From: Jagan Teki jagan@openedev.com
Enable DM_USB and removed non-DM_USB related config options.
Signed-off-by: Jagan Teki jagan@amarulasolutions.com Reviewed-by: Fabio Estevam fabio.estevam@nxp.com --- arch/arm/cpu/armv7/mx6/Kconfig | 1 + board/freescale/mx6sabresd/mx6sabresd.c | 65 --------------------------------- include/configs/mx6sabresd.h | 11 ++---- 3 files changed, 5 insertions(+), 72 deletions(-)
diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig index f203cf6..d1ba801 100644 --- a/arch/arm/cpu/armv7/mx6/Kconfig +++ b/arch/arm/cpu/armv7/mx6/Kconfig @@ -218,6 +218,7 @@ config TARGET_MX6SABRESD select DM_MMC select DM_REGULATOR select DM_THERMAL + select DM_USB select PINCTRL select PINCTRL_IMX6 select SUPPORT_SPL diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c index 7af263d..688b326 100644 --- a/board/freescale/mx6sabresd/mx6sabresd.c +++ b/board/freescale/mx6sabresd/mx6sabresd.c @@ -26,7 +26,6 @@ #include <power/pmic.h> #include <power/pfuze100_pmic.h> #include "../common/pfuze.h" -#include <usb.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -392,67 +391,6 @@ int board_eth_init(bd_t *bis) return cpu_eth_init(bis); }
-#ifdef CONFIG_USB_EHCI_MX6 -#define USB_OTHERREGS_OFFSET 0x800 -#define UCTRL_PWR_POL (1 << 9) - -static iomux_v3_cfg_t const usb_otg_pads[] = { - IOMUX_PADS(PAD_EIM_D22__USB_OTG_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)), - IOMUX_PADS(PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL)), -}; - -static iomux_v3_cfg_t const usb_hc1_pads[] = { - IOMUX_PADS(PAD_ENET_TXD1__GPIO1_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL)), -}; - -static void setup_usb(void) -{ - SETUP_IOMUX_PADS(usb_otg_pads); - - /* - * set daisy chain for otg_pin_id on 6q. - * for 6dl, this bit is reserved - */ - imx_iomux_set_gpr_register(1, 13, 1, 0); - - SETUP_IOMUX_PADS(usb_hc1_pads); -} - -int board_ehci_hcd_init(int port) -{ - u32 *usbnc_usb_ctrl; - - if (port > 1) - return -EINVAL; - - usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET + - port * 4); - - setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL); - - return 0; -} - -int board_ehci_power(int port, int on) -{ - switch (port) { - case 0: - break; - case 1: - if (on) - gpio_direction_output(IMX_GPIO_NR(1, 29), 1); - else - gpio_direction_output(IMX_GPIO_NR(1, 29), 0); - break; - default: - printf("MXC USB port %d not yet supported\n", port); - return -EINVAL; - } - - return 0; -} -#endif - int board_early_init_f(void) { setup_iomux_uart(); @@ -475,9 +413,6 @@ int board_init(void) setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c_pad_info1); else setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info1); -#ifdef CONFIG_USB_EHCI_MX6 - setup_usb(); -#endif
return 0; } diff --git a/include/configs/mx6sabresd.h b/include/configs/mx6sabresd.h index b90afe0..44c7cf6 100644 --- a/include/configs/mx6sabresd.h +++ b/include/configs/mx6sabresd.h @@ -66,13 +66,10 @@ #define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
/* USB Configs */ -#ifdef CONFIG_CMD_USB -#define CONFIG_EHCI_HCD_INIT_AFTER_RESET -#define CONFIG_USB_HOST_ETHER -#define CONFIG_USB_ETHER_ASIX -#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) -#define CONFIG_MXC_USB_FLAGS 0 -#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 /* Enabled USB controller number */ +#ifdef CONFIG_USB_EHCI_MX6 +# define CONFIG_USB_HOST_ETHER +# define CONFIG_USB_ETHER_ASIX +# define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) #endif
#endif /* __MX6QSABRESD_CONFIG_H */