The mPCIe slots on ClearFog Pro and ClearFog Base may be alternately configured for SATA usage.
Signed-off-by: Joel Johnson mrjoel@lixil.net Reviewed-by: Stefan Roese sr@denx.de
---
v2 changes: - fixed help indentation v3 changes: - none v4 changes: - adjust static SerDes configuration at runtime instead of #ifdef - add setting of swap_rx for SATA (as yet untested on hardware) v5 changes: - make independent of runtime detection v6 change: - remove code side double check of config consistency
--- board/solidrun/clearfog/Kconfig | 17 +++++++++++++++++ board/solidrun/clearfog/clearfog.c | 14 ++++++++++++++ 2 files changed, 31 insertions(+)
diff --git a/board/solidrun/clearfog/Kconfig b/board/solidrun/clearfog/Kconfig index c910e17093..44224d903d 100644 --- a/board/solidrun/clearfog/Kconfig +++ b/board/solidrun/clearfog/Kconfig @@ -15,6 +15,23 @@ config TARGET_CLEARFOG_BASE detection via additional EEPROM hardware. This option enables selecting the Base variant for older hardware revisions.
+config CLEARFOG_CON3_SATA + bool "Use CON3 slot in SATA mode" + help + Use the CON3 port with SATA protocol instead of the default PCIe. + The ClearFog port allows usage of either mSATA or miniPCIe + modules, but the desired protocol must be configured at build + time since it affects the SerDes topology layout. + +config CLEARFOG_CON2_SATA + bool "Use CON2 slot in SATA mode" + depends on !TARGET_CLEARFOG_BASE + help + Use the CON2 port with SATA protocol instead of the default PCIe. + The ClearFog port allows usage of either mSATA or miniPCIe + modules, but the desired protocol must be configured at build + time since it affects the SerDes topology layout. + config CLEARFOG_SFP_25GB bool "Enable 2.5 Gbps mode for SFP" help diff --git a/board/solidrun/clearfog/clearfog.c b/board/solidrun/clearfog/clearfog.c index 8f3e5dc6a3..fd9bd95a15 100644 --- a/board/solidrun/clearfog/clearfog.c +++ b/board/solidrun/clearfog/clearfog.c @@ -67,6 +67,20 @@ int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count) if (IS_ENABLED(CONFIG_CLEARFOG_SFP_25GB)) board_serdes_map[5].serdes_speed = SERDES_SPEED_3_125_GBPS;
+ if (IS_ENABLED(CONFIG_CLEARFOG_CON2_SATA)) { + board_serdes_map[4].serdes_type = SATA2; + board_serdes_map[4].serdes_speed = SERDES_SPEED_3_GBPS; + board_serdes_map[4].serdes_mode = SERDES_DEFAULT_MODE; + board_serdes_map[4].swap_rx = 1; + } + + if (IS_ENABLED(CONFIG_CLEARFOG_CON3_SATA)) { + board_serdes_map[2].serdes_type = SATA1; + board_serdes_map[2].serdes_speed = SERDES_SPEED_3_GBPS; + board_serdes_map[2].serdes_mode = SERDES_DEFAULT_MODE; + board_serdes_map[2].swap_rx = 1; + } + /* Apply runtime detection changes */ if (sr_product_is(&cf_tlv_data, "Clearfog GTR")) { board_serdes_map[0].serdes_type = PEX0;