This patch enables and initialises DWMMC for SMDK5250. Supports both FDT and non-FDT. This patch creates a new file 'exynos5-dt.c' meant for FDT support. exynos5-dt.c: This file shall contain all code which supports FDT. Any addition of FDT support for any module needs to be added in this file. smdk5250.c: This file shall contain the code which supports non-FDT. version. Any addition of non-FDT support for any module needs to be added in this file. May be, the file smdk5250.c can be removed in near future when non-FDT is not required.
The Makefile is updated to compile only one of the files exynos5-dt.c / smdk5250.c based on FDT configuration.
NOTE: Please note that all additions corresponding to FDT need to be added into the file exynos5-dt.c. At same time if non-FDT support is required then add the corresponding updations into smdk5250.c.
Changes from V1: 1)A new file 'exynos5-dt.c' is created meant for FDT support 2)Makefile is updated to compile only one of the files exynos5-dt.c / smdk5250.c based on FDT configuration
Changes from V2: 1)Updation of commit message and resubmition of proper patch set.
Signed-off-by: Amar amarendra.xt@samsung.com --- board/samsung/smdk5250/Makefile | 4 + board/samsung/smdk5250/exynos5-dt.c | 242 ++++++++++++++++++++++++++++++++++++ board/samsung/smdk5250/smdk5250.c | 97 +++++++-------- include/configs/exynos5250-dt.h | 2 + include/i2c.h | 2 + 5 files changed, 292 insertions(+), 55 deletions(-) create mode 100644 board/samsung/smdk5250/exynos5-dt.c
diff --git a/board/samsung/smdk5250/Makefile b/board/samsung/smdk5250/Makefile index 47c6a5a..ecca9f3 100644 --- a/board/samsung/smdk5250/Makefile +++ b/board/samsung/smdk5250/Makefile @@ -32,8 +32,12 @@ COBJS += tzpc_init.o COBJS += smdk5250_spl.o
ifndef CONFIG_SPL_BUILD +ifdef CONFIG_OF_CONTROL +COBJS += exynos5-dt.o +else COBJS += smdk5250.o endif +endif
ifdef CONFIG_SPL_BUILD COBJS += spl_boot.o diff --git a/board/samsung/smdk5250/exynos5-dt.c b/board/samsung/smdk5250/exynos5-dt.c new file mode 100644 index 0000000..da539ca --- /dev/null +++ b/board/samsung/smdk5250/exynos5-dt.c @@ -0,0 +1,242 @@ +/* + * Copyright (C) 2012 Samsung Electronics + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <fdtdec.h> +#include <asm/io.h> +#include <i2c.h> +#include <netdev.h> +#include <spi.h> +#include <asm/arch/cpu.h> +#include <asm/arch/dwmmc.h> +#include <asm/arch/gpio.h> +#include <asm/arch/mmc.h> +#include <asm/arch/pinmux.h> +#include <asm/arch/sromc.h> +#include <power/pmic.h> + +DECLARE_GLOBAL_DATA_PTR; + +int board_init(void) +{ + gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL); +#ifdef CONFIG_EXYNOS_SPI + spi_init(); +#endif + return 0; +} + +int dram_init(void) +{ + gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE) + + get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE) + + get_ram_size((long *)PHYS_SDRAM_3, PHYS_SDRAM_3_SIZE) + + get_ram_size((long *)PHYS_SDRAM_4, PHYS_SDRAM_4_SIZE) + + get_ram_size((long *)PHYS_SDRAM_5, PHYS_SDRAM_7_SIZE) + + get_ram_size((long *)PHYS_SDRAM_6, PHYS_SDRAM_7_SIZE) + + get_ram_size((long *)PHYS_SDRAM_7, PHYS_SDRAM_7_SIZE) + + get_ram_size((long *)PHYS_SDRAM_8, PHYS_SDRAM_8_SIZE); + return 0; +} + +#if defined(CONFIG_POWER) +int power_init_board(void) +{ + if (pmic_init(I2C_PMIC)) + return -1; + else + return 0; +} +#endif + +void dram_init_banksize(void) +{ + gd->bd->bi_dram[0].start = PHYS_SDRAM_1; + gd->bd->bi_dram[0].size = get_ram_size((long *)PHYS_SDRAM_1, + PHYS_SDRAM_1_SIZE); + gd->bd->bi_dram[1].start = PHYS_SDRAM_2; + gd->bd->bi_dram[1].size = get_ram_size((long *)PHYS_SDRAM_2, + PHYS_SDRAM_2_SIZE); + gd->bd->bi_dram[2].start = PHYS_SDRAM_3; + gd->bd->bi_dram[2].size = get_ram_size((long *)PHYS_SDRAM_3, + PHYS_SDRAM_3_SIZE); + gd->bd->bi_dram[3].start = PHYS_SDRAM_4; + gd->bd->bi_dram[3].size = get_ram_size((long *)PHYS_SDRAM_4, + PHYS_SDRAM_4_SIZE); + gd->bd->bi_dram[4].start = PHYS_SDRAM_5; + gd->bd->bi_dram[4].size = get_ram_size((long *)PHYS_SDRAM_5, + PHYS_SDRAM_5_SIZE); + gd->bd->bi_dram[5].start = PHYS_SDRAM_6; + gd->bd->bi_dram[5].size = get_ram_size((long *)PHYS_SDRAM_6, + PHYS_SDRAM_6_SIZE); + gd->bd->bi_dram[6].start = PHYS_SDRAM_7; + gd->bd->bi_dram[6].size = get_ram_size((long *)PHYS_SDRAM_7, + PHYS_SDRAM_7_SIZE); + gd->bd->bi_dram[7].start = PHYS_SDRAM_8; + gd->bd->bi_dram[7].size = get_ram_size((long *)PHYS_SDRAM_8, + PHYS_SDRAM_8_SIZE); +} + +static int decode_sromc(const void *blob, struct fdt_sromc *config) +{ + int err; + int node; + + node = fdtdec_next_compatible(blob, 0, COMPAT_SAMSUNG_EXYNOS5_SROMC); + if (node < 0) { + debug("Could not find SROMC node\n"); + return node; + } + + config->bank = fdtdec_get_int(blob, node, "bank", 0); + config->width = fdtdec_get_int(blob, node, "width", 2); + + err = fdtdec_get_int_array(blob, node, "srom-timing", config->timing, + FDT_SROM_TIMING_COUNT); + if (err < 0) { + debug("Could not decode SROMC configuration\n"); + return -FDT_ERR_NOTFOUND; + } + + return 0; +} + +int board_eth_init(bd_t *bis) +{ +#ifdef CONFIG_SMC911X + u32 smc_bw_conf, smc_bc_conf; + struct fdt_sromc config; + fdt_addr_t base_addr; + int node; + + node = decode_sromc(gd->fdt_blob, &config); + if (node < 0) { + debug("%s: Could not find sromc configuration\n", __func__); + return 0; + } + node = fdtdec_next_compatible(gd->fdt_blob, node, COMPAT_SMSC_LAN9215); + if (node < 0) { + debug("%s: Could not find lan9215 configuration\n", __func__); + return 0; + } + + /* We now have a node, so any problems from now on are errors */ + base_addr = fdtdec_get_addr(gd->fdt_blob, node, "reg"); + if (base_addr == FDT_ADDR_T_NONE) { + debug("%s: Could not find lan9215 address\n", __func__); + return -1; + } + + /* Ethernet needs data bus width of 16 bits */ + if (config.width != 2) { + debug("%s: Unsupported bus width %d\n", __func__, + config.width); + return -1; + } + smc_bw_conf = SROMC_DATA16_WIDTH(config.bank) + | SROMC_BYTE_ENABLE(config.bank); + + smc_bc_conf = SROMC_BC_TACS(config.timing[FDT_SROM_TACS]) |\ + SROMC_BC_TCOS(config.timing[FDT_SROM_TCOS]) |\ + SROMC_BC_TACC(config.timing[FDT_SROM_TACC]) |\ + SROMC_BC_TCOH(config.timing[FDT_SROM_TCOH]) |\ + SROMC_BC_TAH(config.timing[FDT_SROM_TAH]) |\ + SROMC_BC_TACP(config.timing[FDT_SROM_TACP]) |\ + SROMC_BC_PMC(config.timing[FDT_SROM_PMC]); + + /* Select and configure the SROMC bank */ + exynos_pinmux_config(PERIPH_ID_SROMC, config.bank); + s5p_config_sromc(config.bank, smc_bw_conf, smc_bc_conf); + return smc911x_initialize(0, base_addr); +#endif + return 0; +} + +#ifdef CONFIG_DISPLAY_BOARDINFO +int checkboard(void) +{ + printf("\nBoard: SMDK5250\n"); + + return 0; +} +#endif + +#ifdef CONFIG_GENERIC_MMC +int board_mmc_init(bd_t *bis) +{ + int ret = 0; + + /* dwmmc initializattion for available channels */ + ret = exynos_dwmmc_init(gd->fdt_blob); + if (ret) + debug("dwmmc init failed\n"); + + return ret; +} +#endif + +static int board_uart_init(void) +{ + int err; + + err = exynos_pinmux_config(PERIPH_ID_UART0, PINMUX_FLAG_NONE); + if (err) { + debug("UART0 not configured\n"); + return err; + } + + err = exynos_pinmux_config(PERIPH_ID_UART1, PINMUX_FLAG_NONE); + if (err) { + debug("UART1 not configured\n"); + return err; + } + + err = exynos_pinmux_config(PERIPH_ID_UART2, PINMUX_FLAG_NONE); + if (err) { + debug("UART2 not configured\n"); + return err; + } + + err = exynos_pinmux_config(PERIPH_ID_UART3, PINMUX_FLAG_NONE); + if (err) { + debug("UART3 not configured\n"); + return err; + } + + return 0; +} + +#ifdef CONFIG_BOARD_EARLY_INIT_F +int board_early_init_f(void) +{ + int err; + err = board_uart_init(); + if (err) { + debug("UART init failed\n"); + return err; + } +#ifdef CONFIG_SYS_I2C_INIT_BOARD + board_i2c_init(gd->fdt_blob); +#endif + return err; +} +#endif diff --git a/board/samsung/smdk5250/smdk5250.c b/board/samsung/smdk5250/smdk5250.c index 73c3ec0..e0fec11 100644 --- a/board/samsung/smdk5250/smdk5250.c +++ b/board/samsung/smdk5250/smdk5250.c @@ -27,6 +27,7 @@ #include <netdev.h> #include <spi.h> #include <asm/arch/cpu.h> +#include <asm/arch/dwmmc.h> #include <asm/arch/gpio.h> #include <asm/arch/mmc.h> #include <asm/arch/pinmux.h> @@ -95,59 +96,13 @@ void dram_init_banksize(void) PHYS_SDRAM_8_SIZE); }
-#ifdef CONFIG_OF_CONTROL -static int decode_sromc(const void *blob, struct fdt_sromc *config) -{ - int err; - int node; - - node = fdtdec_next_compatible(blob, 0, COMPAT_SAMSUNG_EXYNOS5_SROMC); - if (node < 0) { - debug("Could not find SROMC node\n"); - return node; - } - - config->bank = fdtdec_get_int(blob, node, "bank", 0); - config->width = fdtdec_get_int(blob, node, "width", 2); - - err = fdtdec_get_int_array(blob, node, "srom-timing", config->timing, - FDT_SROM_TIMING_COUNT); - if (err < 0) { - debug("Could not decode SROMC configuration\n"); - return -FDT_ERR_NOTFOUND; - } - - return 0; -} -#endif - int board_eth_init(bd_t *bis) { #ifdef CONFIG_SMC911X u32 smc_bw_conf, smc_bc_conf; struct fdt_sromc config; fdt_addr_t base_addr; - int node; - -#ifdef CONFIG_OF_CONTROL - node = decode_sromc(gd->fdt_blob, &config); - if (node < 0) { - debug("%s: Could not find sromc configuration\n", __func__); - return 0; - } - node = fdtdec_next_compatible(gd->fdt_blob, node, COMPAT_SMSC_LAN9215); - if (node < 0) { - debug("%s: Could not find lan9215 configuration\n", __func__); - return 0; - }
- /* We now have a node, so any problems from now on are errors */ - base_addr = fdtdec_get_addr(gd->fdt_blob, node, "reg"); - if (base_addr == FDT_ADDR_T_NONE) { - debug("%s: Could not find lan9215 address\n", __func__); - return -1; - } -#else /* Non-FDT configuration - bank number and timing parameters*/ config.bank = CONFIG_ENV_SROM_BANK; config.width = 2; @@ -160,7 +115,6 @@ int board_eth_init(bd_t *bis) config.timing[FDT_SROM_TACP] = 0x09; config.timing[FDT_SROM_PMC] = 0x01; base_addr = CONFIG_SMC911X_BASE; -#endif
/* Ethernet needs data bus width of 16 bits */ if (config.width != 2) { @@ -199,16 +153,31 @@ int checkboard(void) #ifdef CONFIG_GENERIC_MMC int board_mmc_init(bd_t *bis) { - int err; + int err = 0, ret = 0;
err = exynos_pinmux_config(PERIPH_ID_SDMMC0, PINMUX_FLAG_8BIT_MODE); - if (err) { + if (err) debug("SDMMC0 not configured\n"); - return err; - } - - err = s5p_mmc_init(0, 8); - return err; + ret |= err; + + /*EMMC: dwmmc Channel-0 with 8 bit bus width */ + err = exynos_dwmmc_init(0, 8); + if (err) + debug("dwmmc Channel-0 init failed\n"); + ret |= err; + + err = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE); + if (err) + debug("SDMMC2 not configured\n"); + ret |= err; + + /*SD: dwmmc Channel-2 with 4 bit bus width */ + err = exynos_dwmmc_init(2, 4); + if (err) + debug("dwmmc Channel-2 init failed\n"); + ret |= err; + + return ret; } #endif
@@ -243,6 +212,24 @@ static int board_uart_init(void) return 0; }
+#ifdef CONFIG_SYS_I2C_INIT_BOARD +static int board_i2c_init(void) +{ + int i, err; + + for (i = 0; i < CONFIG_MAX_I2C_NUM; i++) { + err = exynos_pinmux_config((PERIPH_ID_I2C0 + i), + PINMUX_FLAG_NONE); + if (err) { + debug("I2C%d not configured\n", (PERIPH_ID_I2C0 + i)); + return err; + } + } + i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + return 0; +} +#endif + #ifdef CONFIG_BOARD_EARLY_INIT_F int board_early_init_f(void) { @@ -253,7 +240,7 @@ int board_early_init_f(void) return err; } #ifdef CONFIG_SYS_I2C_INIT_BOARD - board_i2c_init(gd->fdt_blob); + board_i2c_init(); #endif return err; } diff --git a/include/configs/exynos5250-dt.h b/include/configs/exynos5250-dt.h index 59182f4..6ce73dc 100644 --- a/include/configs/exynos5250-dt.h +++ b/include/configs/exynos5250-dt.h @@ -84,6 +84,8 @@ #define CONFIG_MMC #define CONFIG_SDHCI #define CONFIG_S5P_SDHCI +#define CONFIG_DWMMC +#define CONFIG_EXYNOS_DWMMC
#define CONFIG_BOARD_EARLY_INIT_F
diff --git a/include/i2c.h b/include/i2c.h index c60d075..0944141 100644 --- a/include/i2c.h +++ b/include/i2c.h @@ -263,6 +263,7 @@ extern int get_multi_sda_pin(void); extern int multi_i2c_init(void); #endif
+#ifdef CONFIG_OF_CONTROL /** * Get FDT values for i2c bus. * @@ -270,6 +271,7 @@ extern int multi_i2c_init(void); * @return the number of I2C bus */ void board_i2c_init(const void *blob); +#endif
/** * Find the I2C bus number by given a FDT I2C node.