From: Vadim Bendebury vbendeb@chromium.org
The initialization table comes from the "Illustration of I2C command for initialing PS8625" document supplied by Parade.
Signed-off-by: Vadim Bendebury vbendeb@chromium.org Signed-off-by: Ajay Kumar ajaykumar.rs@samsung.com Acked-by: Simon Glass sjg@chromium.org Tested-by: Simon Glass sjg@chromium.org --- drivers/video/Makefile | 1 + drivers/video/parade.c | 220 ++++++++++++++++++++++++++++++++++++++++++++++++ include/fdtdec.h | 1 + lib/fdtdec.c | 1 + 4 files changed, 223 insertions(+) create mode 100644 drivers/video/parade.c
diff --git a/drivers/video/Makefile b/drivers/video/Makefile index 93a91c3..248aa35 100644 --- a/drivers/video/Makefile +++ b/drivers/video/Makefile @@ -42,3 +42,4 @@ obj-$(CONFIG_VIDEO_TEGRA) += tegra.o obj-$(CONFIG_VIDEO_VCXK) += bus_vcxk.o obj-$(CONFIG_FORMIKE) += formike.o obj-$(CONFIG_AM335X_LCD) += am335x-fb.o +obj-$(CONFIG_VIDEO_PARADE) += parade.o diff --git a/drivers/video/parade.c b/drivers/video/parade.c new file mode 100644 index 0000000..0f543f6 --- /dev/null +++ b/drivers/video/parade.c @@ -0,0 +1,220 @@ +/* + * Copyright (c) 2014 The Chromium OS Authors. All rights reserved. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * This file is a driver for Parade dP<->LVDS bridges. The original submission + * is for the ps8625 chip. + */ +#include <config.h> +#include <common.h> +#include <i2c.h> +#include <fdtdec.h> + +/* + * Initialization of the chip is a process of writing certaing values into + * certain registers over i2c bus. The chip in fact responds to a range of + * addresses on the i2c bus, so for each written value three parameters are + * required: i2c address, register address and the actual value. + * + * The base address is derived from the device tree, only address offset is + * stored in the table below. + */ +/** + * struct reg_data() - data for a parade register write + * + * @addr_off offset from the i2c base address for parade + * @reg_addr register address to write + * @value value to be written + */ +struct reg_data { + uint8_t addr_off; + uint8_t reg; + uint8_t value; +} _packed; + +#define END_OF_TABLE 0xff /* Ficticious offset */ + +static const struct reg_data parade_values[] = { + {0x02, 0xa1, 0x01}, /* HPD low */ + /* + * SW setting + * [1:0] SW output 1.2V voltage is lower to 96% + */ + {0x04, 0x14, 0x01}, + /* + * RCO SS setting + * [5:4] = b01 0.5%, b10 1%, b11 1.5% + */ + {0x04, 0xe3, 0x20}, + {0x04, 0xe2, 0x80}, /* [7] RCO SS enable */ + /* + * RPHY Setting + * [3:2] CDR tune wait cycle before + * measure for fine tune b00: 1us, + * 01: 0.5us, 10:2us, 11:4us. + */ + {0x04, 0x8a, 0x0c}, + {0x04, 0x89, 0x08}, /* [3] RFD always on */ + /* + * CTN lock in/out: + * 20000ppm/80000ppm. Lock out 2 + * times. + */ + {0x04, 0x71, 0x2d}, + /* + * 2.7G CDR settings + * NOF=40LSB for HBR CDR setting + */ + {0x04, 0x7d, 0x07}, + {0x04, 0x7b, 0x00}, /* [1:0] Fmin=+4bands */ + {0x04, 0x7a, 0xfd}, /* [7:5] DCO_FTRNG=+-40% */ + /* + * 1.62G CDR settings + * [5:2]NOF=64LSB [1:0]DCO scale is 2/5 + */ + {0x04, 0xc0, 0x12}, + {0x04, 0xc1, 0x92}, /* Gitune=-37% */ + {0x04, 0xc2, 0x1c}, /* Fbstep=100% */ + {0x04, 0x32, 0x80}, /* [7] LOS signal disable */ + /* + * RPIO Setting + * [7:4] LVDS driver bias current : + * 75% (250mV swing) + */ + {0x04, 0x00, 0xb0}, + /* + * [7:6] Right-bar GPIO output strength is 8mA + */ + {0x04, 0x15, 0x40}, + /* EQ Training State Machine Setting */ + {0x04, 0x54, 0x10}, /* RCO calibration start */ + /* [4:0] MAX_LANE_COUNT set to one lane */ + {0x01, 0x02, 0x81}, + /* [4:0] LANE_COUNT_SET set to one lane */ + {0x01, 0x21, 0x81}, + {0x00, 0x52, 0x20}, + {0x00, 0xf1, 0x03}, /* HPD CP toggle enable */ + {0x00, 0x62, 0x41}, + /* Counter number, add 1ms counter delay */ + {0x00, 0xf6, 0x01}, + /* + * [6]PWM function control by + * DPCD0040f[7], default is PWM + * block always works. + */ + {0x00, 0x77, 0x06}, + /* + * 04h Adjust VTotal tolerance to + * fix the 30Hz no display issue + */ + {0x00, 0x4c, 0x04}, + /* DPCD00400='h00, Parade OUI = 'h001cf8 */ + {0x01, 0xc0, 0x00}, + {0x01, 0xc1, 0x1c}, /* DPCD00401='h1c */ + {0x01, 0xc2, 0xf8}, /* DPCD00402='hf8 */ + /* + * DPCD403~408 = ASCII code + * D2SLV5='h4432534c5635 + */ + {0x01, 0xc3, 0x44}, + {0x01, 0xc4, 0x32}, /* DPCD404 */ + {0x01, 0xc5, 0x53}, /* DPCD405 */ + {0x01, 0xc6, 0x4c}, /* DPCD406 */ + {0x01, 0xc7, 0x56}, /* DPCD407 */ + {0x01, 0xc8, 0x35}, /* DPCD408 */ + /* + * DPCD40A, Initial Code major revision + * '01' + */ + {0x01, 0xca, 0x01}, + /* DPCD40B, Initial Code minor revision '05' */ + {0x01, 0xcb, 0x05}, + /* DPCD720, Select internal PWM */ + {0x01, 0xa5, 0xa0}, + /* + * FFh for 100% PWM of brightness, 0h for 0% + * brightness + */ + {0x01, 0xa7, 0xff}, + /* + * Set LVDS output as 6bit-VESA mapping, + * single LVDS channel + */ + {0x01, 0xcc, 0x13}, + /* Enable SSC set by register */ + {0x02, 0xb1, 0x20}, + /* + * Set SSC enabled and +/-1% central + * spreading + */ + {0x04, 0x10, 0x16}, + /* MPU Clock source: LC => RCO */ + {0x04, 0x59, 0x60}, + {0x04, 0x54, 0x14}, /* LC -> RCO */ + {0x02, 0xa1, 0x91}, /* HPD high */ + {END_OF_TABLE} +}; + +/** + * Write values table into the Parade eDP bridge + * + * @return 0 on success, non-0 on failure + */ + +static int parade_write_regs(int base_addr, const struct reg_data *table) +{ + int ret = 0; + + while (!ret && (table->addr_off != END_OF_TABLE)) { + ret = i2c_write(base_addr + table->addr_off, + table->reg, 1, + (uint8_t *)&table->value, + sizeof(table->value)); + table++; + } + return ret; +} + +int parade_init(const void *blob) +{ + int bus, old_bus; + int parent; + int node; + int addr; + int ret; + + node = fdtdec_next_compatible(blob, 0, COMPAT_PARADE_PS8625); + if (node < 0) + return 0; + + parent = fdt_parent_offset(blob, node); + if (parent < 0) { + debug("%s: Could not find parent i2c node\n", __func__); + return -1; + } + addr = fdtdec_get_int(blob, node, "reg", -1); + if (addr < 0) { + debug("%s: Could not find i2c address\n", __func__); + return -1; + } + + bus = i2c_get_bus_num_fdt(parent); + old_bus = i2c_get_bus_num(); + + debug("%s: Using i2c bus %d\n", __func__, bus); + + /* + * TODO(sjg@chromium.org): Hmmm we seem to need some sort of delay + * here. + */ + mdelay(40); + i2c_set_bus_num(bus); + ret = parade_write_regs(addr, parade_values); + + i2c_set_bus_num(old_bus); + + return ret; +} diff --git a/include/fdtdec.h b/include/fdtdec.h index d883bd2..5f88938 100644 --- a/include/fdtdec.h +++ b/include/fdtdec.h @@ -95,6 +95,7 @@ enum fdt_compat_id { COMPAT_TI_TPS65090, /* Texas Instrument TPS65090 */ COMPAT_NXP_PTN3460, /* NXP PTN3460 DP/LVDS bridge */ COMPAT_SAMSUNG_EXYNOS_SYSMMU, /* Exynos sysmmu */ + COMPAT_PARADE_PS8625, /* Parade PS8622 EDP->LVDS bridge */
COMPAT_COUNT, }; diff --git a/lib/fdtdec.c b/lib/fdtdec.c index d95135d..c2f3645 100644 --- a/lib/fdtdec.c +++ b/lib/fdtdec.c @@ -71,6 +71,7 @@ static const char * const compat_names[COMPAT_COUNT] = { COMPAT(TI_TPS65090, "ti,tps65090"), COMPAT(COMPAT_NXP_PTN3460, "nxp,ptn3460"), COMPAT(SAMSUNG_EXYNOS_SYSMMU, "samsung,sysmmu-v3.3"), + COMPAT(PARADE_PS8625, "parade,ps8625"), };
const char *fdtdec_get_compatible(enum fdt_compat_id id)