Most Allwinner SoCs which use the so called "new timing mode" in their MMC controllers actually use the double-rate PLL6/PERIPH0 clock as their parent input clock. This is interestingly enough compensated by a hidden "by 2" post-divider in the mod clock, so the divider and actual output rate stay the same.
Even though for the H6 and H616 (but only for them!) we use the doubled input clock for the divider computation, we never accounted for the implicit post-divider, so the clock was only half the speed on those SoCs. This didn't really matter so far, as our slow MMIO routine limits the transfer speed anyway, but we will fix this soon.
Clean up the code around that selection, to always use the normal PLL6 (PERIPH0(1x)) clock as an input. As the rate and divider are the same, that makes no difference. Explain the hardware differences in a comment.
Signed-off-by: Andre Przywara andre.przywara@arm.com --- arch/arm/include/asm/arch-sunxi/clock_sun50i_h6.h | 2 +- drivers/mmc/sunxi_mmc.c | 10 +++++++--- 2 files changed, 8 insertions(+), 4 deletions(-)
diff --git a/arch/arm/include/asm/arch-sunxi/clock_sun50i_h6.h b/arch/arm/include/asm/arch-sunxi/clock_sun50i_h6.h index 62abfc4ef6b..e000f78ff45 100644 --- a/arch/arm/include/asm/arch-sunxi/clock_sun50i_h6.h +++ b/arch/arm/include/asm/arch-sunxi/clock_sun50i_h6.h @@ -326,7 +326,7 @@ struct sunxi_ccm_reg { #define CCM_MMC_CTRL_M(x) ((x) - 1) #define CCM_MMC_CTRL_N(x) ((x) << 8) #define CCM_MMC_CTRL_OSCM24 (0x0 << 24) -#define CCM_MMC_CTRL_PLL6X2 (0x1 << 24) +#define CCM_MMC_CTRL_PLL6 (0x1 << 24) #define CCM_MMC_CTRL_PLL_PERIPH2X2 (0x2 << 24) #define CCM_MMC_CTRL_ENABLE (0x1 << 31) /* H6 doesn't have these delays */ diff --git a/drivers/mmc/sunxi_mmc.c b/drivers/mmc/sunxi_mmc.c index 869af993d35..bc68debdad6 100644 --- a/drivers/mmc/sunxi_mmc.c +++ b/drivers/mmc/sunxi_mmc.c @@ -124,10 +124,14 @@ static int mmc_set_mod_clk(struct sunxi_mmc_priv *priv, unsigned int hz) #ifdef CONFIG_MACH_SUN9I pll = CCM_MMC_CTRL_PLL_PERIPH0; pll_hz = clock_get_pll4_periph0(); -#elif defined(CONFIG_SUN50I_GEN_H6) - pll = CCM_MMC_CTRL_PLL6X2; - pll_hz = clock_get_pll6() * 2; #else + /* + * SoCs since the A64 (H5, H6, H616) actually use the doubled + * rate of PLL6/PERIPH0 as an input clock, but compensate for + * that with a fixed post-divider of 2 in the mod clock. + * This cancels each other out, so for simplicity we just + * pretend it's always PLL6 without a post divider here. + */ pll = CCM_MMC_CTRL_PLL6; pll_hz = clock_get_pll6(); #endif