On Sat, 4 Mar 2023 at 11:20, Pali Rohár pali@kernel.org wrote:
On Saturday 04 March 2023 11:50:34 Pali Rohár wrote:
Disassembling A385 BootROM binary reveal how BootROM interprets strapping pins for Boot Device Mode. All possible options are:
0x00..0x07 -> Parallel NOR 0x08..0x15 -> Parallel NAND 0x16..0x17 -> Parallel NOR 0x18..0x25 -> Parallel NAND 0x26..0x27 -> SPI NAND 0x28..0x29 -> UART xmodem 0x2a..0x2b -> SATA 0x2c..0x2d -> PCI Express 0x2e..0x2f -> Parallel NOR 0x30..0x31 -> SD / eMMC 0x32..0x39 -> SPI NOR 0x3a..0x3c -> Parallel NOR 0x3d..0x3e -> UART debug console 0x3f -> Invalid
Clearfog has 5-bit DIP switch and seems that it is directly mapped to the Boot Device mode with most significant bit of boot mode pulled to high (sixth bit not present on the switch) and flipped second, third and fifth bits of the boot mode.
Based on documentation Clearfog DIP switch should be set to 11100 for SATA booting, by flipping bits it is 01010, by adding MSB it is 101010, which is hex 0x2a --> matches A385 SATA boot mode.
The Clearfog schematics indicate the switch is internally pulled to 0x36 / 110110. 110110 XOR 11100 = 101010 = 0x2a. The math checks out and corresponds to the documented modes as well as the enumeration I did a few years ago: 00000 nothing [0x36] 00001 nothing [0x37] 00010 SPI [0x34] (documented SPI) 00011 SPI [0x35] 00100 SPI [0x32] 00101 SPI [0x33] 00110 MMC (Card did not respond to voltage select!) [0x30] 00111 MMC [0x31] (documented SD/eMMC) 01000 nothing [0x3e] 01001 UART [0x3f] (documented UART) 01010 NOR [0x3c] 01011 nothing [0x3d] 01100 NOR [0x3a] 01101 NOR [0x3b] 01110 nothing [0x38] 01111 nothing [0x39] 10000 nothing [0x26] 10001 nothing [0x27] 10010 NAND [0x24] 10011 NAND [0x25] 10100 NAND [0x22] 10101 NAND [0x23] 10110 NAND [0x20] 10111 NAND [0x21] 11000 NOR [0x2e] 11001 nothing [0x2f] 11010 PEX0 (00) [0x2c] 11011 PEX0 (1A) [0x2d] 11100 nothing [0x2a] (I don't think I had a SATA card attached, but this is documented SATA) 11101 nothing [0x2b] 11110 nothing [0x28] 11111 nothing [0x29] Where "nothing" indicates no BootROM output
Can somebody check if UART debug console boot mode works on Clearfog? It is boot mode when BootROM enters into simple debug console with few commands. Via kwboot it is possible to enter into this mode (it sends magic sequence) but from this information it looks like that it should be possible also without magic sequence, just by configuring boot mode.
I didn't know about this before. I tried with the magic sequence and it works (though it needs the A38x output workaround mentioned here [1]. The boot mode is the one set by 0x3d / 111101 or 0x3e / 111110, right? 0x3d: 111101 XOR 110110 = 01011 0x3e: 111110 XOR 110110 = 01000 Neither of those gives an interactive serial console, and even if the output workaround is entered there is never anything that appears in the console. It doesn't even echo the data I type in.
[1] https://manpages.debian.org/testing/u-boot-tools/kwboot.1.en.html
Note that Boot Device Mode Options in A38x Hardware Specifications is incomplete.
Signed-off-by: Pali Rohár pali@kernel.org
arch/arm/mach-mvebu/include/mach/soc.h | 11 +++++++---- 1 file changed, 7 insertions(+), 4 deletions(-)
diff --git a/arch/arm/mach-mvebu/include/mach/soc.h
b/arch/arm/mach-mvebu/include/mach/soc.h
index aa42db36a1ee..698b70339436 100644 --- a/arch/arm/mach-mvebu/include/mach/soc.h +++ b/arch/arm/mach-mvebu/include/mach/soc.h @@ -160,11 +160,14 @@ #define BOOT_DEV_SEL_OFFS 4 #define BOOT_DEV_SEL_MASK (0x3f << BOOT_DEV_SEL_OFFS)
-#define BOOT_FROM_NAND(x) (x == 0x0A) -#define BOOT_FROM_SATA(x) (x == 0x2A) -#define BOOT_FROM_UART(x) (x == 0x28) -#define BOOT_FROM_SPI(x) (x == 0x32) +#define BOOT_FROM_NOR(x) ((x >= 0x00 && x <= 0x07) || x == 0x16 ||
x == 0x17 || x == 0x2E || x == 0x2F || (x >= 0x3A && x <= 0x3C))
+#define BOOT_FROM_NAND(x) ((x >= 0x08 && x <= 0x15) || (x >= 0x18 &&
x <= 0x25))
+#define BOOT_FROM_SPINAND(x) (x == 0x26 || x == 0x27) +#define BOOT_FROM_UART(x) (x == 0x28 || x == 0x29) +#define BOOT_FROM_SATA(x) (x == 0x2A || x == 0x2B) +#define BOOT_FROM_PEX(x) (x == 0x2C || x == 0x2D) #define BOOT_FROM_MMC(x) (x == 0x30 || x == 0x31) +#define BOOT_FROM_SPI(x) (x >= 0x32 && x <= 0x39)
#define CONFIG_SYS_TCLK ((readl(CONFIG_SAR_REG) & BIT(15))
? \
200000000 : 250000000)-- 2.20.1