On 26.04.21 13:08, Michal Simek wrote:
Enable EFI capsule update features to be enabled by default also with all dfu valid options for ZynqMP.
This feature was tested on Xilinx ZynqMP zcu104 board with defining dfu_alt_info="mmc 0:1=boot.bin fat 0 1;u-boot.itb fat 0 1" and dfu_alt_info="sf 0:0=boot.bin raw 0 0x50000;u-boot.itb raw 0x80000 0x500000".
There is a need to increase malloc size for getting dfu mmc to work.
Signed-off-by: Michal Simek michal.simek@xilinx.com CC: Sughosh Ganu sughosh.ganu@linaro.org CC: Ilias Apalodimas ilias.apalodimas@linaro.org CC: Heinrich Schuchardt xypron.glpk@gmx.de
I actually didn't try to boot out of qspi because qspi writing is likely broken and should be fixed. But I have checked that images are written to that previously erased locations.
There is a DFU driver for writing to RAM. You should be able to write to memory using capsule update and then do a CRC32 on the memory region for testing the correct result.
Best regards
Heinrich
U-Boot SPL 2021.04-00978-g76a8101e4548 (Apr 26 2021 - 13:01:46 +0200) PMUFW: v1.1 Loading new PMUFW cfg obj (2024 bytes) Silicon version: 3 EL Level: EL3 Chip ID: zu7e Multiboot: 0 Trying to boot from MMC2 spl: could not initialize mmc. error: -19 Trying to boot from MMC1 spl_load_image_fat_os: error reading image u-boot.bin, err - -2 NOTICE: ATF running on XCZU7EG/EV/silicon v4/RTL5.1 at 0xfffea000 NOTICE: BL31: v2.2(release):xilinx-v2020.2.2-k26 NOTICE: BL31: Built : 11:51:16, Apr 21 2021
U-Boot 2021.04-00978-g76a8101e4548 (Apr 26 2021 - 13:01:46 +0200)
Model: ZynqMP ZCU104 RevC Board: Xilinx ZynqMP DRAM: 2 GiB PMUFW: v1.1 EL Level: EL2 Chip ID: zu7e WDT: Started with servicing (60s timeout) NAND: 0 MiB MMC: mmc@ff170000: 0 Loading Environment from FAT... OK In: serial Out: serial Err: serial Net: ZYNQ GEM: ff0e0000, mdio bus ff0e0000, phyaddr 12, interface rgmii-id eth0: ethernet@ff0e0000 Scanning disk mmc@ff170000.blk... Found 4 disks ##Hit any key to stop autoboot: 0 ZynqMP> reset resetting ...
U-Boot SPL 2021.04-00978-g01e9f0ec63e4 (Apr 26 2021 - 13:04:48 +0200) PMUFW: v1.1 Loading new PMUFW cfg obj (2024 bytes) Silicon version: 3 EL Level: EL3 Chip ID: zu7e Multiboot: 0 Trying to boot from MMC2 spl: could not initialize mmc. error: -19 Trying to boot from MMC1 spl_load_image_fat_os: error reading image u-boot.bin, err - -2 NOTICE: ATF running on XCZU7EG/EV/silicon v4/RTL5.1 at 0xfffea000 NOTICE: BL31: v2.2(release):xilinx-v2020.2.2-k26 NOTICE: BL31: Built : 11:51:16, Apr 21 2021
U-Boot 2021.04-00978-g01e9f0ec63e4 (Apr 26 2021 - 13:04:48 +0200)
Model: ZynqMP ZCU104 RevC Board: Xilinx ZynqMP DRAM: 2 GiB PMUFW: v1.1 EL Level: EL2 Chip ID: zu7e WDT: Started with servicing (60s timeout) NAND: 0 MiB MMC: mmc@ff170000: 0 Loading Environment from FAT... OK In: serial Out: serial Err: serial Net: ZYNQ GEM: ff0e0000, mdio bus ff0e0000, phyaddr 12, interface rgmii-id eth0: ethernet@ff0e0000 Scanning disk mmc@ff170000.blk... Found 4 disks Hit any key to stop autoboot: 0 ZynqMP>
configs/xilinx_zynqmp_virt_defconfig | 9 +++++++++ include/configs/xilinx_zynqmp.h | 2 +- 2 files changed, 10 insertions(+), 1 deletion(-)
diff --git a/configs/xilinx_zynqmp_virt_defconfig b/configs/xilinx_zynqmp_virt_defconfig index 89c1dae2a1d9..9c496098584f 100644 --- a/configs/xilinx_zynqmp_virt_defconfig +++ b/configs/xilinx_zynqmp_virt_defconfig @@ -86,7 +86,11 @@ CONFIG_SATA_CEVA=y CONFIG_CLK_ZYNQMP=y CONFIG_DFU_TFTP=y CONFIG_DFU_TIMEOUT=y +CONFIG_DFU_MMC=y +CONFIG_DFU_NAND=y CONFIG_DFU_RAM=y +CONFIG_DFU_SF=y +CONFIG_DFU_MTD=y CONFIG_USB_FUNCTION_FASTBOOT=y CONFIG_FASTBOOT_FLASH=y CONFIG_FASTBOOT_FLASH_MMC_DEV=0 @@ -178,3 +182,8 @@ CONFIG_TPM=y CONFIG_SPL_GZIP=y # CONFIG_SPL_HEXDUMP is not set CONFIG_OF_LIBFDT_OVERLAY=y +CONFIG_EFI_RUNTIME_UPDATE_CAPSULE=y +CONFIG_EFI_CAPSULE_ON_DISK=y +CONFIG_EFI_CAPSULE_ON_DISK_EARLY=y +CONFIG_EFI_CAPSULE_FIRMWARE_FIT=y +CONFIG_EFI_CAPSULE_FIRMWARE_RAW=y diff --git a/include/configs/xilinx_zynqmp.h b/include/configs/xilinx_zynqmp.h index 36f3d962e417..986af2be7819 100644 --- a/include/configs/xilinx_zynqmp.h +++ b/include/configs/xilinx_zynqmp.h @@ -27,7 +27,7 @@ #endif
/* Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 0x2000000) +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 0x4000000)
/* Serial setup */ #define CONFIG_CPU_ARMV8