Re: [PATCH v5 1/3] arm: mvebu: dts: sync DTS

On 20.05.22 13:46, Robert Marko wrote:

Update the uDPU DTS to the version that is pending upstream [1][2][3][4].

[1] https://patchwork.kernel.org/project/linux-arm-kernel/patch/20220516124828.4... [2] https://patchwork.kernel.org/project/linux-arm-kernel/patch/20220516124828.4... [3] https://patchwork.kernel.org/project/linux-arm-kernel/patch/20220516124828.4... [4] https://patchwork.kernel.org/project/linux-arm-kernel/patch/20220516124828.4...

Signed-off-by: Robert Marko robert.marko@sartura.hr

Applied to u-boot-marvell/master

Thanks, Stefan

---

arch/arm/dts/armada-3720-uDPU.dts | 23 ++++++++++------------- 1 file changed, 10 insertions(+), 13 deletions(-)

diff --git a/arch/arm/dts/armada-3720-uDPU.dts b/arch/arm/dts/armada-3720-uDPU.dts index 1f534c0c65..f21a855fc6 100644 --- a/arch/arm/dts/armada-3720-uDPU.dts +++ b/arch/arm/dts/armada-3720-uDPU.dts @@ -16,7 +16,7 @@

/ { model = "Methode uDPU Board";

• compatible = "methode,udpu", "marvell,armada3720";

• compatible = "methode,udpu", "marvell,armada3720", "marvell,armada3710";

  chosen { stdout-path = "serial0:115200n8";

@@ -28,35 +28,34 @@ };

leds {

• pinctrl-names = "default";
  

  compatible = "gpio-leds";

• power1 {
  

• led-power1 {
  label = "udpu:green:power";
  gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
  

  };

• power2 {
  

• led-power2 {
  label = "udpu:red:power";
  gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
  

  };

• network1 {
  

• led-network1 {
  label = "udpu:green:network";
  gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
  

  };

• network2 {
  

• led-network2 {
  label = "udpu:red:network";
  gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
  

  };

• alarm1 {
  

• led-alarm1 {
  label = "udpu:green:alarm";
  gpios = <&gpionb 15 GPIO_ACTIVE_LOW>;
  

  };

• alarm2 {
  

• led-alarm2 {
  label = "udpu:red:alarm";
  gpios = <&gpionb 16 GPIO_ACTIVE_LOW>;
  

  };

@@ -99,7 +98,7 @@ pinctrl-names = "default"; pinctrl-0 = <&spi_quad_pins>;

• spi-flash@0 {

• flash@0 { compatible = "jedec,spi-nor"; reg = <0>; spi-max-frequency = <54000000>;

@@ -153,14 +152,12 @@ scl-gpios = <&gpionb 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; sda-gpios = <&gpionb 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;

• nct375@48 {

• status = "okay";
  

• temp-sensor@48 { compatible = "ti,tmp75c"; reg = <0x48>; };

• nct375@49 {

• status = "okay";
  

• temp-sensor@49 { compatible = "ti,tmp75c"; reg = <0x49>; };

Viele Grüße, Stefan Roese