Hi John,
I think it is better that you can add a new config, e.g. CONFIG_MIIGSK for MII gasket. Then if other i.MX platforms uses MIIGSK, we can use the config for it.
Thanks~~
Yours Terry
-----Original Message----- From: u-boot-bounces@lists.denx.de [mailto:u-boot-bounces@lists.denx.de] On Behalf Of John Rigby Sent: 2010年1月26日 14:13 To: u-boot@lists.denx.de Cc: John Rigby; Ben Warren Subject: [U-Boot] [PATCH V3 7/8] fec_mxc: add MX25 support
Use RMII for MX25 Add code to init gasket that enables RMII
Signed-off-by: John Rigby jcrigby@gmail.com CC: Ben Warren biggerbadderben@gmail.com --- drivers/net/fec_mxc.c | 31 ++++++++++++++++++++++++++++++- drivers/net/fec_mxc.h | 32 ++++++++++++++++++++++++++++++-- include/asm-arm/arch-mx25/clock.h | 1 + 3 files changed, 61 insertions(+), 3 deletions(-)
diff --git a/drivers/net/fec_mxc.c b/drivers/net/fec_mxc.c index b5619eb..f109485 100644 --- a/drivers/net/fec_mxc.c +++ b/drivers/net/fec_mxc.c @@ -347,6 +347,34 @@ static int fec_open(struct eth_device *edev) */ writel(readl(&fec->eth->ecntrl) | FEC_ECNTRL_ETHER_EN, &fec->eth->ecntrl); +#ifdef CONFIG_MX25 + udelay(100); + /* + * setup the MII gasket for RMII mode + */ + + /* disable the gasket */ + writew(0, &fec->eth->miigsk_enr); + + /* wait for the gasket to be disabled */ + while (readw(&fec->eth->miigsk_enr) & MIIGSK_ENR_READY) + udelay(2); + + /* configure gasket for RMII, 50 MHz, no loopback, and no echo */ + writew(MIIGSK_CFGR_IF_MODE_RMII, &fec->eth->miigsk_cfgr); + + /* re-enable the gasket */ + writew(MIIGSK_ENR_EN, &fec->eth->miigsk_enr); + + /* wait until MII gasket is ready */ + int max_loops = 10; + while ((readw(&fec->eth->miigsk_enr) & MIIGSK_ENR_READY) == 0) { + if (--max_loops <= 0) { + printf("WAIT for MII Gasket ready timed out\n"); + break; + } + } +#endif
miiphy_wait_aneg(edev); miiphy_speed(edev->name, CONFIG_FEC_MXC_PHYADDR); @@ -498,7 +526,8 @@ static void fec_halt(struct eth_device *dev) * Disable the Ethernet Controller * Note: this will also reset the BD index counter! */ - writel(readl(&fec->eth->ecntrl) & ~FEC_ECNTRL_ETHER_EN, &fec->eth->ecntrl); + writel(readl(&fec->eth->ecntrl) & ~FEC_ECNTRL_ETHER_EN, + &fec->eth->ecntrl); fec->rbd_index = 0; fec->tbd_index = 0; debug("eth_halt: done\n"); diff --git a/drivers/net/fec_mxc.h b/drivers/net/fec_mxc.h index 6cb1bfc..5d0d69d 100644 --- a/drivers/net/fec_mxc.h +++ b/drivers/net/fec_mxc.h @@ -145,9 +145,17 @@ struct ethernet_regs { uint32_t r_fdxfc; /* MBAR_ETH + 0x2DC */ uint32_t ieee_r_octets_ok; /* MBAR_ETH + 0x2E0 */
- uint32_t res14[6]; /* MBAR_ETH + 0x2E4-2FC */ - + uint32_t res14[7]; /* MBAR_ETH + 0x2E4-2FC */ + +#ifdef CONFIG_MX25 + uint16_t miigsk_cfgr; /* MBAR_ETH + 0x300 */ + uint16_t res15[3]; /* MBAR_ETH + 0x302-306 */ + uint16_t miigsk_enr; /* MBAR_ETH + 0x308 */ + uint16_t res16[3]; /* MBAR_ETH + 0x30a-30e */ + uint32_t res17[60]; /* MBAR_ETH + 0x300-3FF */ +#else uint32_t res15[64]; /* MBAR_ETH + 0x300-3FF */ +#endif };
#define FEC_IEVENT_HBERR 0x80000000 @@ -196,6 +204,26 @@ struct ethernet_regs { #define FEC_ECNTRL_RESET 0x00000001 /* reset the FEC */ #define FEC_ECNTRL_ETHER_EN 0x00000002 /* enable the FEC */
+#ifdef CONFIG_MX25 +/* defines for MIIGSK */ +/* RMII frequency control: 0=50MHz, 1=5MHz */ +#define MIIGSK_CFGR_FRCONT (1 << 6) +/* loopback mode */ +#define MIIGSK_CFGR_LBMODE (1 << 4) +/* echo mode */ +#define MIIGSK_CFGR_EMODE (1 << 3) +/* MII gasket mode field */ +#define MIIGSK_CFGR_IF_MODE_MASK (3 << 0) +/* MMI/7-Wire mode */ +#define MIIGSK_CFGR_IF_MODE_MII (0 << 0) +/* RMII mode */ +#define MIIGSK_CFGR_IF_MODE_RMII (1 << 0) +/* reflects MIIGSK Enable bit (RO) */ +#define MIIGSK_ENR_READY (1 << 2) +/* enable MIGSK (set by default) */ +#define MIIGSK_ENR_EN (1 << 1) +#endif + /** * @brief Descriptor buffer alignment * diff --git a/include/asm-arm/arch-mx25/clock.h b/include/asm-arm/arch-mx25/clock.h index b0752e7..c59f588 100644 --- a/include/asm-arm/arch-mx25/clock.h +++ b/include/asm-arm/arch-mx25/clock.h @@ -30,6 +30,7 @@ ulong imx_get_perclk(int clk); ulong imx_get_ahbclk(void);
#define imx_get_uartclk() imx_get_perclk(15) +#define imx_get_fecclk() (imx_get_ahbclk()/2)
#endif /* __ASM_ARCH_CLOCK_H */ -- 1.6.4.2.236.gf324c
_______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot