The Tanix TX1 is a tiny TV box, featuring the Allwinner H313 SoC with up to 2GB of DRAM and 16GB of eMMC. There is no SD card or Ethernet port on this small device, but it can be booted via the USB debug "FEL" mode. The bootloader could then be written to the eMMC.
Add the defconfig for that board, and add the devicetree file to the Makefile, for it to be built. The DRAM parameters were taken from the vendor firmware on the eMMC.
Signed-off-by: Andre Przywara andre.przywara@arm.com --- arch/arm/dts/Makefile | 1 + configs/tanix_tx1_defconfig | 25 +++++++++++++++++++++++++ 2 files changed, 26 insertions(+) create mode 100644 configs/tanix_tx1_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 127345975ef..69b0d6a9ad7 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -779,6 +779,7 @@ dtb-$(CONFIG_MACH_SUN50I_H6) += \ sun50i-h6-tanix-tx6.dtb \ sun50i-h6-tanix-tx6-mini.dtb dtb-$(CONFIG_MACH_SUN50I_H616) += \ + sun50i-h313-tanix-tx1.dtb \ sun50i-h616-orangepi-zero2.dtb \ sun50i-h618-orangepi-zero2w.dtb \ sun50i-h618-orangepi-zero3.dtb \ diff --git a/configs/tanix_tx1_defconfig b/configs/tanix_tx1_defconfig new file mode 100644 index 00000000000..9915fff4a00 --- /dev/null +++ b/configs/tanix_tx1_defconfig @@ -0,0 +1,25 @@ +CONFIG_ARM=y +CONFIG_ARCH_SUNXI=y +CONFIG_DEFAULT_DEVICE_TREE="sun50i-h313-tanix-tx1" +CONFIG_SPL=y +CONFIG_DRAM_SUN50I_H616_DX_ODT=0x06060606 +CONFIG_DRAM_SUN50I_H616_DX_DRI=0x0d0d0d0d +CONFIG_DRAM_SUN50I_H616_CA_DRI=0x1919 +CONFIG_DRAM_SUN50I_H616_ODT_EN=0x9988eeee +CONFIG_DRAM_SUN50I_H616_TPR6=0x2fb08080 +CONFIG_DRAM_SUN50I_H616_TPR10=0x402f4469 +CONFIG_DRAM_SUN50I_H616_TPR11=0x0e0f0d0d +CONFIG_DRAM_SUN50I_H616_TPR12=0x11131213 +CONFIG_MACH_SUN50I_H616=y +CONFIG_SUNXI_DRAM_H616_LPDDR3=y +CONFIG_R_I2C_ENABLE=y +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +CONFIG_SPL_I2C=y +CONFIG_SPL_SYS_I2C_LEGACY=y +CONFIG_SYS_I2C_MVTWSI=y +CONFIG_SYS_I2C_SLAVE=0x7f +CONFIG_SYS_I2C_SPEED=400000 +CONFIG_AXP313_POWER=y +CONFIG_AXP_DCDC3_VOLT=1200 +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_OHCI_HCD=y