFIG_HIGH_BATS=y @@ -119,7 +118,6 @@ CONFIG_ACR_APARK_MASTER=y CONFIG_ACR_PARKM_USB_I2C1_BOOT=y CONFIG_LCRR_EADC_1=y CONFIG_LCRR_CLKDIV_2=y -# CONFIG_SYS_MALLOC_F is not set CONFIG_OF_BOARD_SETUP=y CONFIG_OF_STDOUT_VIA_ALIAS=y CONFIG_MISC_INIT_R=y @@ -144,11 +142,13 @@ CONFIG_MTDIDS_DEFAULT="nor0=boot" CONFIG_MTDPARTS_DEFAULT="mtdparts=boot:768k(u-boot),128k(env),128k(envred),-(ubi0);" CONFIG_CMD_UBI=y # CONFIG_CMD_UBIFS is not set +CONFIG_DEFAULT_DEVICE_TREE="kmtuge1" CONFIG_SYS_REDUNDAND_ENVIRONMENT=y CONFIG_ENV_ADDR=0xF00C0000 CONFIG_ENV_ADDR_REDUND=0xF00E0000 -CONFIG_DM=y CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_DM_BOOTCOUNT=y +CONFIG_BOOTCOUNT_MEM=y # CONFIG_MMC is not set CONFIG_MTD=y CONFIG_MTD_NOR_FLASH=y @@ -157,7 +157,9 @@ CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y CONFIG_FLASH_CFI_MTD=y CONFIG_SYS_FLASH_PROTECTION=y CONFIG_SYS_FLASH_CFI=y +CONFIG_DM_ETH_PHY=y +CONFIG_QE_UEC=y # CONFIG_PCI is not set +# CONFIG_PINCTRL_FULL is not set CONFIG_QE=y CONFIG_SYS_NS16550=y -CONFIG_OF_LIBFDT=y diff --git a/configs/tuxx1_defconfig b/configs/tuxx1_defconfig index 2e27dc6b3f..77ca2db57a 100644 --- a/configs/tuxx1_defconfig +++ b/configs/tuxx1_defconfig @@ -3,7 +3,6 @@ CONFIG_SYS_TEXT_BASE=0xF0000000 CONFIG_ENV_SIZE=0x4000 CONFIG_ENV_SECT_SIZE=0x20000 CONFIG_BOOTCOUNT_BOOTLIMIT=3 -CONFIG_SYS_BOOTCOUNT_ADDR=0xE0113FF8 CONFIG_SYS_CLK_FREQ=66000000 CONFIG_MPC83xx=y CONFIG_HIGH_BATS=y @@ -141,7 +140,6 @@ CONFIG_ACR_APARK_MASTER=y CONFIG_ACR_PARKM_USB_I2C1_BOOT=y CONFIG_LCRR_EADC_1=y CONFIG_LCRR_CLKDIV_2=y -# CONFIG_SYS_MALLOC_F is not set CONFIG_OF_BOARD_SETUP=y CONFIG_OF_STDOUT_VIA_ALIAS=y CONFIG_MISC_INIT_R=y @@ -166,11 +164,13 @@ CONFIG_MTDIDS_DEFAULT="nor0=boot" CONFIG_MTDPARTS_DEFAULT="mtdparts=boot:768k(u-boot),128k(env),128k(envred),-(ubi0);" CONFIG_CMD_UBI=y # CONFIG_CMD_UBIFS is not set +CONFIG_DEFAULT_DEVICE_TREE="kmtuxa1" CONFIG_SYS_REDUNDAND_ENVIRONMENT=y CONFIG_ENV_ADDR=0xF00C0000 CONFIG_ENV_ADDR_REDUND=0xF00E0000 -CONFIG_DM=y CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_DM_BOOTCOUNT=y +CONFIG_BOOTCOUNT_MEM=y # CONFIG_MMC is not set CONFIG_MTD=y CONFIG_MTD_NOR_FLASH=y @@ -179,7 +179,10 @@ CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y CONFIG_FLASH_CFI_MTD=y CONFIG_SYS_FLASH_PROTECTION=y CONFIG_SYS_FLASH_CFI=y +CONFIG_PHY_SMSC=y +CONFIG_DM_ETH_PHY=y +CONFIG_QE_UEC=y # CONFIG_PCI is not set +# CONFIG_PINCTRL_FULL is not set CONFIG_QE=y CONFIG_SYS_NS16550=y -CONFIG_OF_LIBFDT=y diff --git a/include/configs/km/km-mpc832x.h b/include/configs/km/km-mpc832x.h index d7186ab919..22dfb5da67 100644 --- a/include/configs/km/km-mpc832x.h +++ b/include/configs/km/km-mpc832x.h @@ -10,20 +10,6 @@ #define CONFIG_SYS_CLK_FREQ 66000000 #define CONFIG_83XX_PCICLK 66000000
-/* - * QE UEC ethernet configuration - */ -#define CONFIG_UEC_ETH1 /* GETH1 */ -#define UEC_VERBOSE_DEBUG 1 - -#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */ -#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ -#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17 -#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH -#define CONFIG_SYS_UEC1_PHY_ADDR 0 -#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII -#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 - /* * System IO Config */ diff --git a/include/configs/km/km-mpc8360.h b/include/configs/km/km-mpc8360.h index bdbb8bf6b5..798b126960 100644 --- a/include/configs/km/km-mpc8360.h +++ b/include/configs/km/km-mpc8360.h @@ -6,20 +6,6 @@ * High Level Configuration Options */
-/* - * QE UEC ethernet configuration - */ -#define CONFIG_UEC_ETH1 /* GETH1 */ -#define UEC_VERBOSE_DEBUG 1 - -#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */ -#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ -#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17 -#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH -#define CONFIG_SYS_UEC1_PHY_ADDR 0 -#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII -#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 - /* * System IO Setup */ diff --git a/include/configs/km/km-mpc83xx.h b/include/configs/km/km-mpc83xx.h index 451baf8b80..7d9012c715 100644 --- a/include/configs/km/km-mpc83xx.h +++ b/include/configs/km/km-mpc83xx.h @@ -61,16 +61,6 @@ #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-/* - * Serial Port - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) - /* I2C */ #define CONFIG_SYS_I2C #define CONFIG_SYS_NUM_I2C_BUSES 4