Dear Wolfgang and Jean-Christophe,
Jean-Christophe PLAGNIOL-VILLARD wrote:
On 01:00 Sun 22 Feb , Wolfgang Denk wrote:
Dear Jean-Christophe,
I have the following patches still marked as open in my list. Could you please have a look...
ARM, AT91:
04/24 michael [U-Boot-Users] [PATCH ARM 0/2] Ide support 04/24 michael [U-Boot-Users] [PATCH ARM 1/2] Ide support io function 04/24 michael [U-Boot-Users] [PATCH ARM 2/2] Ide support. Ide registration 08/15 Sergey Lapin [U-Boot] [PATCH][Re-submit] Hardware watchdog support for AT91SAM9260 CPU
at91 watchdog support already mainline
08/28 Markus Kammerstet [U-Boot] PATCH: U-Boot support for Olimex SAM9L-9260 development board 10/07 "Alan Carvalho de [U-Boot] [PATCH 2/3] iMX31: Add support to copy NAND Flash code to RAM 10/07 "Alan Carvalho de [U-Boot] [PATCH 3/3] iMX31: Add support to iMX31PDK board boots from NAND Flash 10/13 "Roman Mashak" [U-Boot] [PATCH] ARM926EJ-S: relocate OMAP specific 'cpuinfo.c' into OMAP directory
applied
10/21 Tomohiro Masubuch [U-Boot] [PATCH v4] Add support for KMC KZM-ARM11-01 board 10/23 Magnus Lilja [U-Boot] [PATCH 1/2] i.MX31: Use do_div for some calculations. 10/23 Magnus Lilja [U-Boot] [PATCH 2/2] i.MX31: Add basic support for Freescale's i.MX31 PDK board. 11/07 Ilko Iliev [U-Boot] [PATCH] at91: add support for PM9261 board
need fix
11/13 Chaofu Chen [U-Boot] [PATCH] bug fix for the delay function of ARM s3c44b0 11/21 Hugo Villeneuve [U-Boot] [PATCH 1/1] ARM DaVinci: Add common peripherals and modules enable functions. 11/26 Jens Scharsig [U-Boot] [PATCH] AT91RM9200 BGA port D defines 12/04 Stefan Althoefer [U-Boot] [PATCH] ARM: add IDE init to lib_arm/board.c Part 1/1 12/11 Rohit Hagargundgi [U-Boot] [PATCH v2 2/4] Environment support for Flex-OneNAND 12/11 Rohit Hagargundgi [U-Boot] [PATCH v2 3/4] JFFS2 commands support for Flex-OneNAND 12/11 Rohit Hagargundgi [U-Boot] [PATCH v2 4/4] Flex-OneNAND boundary setting command 12/11 Rohit Hagargundgi [U-Boot] [PATCH 0/3] Bad blocks and Partition support for OneNAND / Flex-OneNAND 12/11 Rohit Hagargundgi [U-Boot] [PATCH 1/3] Bad block support for environment variables partition in OneNAND 12/11 Rohit Hagargundgi [U-Boot] [PATCH 2/3] Add partition based OneNAND commands 12/11 Rohit Hagargundgi [U-Boot] [PATCH 3/3] Create bad block aware partition table 12/13 Jean-Christophe P [U-Boot] [PATCH] integratorap: fix PCI support 12/14 Dirk Behme [U-Boot] [PATCH 01/15 v6] OMAP3: Add pin mux, clock and cpu headers
omap3 first series already mainline
Yes. Agreeed. All xx/15 OMAP3 patches are applied. You can remove them from this list.
12/14 Dirk Behme [U-Boot] [PATCH 05/15 v6] : Add common board, interrupt and system info
Already applied as stated above. Can be removed from this list.
12/17 Peter Tyser [U-Boot] [PATCH v6 0/3] Support for XPedite5370 and misc GPIO 01/07 Ulf Samuelsson [U-Boot] [PATCH 1/1] ARM: Add command to control coloured led from the console 01/20 Ben Warren Re: [U-Boot] [PATCH] Add support W90P710 ARM SoC from Nuvoton 01/22 Jean-Christophe P [U-Boot] [PATCH] at91rm9200: move serial driver to drivers/serial 01/22 Jean-Christophe P [U-Boot] [PATCH 0/2] at91sam9: add watchdog support 01/22 Jean-Christophe P [U-Boot] [PATCH 2/2] at91sam9263ek: active watchdog support via at91sam9263ek_wdt_config 01/22 Jean-Christophe P [U-Boot] [PATCH 1/2] at91sam9: add watchdog support 01/24 Michael Roth [U-Boot] Patches for new at91 board / lowlevel_init.S
NACK
01/25 Michael Roth Re: [U-Boot] Patches for new at91 board / lowlevel_init.S
NACK
01/25 Jason Kridner [U-Boot] [PATCH v2 0/5] OMAP3: Add OMAP3 board support 01/25 Jason Kridner [U-Boot] [PATCH v2 1/5] OMAP3: Add common power code, README, and BeagleBoard 01/25 Jason Kridner [U-Boot] [PATCH v2 2/5] OMAP3: Add Overo board 01/25 Jason Kridner [U-Boot] [PATCH v2 3/5] OMAP3: Add EVM board 01/25 Jason Kridner [U-Boot] [PATCH v2 4/5] OMAP3: Add Pandora support 01/25 Jason Kridner [U-Boot] [PATCH v2 5/5] OMAP3: Add Zoom1 board support
These 6 OMAP3 patches are already applied, too. Can be removed from this list.
01/26 Magnus Lilja Re: [U-Boot] [PATCH v3 0/6] i.MX31: Add NAND support and new PDK board. 01/27 Dirk Behme [U-Boot] [PATCH v3 1/5] OMAP3: Add common power code, README, and BeagleBoard
Already applied, too. Can be removed from this list.
02/01 Jean-Christophe P [U-Boot] [PATCH] at91sam9xeek: fix soc name 02/01 Jean-Christophe P [U-Boot] [PATCH 2/2] at91sam9263ek: active watchdog support via at91sam9263ek_wdt_config 02/01 Jean-Christophe P [U-Boot] [PATCH 1/2] at91sam9: add watchdog support 02/02 Dirk Behme [U-Boot] [PATCH 3/7] OMAP3: Add OMAP3 auto detection 02/02 Dirk Behme [U-Boot] [PATCH 6/7] OMAP3: Add OMAP3 core changes for MUSB 02/02 Dirk Behme [U-Boot] [PATCH 7/7] OMAP3: Clean up MMC code
These 3 OMAP3 patches are replaced by v2 below. Can be removed from this list.
02/03 Jean-Christophe P [U-Boot] [PATCH] integratorap: fix PCI support 02/05 Grazvydas Ignotas Re: [U-Boot] [PATCH 4/7] OMAP3: Pandora: Update pin mux
Replaced by v2 below. Can be removed from this list.
02/06 Michael Roth [U-Boot] [PATCH] at91: CONFIG_USART3 renamed to CONFIG_USART_DBGU 02/06 Michael Roth [U-Boot] [PATCH] at91: Factored out common serial hardware initialization 02/06 Jean-Christophe P Re: [U-Boot] [PATCH] at91: Factored out common serial hardware initialization 02/06 Mark Jackson Re: [U-Boot] [PATCH 1/1] Setup extra MIMC200 chip selects 02/06 Jean-Christophe P Re: [U-Boot] [PATCH] Add support W90P710 ARM SoC from Nuvoton 02/07 Anatolij Gustschi [U-Boot] [PATCH 1/9 v4] i.MX31: fix SPI driver for shorter than 32 bit
go throught video tree with the video patsh set
02/07 Jean-Christophe P Re: [U-Boot] [PATCH 1/9 v4] i.MX31: fix SPI driver for shorter than 32 bit 02/07 Anatolij Gustschi Re: [U-Boot] [PATCH 1/9 v4] i.MX31: fix SPI driver for shorter than 32 bit 02/07 Anatolij Gustschi [U-Boot] [PATCH 2/9 v4] i.MX31: add a simple gpio driver 02/09 Alessandro Rubini [U-Boot] [PATCH 1/3] Added nomadik.h header 02/10 Fabio Porcedda [U-Boot] Atmel AT91 USB Device Controller Driver 02/10 Remy Bohmer Re: [U-Boot] Atmel AT91 USB Device Controller Driver 02/11 Remy Bohmer Re: [U-Boot] Atmel AT91 USB Device Controller Driver 02/12 Dirk Behme [U-Boot] [PATCH 0/7 v2] OMAP3: Add some additional improvements and fixes
Yes. Still pending. See my summary of what is still pending below, too. Will hopefully be easier ;)
02/12 Dirk Behme Re: [U-Boot] [PATCH 6/7] OMAP3: Add OMAP3 core changes for MUSB
Hmm, I don't think this is a patch, just a mail discussing the patch. Please remove from this list.
02/12 Dirk Behme [U-Boot] [PATCH 4/7 v2] OMAP3: Pandora: Update pin mux 02/12 Dirk Behme [U-Boot] [PATCH 3/7 v2] OMAP3: Add OMAP3 auto detection
Yes, both still pending
02/12 Dirk Behme [U-Boot] [PATCH 7/7 v2] OMAP3: Clean up MMC code
Is replaced by v3 below. Can be removed.
02/12 Dirk Behme [U-Boot] [PATCH 1/7 v2] OMAP3: Overo: Clean up pin mux and GPIO configuration 02/12 Dirk Behme [U-Boot] [PATCH 6/7 v2] OMAP3: Add OMAP3 core changes for MUSB 02/12 Dirk Behme [U-Boot] [PATCH 2/7 v2] OMAP3: Beagle: Add board revision detection
Yes, all three still pending.
02/12 Dirk Behme Re: [U-Boot] [PATCH 5/7] OMAP3: Add serial number based on die ID
No patch, only discussion. Can be removed from this list.
02/12 Dirk Behme [U-Boot] [PATCH 5/7 v2] OMAP3: Add serial number based on die ID
Yes, still pending.
02/13 Grzegorz Bernacki [U-Boot] [PATCH v6] Add support for the digsy MTC board. 02/13 Mark Jackson [U-Boot] [PATCH 1/1 v2] Setup extra MIMC200 chip selects 02/16 Fabio Porcedda Re: [U-Boot] Atmel AT91 USB Device Controller Driver 02/17 Hugo Villeneuve Re: [U-Boot] [PATCH 1/1] ARM DaVinci: Add common peripherals andmodules enable functions. 02/19 ksi@koi8.net [U-Boot] [PATCH] Davinci I2C code cleanup 02/19 Tom Re: [U-Boot] [PATCH] ARM:OMAP3 Change mmc_init to mmc_legacy_init
Already applied. Please remove from this list.
02/20 yanfeng qin [U-Boot] [PATH] ARM:OMAP3 Add OTG host support 02/20 yanfeng qin [U-Boot] [PATCH] ARM:OMAP3 Add OTG host support
can't apply and need fix
Yes. Both can be removed from this list. They are not against anything what is available in any mainline git and remove a lot functionality as already mentioned.
02/20 Dirk Behme [U-Boot] [PATCH 7/7 v3] OMAP3: Clean up MMC code
Yes, still pending. Replaces v2 above.
Conclusion for OMAP3: Still open:
02/12 Dirk Behme [U-Boot] [PATCH 0/7 v2] OMAP3: Add some additional improvements and fixes 02/12 Dirk Behme [U-Boot] [PATCH 1/7 v2] OMAP3: Overo: Clean up pin mux and GPIO configuration 02/12 Dirk Behme [U-Boot] [PATCH 2/7 v2] OMAP3: Beagle: Add board revision detection 02/12 Dirk Behme [U-Boot] [PATCH 3/7 v2] OMAP3: Add OMAP3 auto detection 02/12 Dirk Behme [U-Boot] [PATCH 4/7 v2] OMAP3: Pandora: Update pin mux 02/12 Dirk Behme [U-Boot] [PATCH 5/7 v2] OMAP3: Add serial number based on die ID 02/12 Dirk Behme [U-Boot] [PATCH 6/7 v2] OMAP3: Add OMAP3 core changes for MUSB 02/20 Dirk Behme [U-Boot] [PATCH 7/7 v3] OMAP3: Clean up MMC code
All other entries with "OMAP3" in subject in this list can be removed.
Additionally (not at this list), we *really* like to get an ARM mach-types update
http://lists.denx.de/pipermail/u-boot/2009-February/046756.html http://lists.denx.de/pipermail/u-boot/2009-February/046755.html
Many thanks for tracking and this reminder,
Dirk
Btw.: Wolfgang: How do you maintain this list? Manually? Or any script? I always like to learn new things ;)