Revert commit 7a2c1b13 which dropped OpenRD boards. Assume maintainership of OpenRD. Switch OpenRD to generic board. Switch to Thumb build.
Signed-off-by: Albert ARIBAUD albert.u.boot@aribaud.net ---
Changes in v6: - revive OpenRD targets and assume maintainership - switch OpenRD to generic board and Thumb - fix checkpatch warning and checks
Changes in v5: None Changes in v4: None Changes in v3: None Changes in v2: None
arch/arm/mach-kirkwood/Kconfig | 4 + board/Marvell/openrd/Kconfig | 12 +++ board/Marvell/openrd/MAINTAINERS | 12 +++ board/Marvell/openrd/Makefile | 14 ++++ board/Marvell/openrd/kwbimage.cfg | 152 ++++++++++++++++++++++++++++++++++++ board/Marvell/openrd/openrd.c | 160 ++++++++++++++++++++++++++++++++++++++ board/Marvell/openrd/openrd.h | 30 +++++++ configs/openrd_base_defconfig | 7 ++ configs/openrd_client_defconfig | 7 ++ configs/openrd_ultimate_defconfig | 7 ++ include/configs/openrd.h | 140 +++++++++++++++++++++++++++++++++ 11 files changed, 545 insertions(+) create mode 100644 board/Marvell/openrd/Kconfig create mode 100644 board/Marvell/openrd/MAINTAINERS create mode 100644 board/Marvell/openrd/Makefile create mode 100644 board/Marvell/openrd/kwbimage.cfg create mode 100644 board/Marvell/openrd/openrd.c create mode 100644 board/Marvell/openrd/openrd.h create mode 100644 configs/openrd_base_defconfig create mode 100644 configs/openrd_client_defconfig create mode 100644 configs/openrd_ultimate_defconfig create mode 100644 include/configs/openrd.h
diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig index aab5d19..f7737bf 100644 --- a/arch/arm/mach-kirkwood/Kconfig +++ b/arch/arm/mach-kirkwood/Kconfig @@ -4,6 +4,9 @@ choice prompt "Marvell Kirkwood board select" optional
+config TARGET_OPENRD + bool "Marvell OpenRD Board" + config TARGET_DREAMPLUG bool "DreamPlug Board"
@@ -51,6 +54,7 @@ endchoice config SYS_SOC default "kirkwood"
+source "board/Marvell/openrd/Kconfig" source "board/Marvell/dreamplug/Kconfig" source "board/Marvell/guruplug/Kconfig" source "board/Marvell/sheevaplug/Kconfig" diff --git a/board/Marvell/openrd/Kconfig b/board/Marvell/openrd/Kconfig new file mode 100644 index 0000000..124b66d --- /dev/null +++ b/board/Marvell/openrd/Kconfig @@ -0,0 +1,12 @@ +if TARGET_OPENRD + +config SYS_BOARD + default "openrd" + +config SYS_VENDOR + default "Marvell" + +config SYS_CONFIG_NAME + default "openrd" + +endif diff --git a/board/Marvell/openrd/MAINTAINERS b/board/Marvell/openrd/MAINTAINERS new file mode 100644 index 0000000..3789a04 --- /dev/null +++ b/board/Marvell/openrd/MAINTAINERS @@ -0,0 +1,12 @@ +OPENRD BOARD +M: Albert ARIBAUD albert-u-boot@aribaud.net +S: Maintained +F: board/Marvell/openrd/ +F: include/configs/openrd.h +F: configs/openrd_base_defconfig + +OPENRD_CLIENT BOARD +M: Albert ARIBAUD albert-u-boot@aribaud.net +S: Maintained +F: configs/openrd_client_defconfig +F: configs/openrd_ultimate_defconfig diff --git a/board/Marvell/openrd/Makefile b/board/Marvell/openrd/Makefile new file mode 100644 index 0000000..8f95b79 --- /dev/null +++ b/board/Marvell/openrd/Makefile @@ -0,0 +1,14 @@ +# +# (C) Copyright 2009 +# Net Insight <www.netinsight.net> +# Written-by: Simon Kagstrom simon.kagstrom@netinsight.net +# +# Based on sheevaplug: +# (C) Copyright 2009 +# Marvell Semiconductor <www.marvell.com> +# Written-by: Prafulla Wadaskar prafulla@marvell.com +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := openrd.o diff --git a/board/Marvell/openrd/kwbimage.cfg b/board/Marvell/openrd/kwbimage.cfg new file mode 100644 index 0000000..8e59937 --- /dev/null +++ b/board/Marvell/openrd/kwbimage.cfg @@ -0,0 +1,152 @@ +# +# (C) Copyright 2009 +# Marvell Semiconductor <www.marvell.com> +# Written-by: Prafulla Wadaskar prafulla@marvell.com +# +# SPDX-License-Identifier: GPL-2.0+ +# +# Refer doc/README.kwbimage for more details about how-to configure +# and create kirkwood boot image +# + +# Boot Media configurations +BOOT_FROM nand +NAND_ECC_MODE default +NAND_PAGE_SIZE 0x0800 + +# SOC registers configuration using bootrom header extension +# Maximum KWBIMAGE_MAX_CONFIG configurations allowed + +# Configure RGMII-0 interface pad voltage to 1.8V +DATA 0xFFD100e0 0x1b1b1b9b + +#Dram initalization for SINGLE x16 CL=5 @ 400MHz +DATA 0xFFD01400 0x43000c30 # DDR Configuration register +# bit13-0: 0xc30 (3120 DDR2 clks refresh rate) +# bit23-14: zero +# bit24: 1= enable exit self refresh mode on DDR access +# bit25: 1 required +# bit29-26: zero +# bit31-30: 01 + +DATA 0xFFD01404 0x37543000 # DDR Controller Control Low +# bit 4: 0=addr/cmd in smame cycle +# bit 5: 0=clk is driven during self refresh, we don't care for APX +# bit 6: 0=use recommended falling edge of clk for addr/cmd +# bit14: 0=input buffer always powered up +# bit18: 1=cpu lock transaction enabled +# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 +# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM +# bit30-28: 3 required +# bit31: 0=no additional STARTBURST delay + +DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1) +# bit3-0: TRAS lsbs +# bit7-4: TRCD +# bit11- 8: TRP +# bit15-12: TWR +# bit19-16: TWTR +# bit20: TRAS msb +# bit23-21: 0x0 +# bit27-24: TRRD +# bit31-28: TRTP + +DATA 0xFFD0140C 0x00000a33 # DDR Timing (High) +# bit6-0: TRFC +# bit8-7: TR2R +# bit10-9: TR2W +# bit12-11: TW2W +# bit31-13: zero required + +DATA 0xFFD01410 0x000000cc # DDR Address Control +# bit1-0: 00, Cs0width=x8 +# bit3-2: 11, Cs0size=1Gb +# bit5-4: 00, Cs1width=x8 +# bit7-6: 11, Cs1size=1Gb +# bit9-8: 00, Cs2width=nonexistent +# bit11-10: 00, Cs2size =nonexistent +# bit13-12: 00, Cs3width=nonexistent +# bit15-14: 00, Cs3size =nonexistent +# bit16: 0, Cs0AddrSel +# bit17: 0, Cs1AddrSel +# bit18: 0, Cs2AddrSel +# bit19: 0, Cs3AddrSel +# bit31-20: 0 required + +DATA 0xFFD01414 0x00000000 # DDR Open Pages Control +# bit0: 0, OpenPage enabled +# bit31-1: 0 required + +DATA 0xFFD01418 0x00000000 # DDR Operation +# bit3-0: 0x0, DDR cmd +# bit31-4: 0 required + +DATA 0xFFD0141C 0x00000C52 # DDR Mode +# bit2-0: 2, BurstLen=2 required +# bit3: 0, BurstType=0 required +# bit6-4: 4, CL=5 +# bit7: 0, TestMode=0 normal +# bit8: 0, DLL reset=0 normal +# bit11-9: 6, auto-precharge write recovery ???????????? +# bit12: 0, PD must be zero +# bit31-13: 0 required + +DATA 0xFFD01420 0x00000042 # DDR Extended Mode +# bit0: 0, DDR DLL enabled +# bit1: 1, DDR drive strength reduced +# bit2: 0, DDR ODT control lsd (disabled) +# bit5-3: 000, required +# bit6: 1, DDR ODT control msb, (disabled) +# bit9-7: 000, required +# bit10: 0, differential DQS enabled +# bit11: 0, required +# bit12: 0, DDR output buffer enabled +# bit31-13: 0 required + +DATA 0xFFD01424 0x0000F17F # DDR Controller Control High +# bit2-0: 111, required +# bit3 : 1 , MBUS Burst Chop disabled +# bit6-4: 111, required +# bit7 : 0 +# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz +# bit9 : 0 , no half clock cycle addition to dataout +# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals +# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh +# bit15-12: 1111 required +# bit31-16: 0 required + +DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values) +DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values) + +DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 +DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size +# bit0: 1, Window enabled +# bit1: 0, Write Protect disabled +# bit3-2: 00, CS0 hit selected +# bit23-4: ones, required +# bit31-24: 0x0F, Size (i.e. 256MB) + +DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb +DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1 + +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled + +DATA 0xFFD01494 0x00120012 # DDR ODT Control (Low) +# bit3-0: 0010, (read) M_ODT[0] is asserted during read from DRAM CS1 +# bit7-4: 0001, (read) M_ODT[1] is asserted during read from DRAM CS0 +# bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1. +# bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0. +DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) + +DATA 0xFFD0149C 0x0000E40f # CPU ODT Control +# bit3-0: 1111, internal ODT is asserted during read from DRAM bank 0-3 +# bit11-10: 01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm +# bit13-12: 10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm +# bit14: 1, M_STARTBURST_IN ODT: Enabled +# bit15: 1, DDR IO ODT Unit: Use ODT block +DATA 0xFFD01480 0x00000001 # DDR Initialization Control +#bit0=1, enable DDR init upon this register write + +# End of Header extension +DATA 0x0 0x0 diff --git a/board/Marvell/openrd/openrd.c b/board/Marvell/openrd/openrd.c new file mode 100644 index 0000000..17a6560 --- /dev/null +++ b/board/Marvell/openrd/openrd.c @@ -0,0 +1,160 @@ +/* + * (C) Copyright 2009 + * Net Insight <www.netinsight.net> + * Written-by: Simon Kagstrom simon.kagstrom@netinsight.net + * + * Based on sheevaplug.c: + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Written-by: Prafulla Wadaskar prafulla@marvell.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <miiphy.h> +#include <asm/arch/cpu.h> +#include <asm/arch/soc.h> +#include <asm/arch/mpp.h> +#include "openrd.h" + +DECLARE_GLOBAL_DATA_PTR; + +int board_early_init_f(void) +{ + /* + * default gpio configuration + * There are maximum 64 gpios controlled through 2 sets of registers + * the below configuration configures mainly initial LED status + */ + mvebu_config_gpio(OPENRD_OE_VAL_LOW, + OPENRD_OE_VAL_HIGH, + OPENRD_OE_LOW, OPENRD_OE_HIGH); + + /* Multi-Purpose Pins Functionality configuration */ + static const u32 kwmpp_config[] = { + MPP0_NF_IO2, + MPP1_NF_IO3, + MPP2_NF_IO4, + MPP3_NF_IO5, + MPP4_NF_IO6, + MPP5_NF_IO7, + MPP6_SYSRST_OUTn, + MPP7_GPO, + MPP8_TW_SDA, + MPP9_TW_SCK, + MPP10_UART0_TXD, + MPP11_UART0_RXD, + MPP12_SD_CLK, + MPP13_SD_CMD, /* Alt UART1_TXD */ + MPP14_SD_D0, /* Alt UART1_RXD */ + MPP15_SD_D1, + MPP16_SD_D2, + MPP17_SD_D3, + MPP18_NF_IO0, + MPP19_NF_IO1, + MPP20_GE1_0, + MPP21_GE1_1, + MPP22_GE1_2, + MPP23_GE1_3, + MPP24_GE1_4, + MPP25_GE1_5, + MPP26_GE1_6, + MPP27_GE1_7, + MPP28_GPIO, + MPP29_TSMP9, + MPP30_GE1_10, + MPP31_GE1_11, + MPP32_GE1_12, + MPP33_GE1_13, + MPP34_GPIO, /* UART1 / SD sel */ + MPP35_TDM_CH0_TX_QL, + MPP36_TDM_SPI_CS1, + MPP37_TDM_CH2_TX_QL, + MPP38_TDM_CH2_RX_QL, + MPP39_AUDIO_I2SBCLK, + MPP40_AUDIO_I2SDO, + MPP41_AUDIO_I2SLRC, + MPP42_AUDIO_I2SMCLK, + MPP43_AUDIO_I2SDI, + MPP44_AUDIO_EXTCLK, + MPP45_TDM_PCLK, + MPP46_TDM_FS, + MPP47_TDM_DRX, + MPP48_TDM_DTX, + MPP49_TDM_CH0_RX_QL, + 0 + }; + + kirkwood_mpp_conf(kwmpp_config, NULL); + return 0; +} + +int board_init(void) +{ + /* + * arch number of board + */ +#if defined(CONFIG_BOARD_IS_OPENRD_BASE) + gd->bd->bi_arch_number = MACH_TYPE_OPENRD_BASE; +#elif defined(CONFIG_BOARD_IS_OPENRD_CLIENT) + gd->bd->bi_arch_number = MACH_TYPE_OPENRD_CLIENT; +#elif defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE) + gd->bd->bi_arch_number = MACH_TYPE_OPENRD_ULTIMATE; +#endif + + /* adress of boot parameters */ + gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; + return 0; +} + +#ifdef CONFIG_RESET_PHY_R +/* Configure and enable MV88E1116/88E1121 PHY */ +void mv_phy_init(char *name) +{ + u16 reg; + u16 devadr; + + if (miiphy_set_current_dev(name)) + return; + + /* command to read PHY dev address */ + if (miiphy_read(name, 0xEE, 0xEE, (u16 *)&devadr)) { + printf("Err..%s could not read PHY dev address\n", __func__); + return; + } + + /* + * Enable RGMII delay on Tx and Rx for CPU port + * Ref: sec 4.7.2 of chip datasheet + */ + miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2); + miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®); + reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); + miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg); + miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0); + + /* reset the phy */ + miiphy_reset(name, devadr); + + printf(PHY_NO" Initialized on %s\n", name); +} + +void reset_phy(void) +{ + mv_phy_init("egiga0"); + +#ifdef CONFIG_BOARD_IS_OPENRD_CLIENT + /* Kirkwood ethernet driver is written with the assumption that in case + * of multiple PHYs, their addresses are consecutive. But unfortunately + * in case of OpenRD-Client, PHY addresses are not consecutive.*/ + miiphy_write("egiga1", 0xEE, 0xEE, 24); +#endif + +#if defined(CONFIG_BOARD_IS_OPENRD_CLIENT) || \ + defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE) + /* configure and initialize both PHY's */ + mv_phy_init("egiga1"); +#endif +} +#endif /* CONFIG_RESET_PHY_R */ diff --git a/board/Marvell/openrd/openrd.h b/board/Marvell/openrd/openrd.h new file mode 100644 index 0000000..56dfeea --- /dev/null +++ b/board/Marvell/openrd/openrd.h @@ -0,0 +1,30 @@ +/* + * (C) Copyright 2009 + * Net Insight <www.netinsight.net> + * Written-by: Simon Kagstrom simon.kagstrom@netinsight.net + * + * Based on sheevaplug.h: + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Written-by: Prafulla Wadaskar prafulla@marvell.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __OPENRD_BASE_H +#define __OPENRD_BASE_H + +#define OPENRD_OE_LOW (~(1<<28)) /* RS232 / RS485 */ +#define OPENRD_OE_HIGH (~(1<<2)) /* SD / UART1 */ +#define OPENRD_OE_VAL_LOW (0) /* Sel RS232 */ +#define OPENRD_OE_VAL_HIGH (1 << 2) /* Sel SD */ + +/* PHY related */ +#define MV88E1116_LED_FCTRL_REG 10 +#define MV88E1116_CPRSP_CR3_REG 21 +#define MV88E1116_MAC_CTRL_REG 21 +#define MV88E1116_PGADR_REG 22 +#define MV88E1116_RGMII_TXTM_CTRL (1 << 4) +#define MV88E1116_RGMII_RXTM_CTRL (1 << 5) + +#endif /* __OPENRD_BASE_H */ diff --git a/configs/openrd_base_defconfig b/configs/openrd_base_defconfig new file mode 100644 index 0000000..1686139 --- /dev/null +++ b/configs/openrd_base_defconfig @@ -0,0 +1,7 @@ +CONFIG_ARM=y +CONFIG_KIRKWOOD=y +CONFIG_TARGET_OPENRD=y +CONFIG_SYS_EXTRA_OPTIONS="BOARD_IS_OPENRD_BASE" +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +# CONFIG_CMD_SETEXPR is not set diff --git a/configs/openrd_client_defconfig b/configs/openrd_client_defconfig new file mode 100644 index 0000000..c342315 --- /dev/null +++ b/configs/openrd_client_defconfig @@ -0,0 +1,7 @@ +CONFIG_ARM=y +CONFIG_KIRKWOOD=y +CONFIG_TARGET_OPENRD=y +CONFIG_SYS_EXTRA_OPTIONS="BOARD_IS_OPENRD_CLIENT" +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +# CONFIG_CMD_SETEXPR is not set diff --git a/configs/openrd_ultimate_defconfig b/configs/openrd_ultimate_defconfig new file mode 100644 index 0000000..530ba4d --- /dev/null +++ b/configs/openrd_ultimate_defconfig @@ -0,0 +1,7 @@ +CONFIG_ARM=y +CONFIG_KIRKWOOD=y +CONFIG_TARGET_OPENRD=y +CONFIG_SYS_EXTRA_OPTIONS="BOARD_IS_OPENRD_ULTIMATE" +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +# CONFIG_CMD_SETEXPR is not set diff --git a/include/configs/openrd.h b/include/configs/openrd.h new file mode 100644 index 0000000..d6b1393 --- /dev/null +++ b/include/configs/openrd.h @@ -0,0 +1,140 @@ +/* + * (C) Copyright 2009 + * Net Insight <www.netinsight.net> + * Written-by: Simon Kagstrom simon.kagstrom@netinsight.net + * + * Based on sheevaplug.h: + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Written-by: Prafulla Wadaskar prafulla@marvell.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _CONFIG_OPENRD_H +#define _CONFIG_OPENRD_H + +/* + * Version number information + */ +#ifdef CONFIG_BOARD_IS_OPENRD_ULTIMATE +# define CONFIG_IDENT_STRING "\nOpenRD-Ultimate" +#else +# ifdef CONFIG_BOARD_IS_OPENRD_CLIENT +# define CONFIG_IDENT_STRING "\nOpenRD-Client" +# else +# ifdef CONFIG_BOARD_IS_OPENRD_BASE +# define CONFIG_IDENT_STRING "\nOpenRD-Base" +# else +# error Unknown OpenRD board specified +# endif +# endif +#endif + +#define CONFIG_SYS_GENERIC_BOARD + +/* + * High Level Configuration Options (easy to change) + */ +#define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */ +#define CONFIG_KW88F6281 1 /* SOC Name */ +#define CONFIG_MACH_OPENRD_BASE /* Machine type */ +#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ +#define CONFIG_SYS_THUMB_BUILD + +/* + * Commands configuration + */ +#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ +#define CONFIG_SYS_MVFS +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_ENV +#define CONFIG_CMD_MII +#define CONFIG_CMD_MMC +#define CONFIG_CMD_NAND +#define CONFIG_CMD_PING +#define CONFIG_CMD_USB +#define CONFIG_CMD_IDE + +/* + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros + */ +#include "mv-common.h" + +/* + * Environment variables configurations + */ +#ifdef CONFIG_CMD_NAND +#define CONFIG_ENV_IS_IN_NAND 1 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */ +#else +#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */ +#endif +/* + * max 4k env size is enough, but in case of nand + * it has to be rounded to sector size + */ +#define CONFIG_ENV_SIZE 0x20000 /* 128k */ +#define CONFIG_ENV_ADDR 0x60000 +#define CONFIG_ENV_OFFSET 0x60000 /* env starts here */ +/* + * Environment is right behind U-Boot in flash. Make sure U-Boot + * doesn't grow into the environment area. + */ +#define CONFIG_BOARD_SIZE_LIMIT CONFIG_ENV_OFFSET + +/* + * Default environment variables + */ +#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \ + "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \ + "${x_bootcmd_usb}; bootm 0x6400000;" + +#define MTDIDS_DEFAULT "nand0=nand_mtd" +#define MTDPARTS_DEFAULT "mtdparts=nand_mtd:0x100000@0x000000(uboot),"\ + "0x400000@0x100000(uImage),"\ + "0x1fb00000@0x500000(rootfs)" + +#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \ + "=ttyS0,115200 "MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \ + "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \ + "x_bootcmd_usb=usb start\0" \ + "x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0" \ + "mtdids="MTDIDS_DEFAULT"\0" \ + "mtdparts="MTDPARTS_DEFAULT"\0" + +/* + * Ethernet Driver configuration + */ +#ifdef CONFIG_CMD_NET +# ifdef CONFIG_BOARD_IS_OPENRD_BASE +# define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ +# else +# define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */ +# endif +# ifdef CONFIG_BOARD_IS_OPENRD_ULTIMATE +# define CONFIG_PHY_BASE_ADR 0x0 +# define PHY_NO "88E1121" +# else +# define CONFIG_PHY_BASE_ADR 0x8 +# define PHY_NO "88E1116" +# endif +#endif /* CONFIG_CMD_NET */ + +/* + * SATA Driver configuration + */ +#ifdef CONFIG_MVSATA_IDE +#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET +#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET +#endif /*CONFIG_MVSATA_IDE*/ + +#ifdef CONFIG_CMD_MMC +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_MVEBU_MMC +#define CONFIG_SYS_MMC_BASE KW_SDIO_BASE +#endif /* CONFIG_CMD_MMC */ + +#endif /* _CONFIG_OPENRD_BASE_H */