The Khadas vim2 derive from amlogic s912 reference design (Q200).
This patch moves the khadas-vim2 board support to a generic Q200 board, while keeping a dedicated defconfig to customize the names and device tree.
Signed-off-by: Neil Armstrong narmstrong@baylibre.com --- arch/arm/mach-meson/Kconfig | 9 +-- board/amlogic/khadas-vim2/Kconfig | 12 ---- board/amlogic/khadas-vim2/MAINTAINERS | 6 -- board/amlogic/khadas-vim2/Makefile | 6 -- board/amlogic/khadas-vim2/README | 103 -------------------------------- board/amlogic/khadas-vim2/khadas-vim2.c | 62 ------------------- board/amlogic/q200/Kconfig | 12 ++++ board/amlogic/q200/MAINTAINERS | 6 ++ board/amlogic/q200/Makefile | 6 ++ board/amlogic/q200/README.khadas-vim2 | 103 ++++++++++++++++++++++++++++++++ board/amlogic/q200/README.q200 | 102 +++++++++++++++++++++++++++++++ board/amlogic/q200/q200.c | 62 +++++++++++++++++++ configs/khadas-vim2_defconfig | 2 +- include/configs/khadas-vim2.h | 18 ------ include/configs/q200.h | 18 ++++++ 15 files changed, 315 insertions(+), 212 deletions(-) delete mode 100644 board/amlogic/khadas-vim2/Kconfig delete mode 100644 board/amlogic/khadas-vim2/MAINTAINERS delete mode 100644 board/amlogic/khadas-vim2/Makefile delete mode 100644 board/amlogic/khadas-vim2/README delete mode 100644 board/amlogic/khadas-vim2/khadas-vim2.c create mode 100644 board/amlogic/q200/Kconfig create mode 100644 board/amlogic/q200/MAINTAINERS create mode 100644 board/amlogic/q200/Makefile create mode 100644 board/amlogic/q200/README.khadas-vim2 create mode 100644 board/amlogic/q200/README.q200 create mode 100644 board/amlogic/q200/q200.c delete mode 100644 include/configs/khadas-vim2.h create mode 100644 include/configs/q200.h
diff --git a/arch/arm/mach-meson/Kconfig b/arch/arm/mach-meson/Kconfig index e0b2812..98303db 100644 --- a/arch/arm/mach-meson/Kconfig +++ b/arch/arm/mach-meson/Kconfig @@ -50,13 +50,14 @@ config TARGET_P212 You should also select this TARGET if you have Khadas Vim or a libretech aml-s905x-cc
-config TARGET_KHADAS_VIM2 +config TARGET_Q200 bool "KHADAS-VIM2" select MESON_GXM help - Khadas VIM2 is a single board computer based on Meson GXM + Q200 is a reference dessign board based on Meson GXM with 2/3 GiB of RAM, Ethernet, HDMI, 4 USB, micro-SD slot, - eMMC, IR receiver and a 40-pin GPIO header. + eMMC, IR receiver. + You should also select this TARGET if you have Khadas Vim2.
endchoice
@@ -72,6 +73,6 @@ source "board/amlogic/nanopi-k2/Kconfig"
source "board/amlogic/p212/Kconfig"
-source "board/amlogic/khadas-vim2/Kconfig" +source "board/amlogic/q200/Kconfig"
endif diff --git a/board/amlogic/khadas-vim2/Kconfig b/board/amlogic/khadas-vim2/Kconfig deleted file mode 100644 index d0af362..0000000 --- a/board/amlogic/khadas-vim2/Kconfig +++ /dev/null @@ -1,12 +0,0 @@ -if TARGET_KHADAS_VIM2 - -config SYS_BOARD - default "khadas-vim2" - -config SYS_VENDOR - default "amlogic" - -config SYS_CONFIG_NAME - default "khadas-vim2" - -endif diff --git a/board/amlogic/khadas-vim2/MAINTAINERS b/board/amlogic/khadas-vim2/MAINTAINERS deleted file mode 100644 index ca63e31..0000000 --- a/board/amlogic/khadas-vim2/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -KHADAS-VIM2 -M: Neil Armstrong narmstrong@baylibre.com -S: Maintained -F: board/amlogic/khadas-vim2/ -F: include/configs/khadas-vim2.h -F: configs/khadas-vim2_defconfig diff --git a/board/amlogic/khadas-vim2/Makefile b/board/amlogic/khadas-vim2/Makefile deleted file mode 100644 index 4e7c9a0..0000000 --- a/board/amlogic/khadas-vim2/Makefile +++ /dev/null @@ -1,6 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ -# -# (C) Copyright 2016 BayLibre, SAS -# Author: Neil Armstrong narmstrong@baylibre.com - -obj-y := khadas-vim2.o diff --git a/board/amlogic/khadas-vim2/README b/board/amlogic/khadas-vim2/README deleted file mode 100644 index 578693f..0000000 --- a/board/amlogic/khadas-vim2/README +++ /dev/null @@ -1,103 +0,0 @@ -U-Boot for Khadas VIM2 -======================= - -Khadas VIM2 is an Open Source DIY Box manufactured by Shenzhen Wesion -Technology Co., Ltd with the following specifications: - - - Amlogic S912 ARM Cortex-A53 octo-core SoC @ 1.5GHz - - ARM Mali T860 GPU - - 2/3GB DDR4 SDRAM - - 10/100/1000 Ethernet - - HDMI 2.0 4K/60Hz display - - 40-pin GPIO header - - 2 x USB 2.0 Host, 1 x USB 2.0 Type-C OTG - - 16GB/32GB/64GB eMMC - - 2MB SPI Flash - - microSD - - SDIO Wifi Module, Bluetooth - - Two channels IR receiver - -Currently the u-boot port supports the following devices: - - serial - - eMMC, microSD - - Ethernet - - I2C - - Regulators - - Reset controller - - Clock controller - - USB Host - - ADC - -U-Boot compilation -================== - - > export ARCH=arm - > export CROSS_COMPILE=aarch64-none-elf- - > make khadas-vim2_defconfig - > make - -Image creation -============== - -Amlogic doesn't provide sources for the firmware and for tools needed -to create the bootloader image, so it is necessary to obtain them from -the git tree published by the board vendor: - - > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-... - > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-... - > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz - > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz - > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH - > git clone https://github.com/khadas/u-boot -b Vim vim-u-boot - > cd vim-u-boot - > make kvim_defconfig - > make - > export FIPDIR=$PWD/fip - -Go back to mainline U-Boot source tree then : - > mkdir fip - - > cp $FIPDIR/gxl/bl2.bin fip/ - > cp $FIPDIR/gxl/acs.bin fip/ - > cp $FIPDIR/gxl/bl21.bin fip/ - > cp $FIPDIR/gxl/bl30.bin fip/ - > cp $FIPDIR/gxl/bl301.bin fip/ - > cp $FIPDIR/gxl/bl31.img fip/ - > cp u-boot.bin fip/bl33.bin - - > $FIPDIR/blx_fix.sh \ - fip/bl30.bin \ - fip/zero_tmp \ - fip/bl30_zero.bin \ - fip/bl301.bin \ - fip/bl301_zero.bin \ - fip/bl30_new.bin \ - bl30 - - > python $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0 - - > $FIPDIR/blx_fix.sh \ - fip/bl2_acs.bin \ - fip/zero_tmp \ - fip/bl2_zero.bin \ - fip/bl21.bin \ - fip/bl21_zero.bin \ - fip/bl2_new.bin \ - bl2 - - > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin - > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl31.img - > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl33.bin - > $FIPDIR/gxl/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig - > $FIPDIR/gxl/aml_encrypt_gxl --bootmk \ - --output fip/u-boot.bin \ - --bl2 fip/bl2.n.bin.sig \ - --bl30 fip/bl30_new.bin.enc \ - --bl31 fip/bl31.img.enc \ - --bl33 fip/bl33.bin.enc - -and then write the image to SD with: - - > DEV=/dev/your_sd_device - > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1 - > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444 diff --git a/board/amlogic/khadas-vim2/khadas-vim2.c b/board/amlogic/khadas-vim2/khadas-vim2.c deleted file mode 100644 index ff56569..0000000 --- a/board/amlogic/khadas-vim2/khadas-vim2.c +++ /dev/null @@ -1,62 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright (C) 2016 BayLibre, SAS - * Author: Neil Armstrong narmstrong@baylibre.com - */ - -#include <common.h> -#include <dm.h> -#include <environment.h> -#include <asm/io.h> -#include <asm/arch/gx.h> -#include <asm/arch/mem.h> -#include <asm/arch/sm.h> -#include <asm/arch/eth.h> - -#define EFUSE_SN_OFFSET 20 -#define EFUSE_SN_SIZE 16 -#define EFUSE_MAC_OFFSET 52 -#define EFUSE_MAC_SIZE 6 - -int board_init(void) -{ - return 0; -} - -int misc_init_r(void) -{ - u8 mac_addr[EFUSE_MAC_SIZE]; - char serial[EFUSE_SN_SIZE]; - ssize_t len; - - meson_gx_eth_init(PHY_INTERFACE_MODE_RGMII, 0); - - /* Reset PHY on GPIOZ_14 */ - clrbits_le32(GX_GPIO_EN(3), BIT(14)); - clrbits_le32(GX_GPIO_OUT(3), BIT(14)); - mdelay(10); - setbits_le32(GX_GPIO_OUT(3), BIT(14)); - - if (!eth_env_get_enetaddr("ethaddr", mac_addr)) { - len = meson_sm_read_efuse(EFUSE_MAC_OFFSET, - mac_addr, EFUSE_MAC_SIZE); - if (len == EFUSE_MAC_SIZE && is_valid_ethaddr(mac_addr)) - eth_env_set_enetaddr("ethaddr", mac_addr); - } - - if (!env_get("serial#")) { - len = meson_sm_read_efuse(EFUSE_SN_OFFSET, serial, - EFUSE_SN_SIZE); - if (len == EFUSE_SN_SIZE) - env_set("serial#", serial); - } - - return 0; -} - -int ft_board_setup(void *blob, bd_t *bd) -{ - meson_gx_init_reserved_memory(blob); - - return 0; -} diff --git a/board/amlogic/q200/Kconfig b/board/amlogic/q200/Kconfig new file mode 100644 index 0000000..cfaf379 --- /dev/null +++ b/board/amlogic/q200/Kconfig @@ -0,0 +1,12 @@ +if TARGET_Q200 + +config SYS_BOARD + default "q200" + +config SYS_VENDOR + default "amlogic" + +config SYS_CONFIG_NAME + default "q200" + +endif diff --git a/board/amlogic/q200/MAINTAINERS b/board/amlogic/q200/MAINTAINERS new file mode 100644 index 0000000..be86386 --- /dev/null +++ b/board/amlogic/q200/MAINTAINERS @@ -0,0 +1,6 @@ +Q200 +M: Neil Armstrong narmstrong@baylibre.com +S: Maintained +F: board/amlogic/q200/ +F: include/configs/q200.h +F: configs/khadas-vim2_defconfig diff --git a/board/amlogic/q200/Makefile b/board/amlogic/q200/Makefile new file mode 100644 index 0000000..fd78fd0 --- /dev/null +++ b/board/amlogic/q200/Makefile @@ -0,0 +1,6 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# (C) Copyright 2016 BayLibre, SAS +# Author: Neil Armstrong narmstrong@baylibre.com + +obj-y := q200.o diff --git a/board/amlogic/q200/README.khadas-vim2 b/board/amlogic/q200/README.khadas-vim2 new file mode 100644 index 0000000..578693f --- /dev/null +++ b/board/amlogic/q200/README.khadas-vim2 @@ -0,0 +1,103 @@ +U-Boot for Khadas VIM2 +======================= + +Khadas VIM2 is an Open Source DIY Box manufactured by Shenzhen Wesion +Technology Co., Ltd with the following specifications: + + - Amlogic S912 ARM Cortex-A53 octo-core SoC @ 1.5GHz + - ARM Mali T860 GPU + - 2/3GB DDR4 SDRAM + - 10/100/1000 Ethernet + - HDMI 2.0 4K/60Hz display + - 40-pin GPIO header + - 2 x USB 2.0 Host, 1 x USB 2.0 Type-C OTG + - 16GB/32GB/64GB eMMC + - 2MB SPI Flash + - microSD + - SDIO Wifi Module, Bluetooth + - Two channels IR receiver + +Currently the u-boot port supports the following devices: + - serial + - eMMC, microSD + - Ethernet + - I2C + - Regulators + - Reset controller + - Clock controller + - USB Host + - ADC + +U-Boot compilation +================== + + > export ARCH=arm + > export CROSS_COMPILE=aarch64-none-elf- + > make khadas-vim2_defconfig + > make + +Image creation +============== + +Amlogic doesn't provide sources for the firmware and for tools needed +to create the bootloader image, so it is necessary to obtain them from +the git tree published by the board vendor: + + > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-... + > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-... + > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz + > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz + > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH + > git clone https://github.com/khadas/u-boot -b Vim vim-u-boot + > cd vim-u-boot + > make kvim_defconfig + > make + > export FIPDIR=$PWD/fip + +Go back to mainline U-Boot source tree then : + > mkdir fip + + > cp $FIPDIR/gxl/bl2.bin fip/ + > cp $FIPDIR/gxl/acs.bin fip/ + > cp $FIPDIR/gxl/bl21.bin fip/ + > cp $FIPDIR/gxl/bl30.bin fip/ + > cp $FIPDIR/gxl/bl301.bin fip/ + > cp $FIPDIR/gxl/bl31.img fip/ + > cp u-boot.bin fip/bl33.bin + + > $FIPDIR/blx_fix.sh \ + fip/bl30.bin \ + fip/zero_tmp \ + fip/bl30_zero.bin \ + fip/bl301.bin \ + fip/bl301_zero.bin \ + fip/bl30_new.bin \ + bl30 + + > python $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0 + + > $FIPDIR/blx_fix.sh \ + fip/bl2_acs.bin \ + fip/zero_tmp \ + fip/bl2_zero.bin \ + fip/bl21.bin \ + fip/bl21_zero.bin \ + fip/bl2_new.bin \ + bl2 + + > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin + > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl31.img + > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl33.bin + > $FIPDIR/gxl/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig + > $FIPDIR/gxl/aml_encrypt_gxl --bootmk \ + --output fip/u-boot.bin \ + --bl2 fip/bl2.n.bin.sig \ + --bl30 fip/bl30_new.bin.enc \ + --bl31 fip/bl31.img.enc \ + --bl33 fip/bl33.bin.enc + +and then write the image to SD with: + + > DEV=/dev/your_sd_device + > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1 + > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444 diff --git a/board/amlogic/q200/README.q200 b/board/amlogic/q200/README.q200 new file mode 100644 index 0000000..55d730a --- /dev/null +++ b/board/amlogic/q200/README.q200 @@ -0,0 +1,102 @@ +U-Boot for Amlogic Q200 +======================= + +Q200 is a reference board manufactured by Amlogic with the following +specifications: + + - Amlogic S912 ARM Cortex-A53 octo-core SoC @ 1.5GHz + - ARM Mali T860 GPU + - 2/3GB DDR4 SDRAM + - 10/100/1000 Ethernet + - HDMI 2.0 4K/60Hz display + - 2 x USB 2.0 Host, 1 x USB 2.0 Device + - 16GB/32GB/64GB eMMC + - 2MB SPI Flash + - microSD + - SDIO Wifi Module, Bluetooth + - IR receiver + +Currently the u-boot port supports the following devices: + - serial + - eMMC, microSD + - Ethernet + - I2C + - Regulators + - Reset controller + - Clock controller + - USB Host + - ADC + +U-Boot compilation +================== + + > export ARCH=arm + > export CROSS_COMPILE=aarch64-none-elf- + > make khadas-vim2_defconfig + > make + +Image creation +============== + +Amlogic doesn't provide sources for the firmware and for tools needed +to create the bootloader image, so it is necessary to obtain them from +the git tree published by the board vendor: + + > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-... + > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-... + > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz + > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz + > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH + > git clone https://github.com/BayLibre/u-boot.git -b n-amlogic-openlinux-20170606 amlogic-u-boot + > cd amlogic-u-boot + > make gxm_q200_v1_defconfig + > make + > export FIPDIR=$PWD/fip + +Go back to mainline U-Boot source tree then : + > mkdir fip + + > cp $FIPDIR/gxl/bl2.bin fip/ + > cp $FIPDIR/gxl/acs.bin fip/ + > cp $FIPDIR/gxl/bl21.bin fip/ + > cp $FIPDIR/gxl/bl30.bin fip/ + > cp $FIPDIR/gxl/bl301.bin fip/ + > cp $FIPDIR/gxl/bl31.img fip/ + > cp u-boot.bin fip/bl33.bin + + > $FIPDIR/blx_fix.sh \ + fip/bl30.bin \ + fip/zero_tmp \ + fip/bl30_zero.bin \ + fip/bl301.bin \ + fip/bl301_zero.bin \ + fip/bl30_new.bin \ + bl30 + + > python $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0 + + > $FIPDIR/blx_fix.sh \ + fip/bl2_acs.bin \ + fip/zero_tmp \ + fip/bl2_zero.bin \ + fip/bl21.bin \ + fip/bl21_zero.bin \ + fip/bl2_new.bin \ + bl2 + + > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin + > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl31.img + > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl33.bin + > $FIPDIR/gxl/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig + > $FIPDIR/gxl/aml_encrypt_gxl --bootmk \ + --output fip/u-boot.bin \ + --bl2 fip/bl2.n.bin.sig \ + --bl30 fip/bl30_new.bin.enc \ + --bl31 fip/bl31.img.enc \ + --bl33 fip/bl33.bin.enc + +and then write the image to SD with: + + > DEV=/dev/your_sd_device + > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1 + > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444 diff --git a/board/amlogic/q200/q200.c b/board/amlogic/q200/q200.c new file mode 100644 index 0000000..ff56569 --- /dev/null +++ b/board/amlogic/q200/q200.c @@ -0,0 +1,62 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2016 BayLibre, SAS + * Author: Neil Armstrong narmstrong@baylibre.com + */ + +#include <common.h> +#include <dm.h> +#include <environment.h> +#include <asm/io.h> +#include <asm/arch/gx.h> +#include <asm/arch/mem.h> +#include <asm/arch/sm.h> +#include <asm/arch/eth.h> + +#define EFUSE_SN_OFFSET 20 +#define EFUSE_SN_SIZE 16 +#define EFUSE_MAC_OFFSET 52 +#define EFUSE_MAC_SIZE 6 + +int board_init(void) +{ + return 0; +} + +int misc_init_r(void) +{ + u8 mac_addr[EFUSE_MAC_SIZE]; + char serial[EFUSE_SN_SIZE]; + ssize_t len; + + meson_gx_eth_init(PHY_INTERFACE_MODE_RGMII, 0); + + /* Reset PHY on GPIOZ_14 */ + clrbits_le32(GX_GPIO_EN(3), BIT(14)); + clrbits_le32(GX_GPIO_OUT(3), BIT(14)); + mdelay(10); + setbits_le32(GX_GPIO_OUT(3), BIT(14)); + + if (!eth_env_get_enetaddr("ethaddr", mac_addr)) { + len = meson_sm_read_efuse(EFUSE_MAC_OFFSET, + mac_addr, EFUSE_MAC_SIZE); + if (len == EFUSE_MAC_SIZE && is_valid_ethaddr(mac_addr)) + eth_env_set_enetaddr("ethaddr", mac_addr); + } + + if (!env_get("serial#")) { + len = meson_sm_read_efuse(EFUSE_SN_OFFSET, serial, + EFUSE_SN_SIZE); + if (len == EFUSE_SN_SIZE) + env_set("serial#", serial); + } + + return 0; +} + +int ft_board_setup(void *blob, bd_t *bd) +{ + meson_gx_init_reserved_memory(blob); + + return 0; +} diff --git a/configs/khadas-vim2_defconfig b/configs/khadas-vim2_defconfig index f21e3a8..387d7da 100644 --- a/configs/khadas-vim2_defconfig +++ b/configs/khadas-vim2_defconfig @@ -2,7 +2,7 @@ CONFIG_ARM=y CONFIG_ARCH_MESON=y CONFIG_SYS_TEXT_BASE=0x01000000 CONFIG_MESON_GXM=y -CONFIG_TARGET_KHADAS_VIM2=y +CONFIG_TARGET_Q200=y CONFIG_DEBUG_UART_BASE=0xc81004c0 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_IDENT_STRING=" khadas-vim2" diff --git a/include/configs/khadas-vim2.h b/include/configs/khadas-vim2.h deleted file mode 100644 index 7ef8f42..0000000 --- a/include/configs/khadas-vim2.h +++ /dev/null @@ -1,18 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Configuration for Khadas VIM2 - * - * Copyright (C) 2017 Baylibre, SAS - * Author: Neil Armstrong narmstrong@baylibre.com - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_MISC_INIT_R - -#define MESON_FDTFILE_SETTING "fdtfile=amlogic/meson-gxm-khadas-vim2.dtb\0" - -#include <configs/meson-gx-common.h> - -#endif /* __CONFIG_H */ diff --git a/include/configs/q200.h b/include/configs/q200.h new file mode 100644 index 0000000..7ef8f42 --- /dev/null +++ b/include/configs/q200.h @@ -0,0 +1,18 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Configuration for Khadas VIM2 + * + * Copyright (C) 2017 Baylibre, SAS + * Author: Neil Armstrong narmstrong@baylibre.com + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_MISC_INIT_R + +#define MESON_FDTFILE_SETTING "fdtfile=amlogic/meson-gxm-khadas-vim2.dtb\0" + +#include <configs/meson-gx-common.h> + +#endif /* __CONFIG_H */