This is not needed anymore. Drop it.
Signed-off-by: Simon Glass sjg@chromium.org ---
Changes in v2: - Enable LED on the 5 affected platforms - Reorder patches for bisectability
include/status_led.h | 104 ------------------------------------------- 1 file changed, 104 deletions(-) delete mode 100644 include/status_led.h
diff --git a/include/status_led.h b/include/status_led.h deleted file mode 100644 index 59cf9f89956..00000000000 --- a/include/status_led.h +++ /dev/null @@ -1,104 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2000-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - */ - -/* - * The purpose of this code is to signal the operational status of a - * target which usually boots over the network; while running in - * PCBoot, a status LED is blinking. As soon as a valid BOOTP reply - * message has been received, the LED is turned off. The Linux - * kernel, once it is running, will start blinking the LED again, - * with another frequency. - */ - -#ifndef _STATUS_LED_H_ -#define _STATUS_LED_H_ - -#ifdef CONFIG_LED_STATUS - -#define LED_STATUS_PERIOD (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ) -#ifdef CONFIG_LED_STATUS1 -#define LED_STATUS_PERIOD1 (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ1) -#endif /* CONFIG_LED_STATUS1 */ -#ifdef CONFIG_LED_STATUS2 -#define LED_STATUS_PERIOD2 (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ2) -#endif /* CONFIG_LED_STATUS2 */ -#ifdef CONFIG_LED_STATUS3 -#define LED_STATUS_PERIOD3 (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ3) -#endif /* CONFIG_LED_STATUS3 */ -#ifdef CONFIG_LED_STATUS4 -#define LED_STATUS_PERIOD4 (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ4) -#endif /* CONFIG_LED_STATUS4 */ -#ifdef CONFIG_LED_STATUS5 -#define LED_STATUS_PERIOD5 (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ5) -#endif /* CONFIG_LED_STATUS5 */ - -void status_led_init(void); -void status_led_tick(unsigned long timestamp); -void status_led_set(int led, int state); - -static inline void status_led_boot_blink(void) -{ -#ifdef CONFIG_LED_STATUS_BOOT_ENABLE - status_led_set(CONFIG_LED_STATUS_BOOT, CONFIG_LED_STATUS_BLINKING); -#endif -} - -/***** MVS v1 **********************************************************/ -#if (defined(CONFIG_MVS) && CONFIG_MVS < 2) -# define STATUS_LED_PAR im_ioport.iop_pdpar -# define STATUS_LED_DIR im_ioport.iop_pddir -# undef STATUS_LED_ODR -# define STATUS_LED_DAT im_ioport.iop_pddat - -# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ - -/***** Someone else defines these *************************************/ -#elif defined(STATUS_LED_PAR) - /* - * ADVICE: Define in your board configuration file rather than - * filling this file up with lots of custom board stuff. - */ -#else -# error Status LED configuration missing -#endif -/************************************************************************/ - -#include <asm/status_led.h> - -#else - -static inline void status_led_init(void) { } -static inline void status_led_set(int led, int state) { } -static inline void status_led_boot_blink(void) { } - -#endif /* CONFIG_LED_STATUS */ - -/* - * Coloured LEDs API - */ -#ifndef __ASSEMBLY__ -void coloured_LED_init(void); -void red_led_on(void); -void red_led_off(void); -void green_led_on(void); -void green_led_off(void); -void yellow_led_on(void); -void yellow_led_off(void); -void blue_led_on(void); -void blue_led_off(void); -#else - .extern LED_init - .extern red_led_on - .extern red_led_off - .extern yellow_led_on - .extern yellow_led_off - .extern green_led_on - .extern green_led_off - .extern blue_led_on - .extern blue_led_off -#endif - -#endif /* _STATUS_LED_H_ */