Thanks for the help from Spence. I applied patch, it's partially working. Actually I set REDUCED flag on interface, so the real problem should phy register 20. I originally I set it to 0x0ce2, the mac's speed is wrong. Thank you very much!
But it's only partially working now. I can ping out from my customized board to another PC NIC, but cannot ping from PC to my board. I noticed tsec_halt is call after calling ping, so maccfg1 is retored back to disable tx/rx, and phy is shutdown. Could this be the reason? I tried to remove tsec_halt, things become worse. Beside I can only ping one way, now it's only pingable from my board for the first time. Anyone has solution for this?
Regards,
- Reeve
On 10/27/06, Spence Nick-rxtd10 Nick.Spence@freescale.com wrote:
Try the following that was submitted as a patch for u-boot but has not yet been integrated:
[DNX#2006102042000014] Add Marvell Phy and RGMII support to eTSEC setup
This sets up the eTSEC and the Marvel Phy to support 10M, 100M and 1000M rates when configured in RGMII mode.
drivers/tsec.c | 8 ++++---- 1 files changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/tsec.c b/drivers/tsec.c index 7ec565c..6cc6444 100644 --- a/drivers/tsec.c +++ b/drivers/tsec.c @@ -583,11 +583,10 @@ static void adjust_link(struct eth_devic regs->maccfg2 = ((regs->maccfg2&~(MACCFG2_IF)) | MACCFG2_MII);
/* If We're in reduced mode, we need* to say whether we're 10 or 100 MB.
/* Set R100 bit in all modes although* it is only used in RGMII mode */
if ((priv->speed == 100)&& (priv->flags & TSEC_REDUCED))
if (priv->speed == 100) regs->ecntrl |= ECNTRL_R100; else regs->ecntrl &= ~(ECNTRL_R100);@@ -785,6 +784,7 @@ struct phy_info phy_info_M88E1111S = { {0x1d, 0x5, NULL}, {0x1e, 0x0, NULL}, {0x1e, 0x100, NULL},
{0x14, 0x0cd2, NULL}, /* Add delay to RGMII TX and RX */ {MIIM_GBIT_CONTROL, MIIM_GBIT_CONTROL_INIT, NULL}, {MIIM_ANAR, MIIM_ANAR_INIT, NULL}, {MIIM_CONTROL, MIIM_CONTROL_RESET, NULL},-- 1.4.2.3
From: u-boot-users-bounces@lists.sourceforge.net[mailto:u-boot-users-bounces@lists.sourceforge.net] On Behalf Of Reeve Yang
Sent: Thursday, October 26, 2006 7:31 PM To: u-boot-users@lists.sourceforge.net Subject: [U-Boot-Users] tsec help Hello, My cpu is MPC8343E with dual tsec, phy is marvell 88E1111S. Nowthe physical link is up, but I just cannot ping. I printed some debug message about maccfg1/2 registers:
=> ping 192.168.1.1 tsec_halt Trying TSEC0 tsec_halt Speed: 100, full duplex TSEC0: maccfg2 = 0x7205 TSEC0: maccfg1 = 0xf Using TSEC0 device tsec_halt ping failed; host 192.168.1.1 is not alive I checked the MAC transmi counter register there are packetssending out, but no packet on the wire. The PHY is hard wired into RGMII to copper mode. Could anyone who has done similiar work point to where the problem is? Where to look at?
Regards, - Reeve