More than likely it's just like the message says:
Error: start and/or end address not on sector boundary
and your not on a sector boundary.
Go into your include/config/"whateveryourboardiscalled.h" file and edit
#define CFG_ENV_ADDR #define CFG_ENV_SIZE #define CFG_ENV_SECT_SIZE
So that the enviornment starts and ends on a sector that is not inside u-boots code space and you should be kewl. It will need to take up a whole sector.
I don't completely know your system's memory map, but I'd guess
#define CFG_ENV_ADDR FE040000 #define CFG_ENV_SECT_SIZE 40000 #define CFG_ENV_SIZE CFG_ENV_SECT_SIZE
NZG.
On Monday 23 May 2005 07:09, v.sudeep@exgate.tek.com wrote:
Hello,
I am a newbie to U-Boot.
I am in the process of trying to load linux on the MPC8266ADS-PCI board. I compiled the u-boot code and flashed it in. The U-Boot comes up. But I am unable to save any of the environmental variables.
What should I be looking for ?? And what are the changes that I should be doing. Please suggest.
Details are as below.
- S u d e e p V
A system of morality which is based on relative emotional values is a mere illusion, a thoroughly vulgar conception which has nothing sound in it and nothing true. -Socrates.
After power on the initial u-boot prompt looks like this: => reset
U-Boot 1.1.2 (May 23 2005 - 14:24:36) MPC8260 Reset Status: Check Stop, External Soft, ExternalHard
MPC8260 Clock Configuration - Bus-to-Core Mult 3x, VCO Div 2, 60x Bus Freq 33-100,Core Freq 100-300 - dfbrg 0, corecnf 0x08, busdf 3, cpmdf 1, plldf 0, pllmf 1 - vco_out 264000000, scc_clk 66000000, brg_clk 66000000 - cpu_clk 198000000, cpm_clk 132000000, bus_clk 66000000 - pci_clk 66000000
CPU: MPC8260 (HiP4 Rev 14, Mask A.0(A) 2K25A) at 198 MHz Board: Motorola MPC8266ADS I2C: ready DRAM: SDRAM configuration read from SPD Size per side = 16MB Organization: 1 sides, 2 banks, 9 Columns, 11 Rows,Data width = 64 bits Refresh rate = 33, CAS latency = 2, Using Bank Based Interleave Total size: 16 MB FLASH: 8 MB *** Warning - bad CRC, using default environment
In: serial Out: serial Err: serial Net: FCC2 ETHERNET Hit any key to stop autoboot: 0 U-Boot 1.1.2 (May 23 2005 - 14:24:36) *** ERROR: `ethaddr' not set ## Booting image at 00100000 ... Bad Magic NumberNow => bdinfo memstart = 0x00000000 memsize = 0x01000000 flashstart = 0xFE000000 flashsize = 0x00800000 flashoffset = 0x00000000 sramstart = 0x00000000 sramsize = 0x00000000 immr_base = 0xF0000000 bootflags = 0x00000001 vco = 264 MHz sccfreq = 66 MHz brgfreq = 66 MHz intfreq = 198 MHz cpmfreq = 132 MHz busfreq = 66 MHz ethaddr = 00:00:00:00:00:00 IP addr = 0.0.0.0 baudrate = 115200 bps
=> flinfo Bank # 1: Sharp 28F016SC (16 Mbit, 32 x 64K) Size: 8 MB in 32 Sectors Sector Start Addresses: FE000000 FE040000 FE080000 FE0C0000FE100000 FE140000 FE180000 FE1C0000 FE200000 FE240000 FE280000 FE2C0000 FE300000 FE340000 FE380000 FE3C0000 FE400000 FE440000 FE480000 FE4C0000 FE500000 FE540000 FE580000 FE5C0000 FE600000 FE640000 FE680000 FE6C0000 FE700000 FE740000 FE780000 FE7C0000
=> printenv bootcmd=version;echo;bootp;setenv bootargs root=/dev/nfs rwnfsroot=$(serverip)mbootdelay=5 baudrate=115200 stdin=serial stdout=serial stderr=serial ethact=FCC2 ETHERNET
Environment size: 254/262140 bytes => saveenv Saving Environment to Flash... Error: start and/or end address not on sector boundary