cgtqmx6eval has a PFUZE100 FSL PMIC connected to I2C2.
Add support for it.
Signed-off-by: Otavio Salvador otavio@ossystems.com.br ---
board/congatec/cgtqmx6eval/cgtqmx6eval.c | 83 ++++++++++++++++++++++++++++++++ include/configs/cgtqmx6eval.h | 13 +++++ 2 files changed, 96 insertions(+)
diff --git a/board/congatec/cgtqmx6eval/cgtqmx6eval.c b/board/congatec/cgtqmx6eval/cgtqmx6eval.c index 0a8eccd..9167cf8 100644 --- a/board/congatec/cgtqmx6eval/cgtqmx6eval.c +++ b/board/congatec/cgtqmx6eval/cgtqmx6eval.c @@ -16,11 +16,15 @@ #include <asm/gpio.h> #include <asm/imx-common/iomux-v3.h> #include <asm/imx-common/boot_mode.h> +#include <asm/imx-common/mxc_i2c.h> #include <malloc.h> #include <mmc.h> #include <fsl_esdhc.h> #include <miiphy.h> #include <netdev.h> +#include <i2c.h> +#include <power/pmic.h> +#include <power/pfuze100_pmic.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -38,6 +42,13 @@ DECLARE_GLOBAL_DATA_PTR; PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ + PAD_CTL_ODE | PAD_CTL_SRE_FAST) + +#define MX6Q_QMX6_PFUZE_MUX IMX_GPIO_NR(6, 9) + int dram_init(void) { gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE); @@ -140,6 +151,76 @@ static iomux_v3_cfg_t enet_pads_ar8035[] = { MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), };
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL) +struct i2c_pads_info i2c_pad_info1 = { + .scl = { + .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | PC, + .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | PC, + .gp = IMX_GPIO_NR(4, 12) + }, + .sda = { + .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | PC, + .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | PC, + .gp = IMX_GPIO_NR(4, 13) + } +}; + +#define I2C_PMIC 1 /* I2C2 port is used to connect to the PMIC */ + +struct interface_level { + char *name; + uchar value; +}; + +static struct interface_level mipi_levels[] = { + {"0V0", 0x00}, + {"2V5", 0x17}, +}; + +/* setup board specific PMIC */ +int power_init_board(void) +{ + struct pmic *p; + u32 id1, id2, i; + int ret; + char const *lv_mipi; + + /* configure I2C multiplexer */ + gpio_direction_output(MX6Q_QMX6_PFUZE_MUX, 1); + + power_pfuze100_init(I2C_PMIC); + p = pmic_get("PFUZE100"); + if (!p) + return -EINVAL; + + ret = pmic_probe(p); + if (ret) + return ret; + + pmic_reg_read(p, PFUZE100_DEVICEID, &id1); + pmic_reg_read(p, PFUZE100_REVID, &id2); + printf("PFUZE100 Rev. [%02x/%02x] detected\n", id1, id2); + + if (id2 >= 0x20) { + /* set level of MIPI if specified */ + lv_mipi = getenv("lv_mipi"); + if (lv_mipi) { + for (i = 0; i < ARRAY_SIZE(mipi_levels); i++) { + if (!strcmp(mipi_levels[i].name, lv_mipi)) { + printf("set MIPI level %s\n", + mipi_levels[i].name); + ret = pmic_reg_write(p, PFUZE100_VGEN4VOL, + mipi_levels[i].value); + if (ret) + return ret; + } + } + } + } + + return 0; +} + int board_eth_init(bd_t *bis) { struct phy_device *phydev; @@ -390,6 +471,8 @@ int board_init(void) /* address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+ setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); + return 0; }
diff --git a/include/configs/cgtqmx6eval.h b/include/configs/cgtqmx6eval.h index 146fa5e..4c91154 100644 --- a/include/configs/cgtqmx6eval.h +++ b/include/configs/cgtqmx6eval.h @@ -65,6 +65,19 @@ #define CONFIG_MXC_OCOTP #endif
+/* I2C Configs */ +#define CONFIG_CMD_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_MXC +#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ +#define CONFIG_SYS_I2C_SPEED 100000 + +/* PMIC */ +#define CONFIG_POWER +#define CONFIG_POWER_I2C +#define CONFIG_POWER_PFUZE100 +#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08 + #define CONFIG_DEFAULT_FDT_FILE "imx6q-congatec.dtb"
#define CONFIG_EXTRA_ENV_SETTINGS \