Hi,
Am 18.01.2024 um 09:33 schrieb Ivan T. Ivanov iivanov@suse.de:
I actually just did that. Installed a fresh Tumbleweed on a microSD card, booted it up with a rpi4 and after installing all necessary build tools I applied your patches to u-boot 2024.01 sources, and then executed these two commands to let it compile a u-boot.bin file which I then put in /boot/efi to replace the u-boot.bin which is/was already there. Then I pulled the SD card and moved it over to the RaspberryPi5 in trying to get it booted up. However, again no HDMI output at all and unfortunately also the serial output on the debug probe does not show U-boot popping up at all. Interestingly, using the patched u-boot.bin with a RaspberryPi4 still works and it boots up perfectly fine, but not with the RaspberryPi5 I have here.
Any idea why this might be the case here while you report that the above mentioned procedure works for you? In fact, the RaspberryPi5 I have here is a 8GB model and with the rpi-eeprom version from 2024/01/05 [1] in case this might be relevant.
EEPROM version on mine device is older[1], but I suspect that size of the RAM is what make a difference, mine have only 4GB of RAM.
This can be also of course the reason why it works for you while it doesn’t for me.
I am afraid you will have to connect that UART debug cable and share what is the memory map on your device :-)
No problem. Here is the output of the RPI bootloader boot up until the system stalls:
— cut here — RPi: BOOTSYS release VERSION:30cc5f37 DATE: 2024/01/05 TIME: 15:57:40 BOOTMODE: 0x06 partition 0 build-ts BUILD_TIMESTAMP=1704470260 serial 9127ae99 boardrev d04170 stc 923866 AON_RESET: 00000003 PM_RSTS 00001000 RP1_BOOT chip ID: 0x20001927 PM_RSTS: 0x00001000 part 00000000 reset_info 00000000 PMIC reset-event 00000000 rtc 00000000 alarm 00000000 enabled 0 uSD voltage 3.3V Initialising SDRAM 'Micron' 32Gb x2 total-size: 64 Gbit 4267 DDR 4267 1 0 64 152 RP1_BOOT chip ID: 0x20001927
RP1_BOOT chip ID: 0x20001927 RP1_BOOT: fw size 25968 PCI2 init PCI2 reset PCIe scan 00001de4:00000001 RP1_CHIP_INFO 20001927
RPi: BOOTLOADER release VERSION:30cc5f37 DATE: 2024/01/05 TIME: 15:57:40 BOOTMODE: 0x06 partition 0 build-ts BUILD_TIMESTAMP=1704470260 serial 9127ae99 boardrev d04170 stc 3892985 AON_RESET: 00000003 PM_RSTS 00001000 M.2 PCIe HAT not detected. usb_pd_init status 3 USB_PD CONFIG 0 41 Boot mode: SD (01) order f4 SD HOST: 200000000 CTL0: 0x00800000 BUS: 400000 Hz actual: 390625 HZ div: 512 (256) status: 0x1fff0000 delay: 276 SD HOST: 200000000 CTL0: 0x00800f00 BUS: 400000 Hz actual: 390625 HZ div: 512 (256) status: 0x1fff0000 delay: 276 OCR c0ff8000 [291] CID: 00035344534536344780519441cb0123 CSD: 400e00325b590001dbd37f800a404000 SD: bus-width: 4 spec: 2 SCR: 0x02458443 0x00000000 SD HOST: 200000000 CTL0: 0x00800f04 BUS: 50000000 Hz actual: 50000000 HZ div: 4 (2) status: 0x1fff0000 delay: 2 MBR: 0x00002000, 131072 type: 0x0c MBR: 0x00022000, 1024000 type: 0x82 MBR: 0x0011c000,123572224 type: 0x83 MBR: 0x00000000, 0 type: 0x00 USB-PD: src-cap PDO object1 0x0a0191f4 Current 5000 mA Voltage 5000 mV USB-PD: src-cap PDO object2 0x0002d12c Current 3000 mA Voltage 9000 mV USB-PD: src-cap PDO object3 0x0003c0e1 Current 2250 mA Voltage 12000 mV USB-PD: src-cap PDO object4 0x0004b0b4 Current 1800 mA Voltage 15000 mV Trying partition: 0 type: 16 lba: 8192 'mkfs.fat' ' V ^ ' clusters 32695 (4) rsc 4 fat-sectors 128 root dir cluster 1 sectors 32 entries 512 FAT16 clusters 32695 [sdcard] autoboot.txt not found Select partition rsts 0 C(boot_partition) 0 EEPROM config 0 result 0 Trying partition: 0 type: 16 lba: 8192 'mkfs.fat' ' V ^ ' clusters 32695 (4) rsc 4 fat-sectors 128 root dir cluster 1 sectors 32 entries 512 FAT16 clusters 32695 Read config.txt bytes 3046 hnd 0x123c Read ubootconfig.txt bytes 35 hnd 0x468 [sdcard] extraconfig.txt not found [sdcard] pieeprom.upd not found usb_max_current_enable default 0 max-current 5000 Read bcm2712-rpi-5-b.dtb bytes 79357 hnd 0x139f dt-match: compatible: raspberrypi,5-model-b match: brcm,bcm2712 dt-match: compatible: brcm,bcm2712 match: brcm,bcm2712
NOTICE: BL31: v2.6(release):v2.6-239-g2a9ede0bd NOTICE: BL31: Built : 14:26:57, Jun 22 2023 — cut here —
Best Regards,
Jens