On 27.01.20 12:37, Mauro Condarelli wrote:
Unfortunately this still doesn't work as it should.
I've been doing more tests and I found out MMC/SD *does* work, but with a ridiculously low throughput (~20KB/s) which is enough to trigger WDT loading uImage.
Adding explicit "max-frequency = <48000000>;" to .dts *seems* to cure speed problem, but makes transfer unreliable: relatively small files (<200k) usually work fine, but larger files invariably exit with error:
Error reading cluster ** Unable to read file uboot-ram.bin **
after which mmc subsystem is unusable (till next reset).
@Stefan: do MMC/SD work right on LinkIt/Gardena ? apparently neither define mmc section in .dts
I have zero experience with MMC/SD on these platforms as this IF is not used on the GARDENA board at all. So sorry, I can't help.
Thanks, Stefan
Enabling Debugging I have the following (opaque to me) output:
============================= U-Boot 2020.01-00646-gdec191f2a0-dirty (Jan 27 2020 - 12:23:17 +0100)
CPU: MediaTek MT7628A ver:1 eco:2 Boot: DDR2, SPI-NOR 3-Byte Addr, CPU clock from XTAL Clock: CPU: 580MHz, Bus: 193MHz, XTAL: 40MHz Model: VoCore2 DRAM: 128 MiB Bound device mod_exp_sw to root_driver Bound device clk48m@0 to root_driver ofnode_read_u32_array: ranges: Bound device resetctl-reboot to palmbus@10000000 Bound device clkctrl@0x2c to palmbus@10000000 Bound device rstctrl@0x34 to palmbus@10000000 ofnode_read_bool: gpio-controller: false ofnode_read_bool: gpio-controller: false Bound device p0led to pin_state Bound device pin_state to pinctrl@60 ofnode_read_bool: gpio-controller: false Bound device spi_single_pins to pinctrl@60 ofnode_read_bool: gpio-controller: false ofnode_read_bool: gpio-controller: false Bound device spi_master_pins to spi_dual_pins ofnode_read_bool: gpio-controller: false Bound device spi_cs1_pin to spi_dual_pins Bound device spi_dual_pins to pinctrl@60 ofnode_read_bool: gpio-controller: false Bound device uart0_pins to pinctrl@60 ofnode_read_bool: gpio-controller: false Bound device uart1_pins to pinctrl@60 ofnode_read_bool: gpio-controller: false Bound device uart2_pins to pinctrl@60 ofnode_read_bool: gpio-controller: false Bound device uart2_pwm_pins to pinctrl@60 ofnode_read_bool: gpio-controller: false Bound device i2c_pins to pinctrl@60 ofnode_read_bool: gpio-controller: false ofnode_read_bool: gpio-controller: false Bound device ephy4_1_dis to ephy_iot_mode ofnode_read_bool: gpio-controller: false Bound device ephy0_en to ephy_iot_mode Bound device ephy_iot_mode to pinctrl@60 ofnode_read_bool: gpio-controller: false ofnode_read_bool: gpio-controller: false Bound device ephy4_1_en to ephy_router_mode ofnode_read_bool: gpio-controller: false Bound device ephy0_en to ephy_router_mode Bound device ephy_router_mode to pinctrl@60 ofnode_read_bool: gpio-controller: false ofnode_read_bool: gpio-controller: false Bound device ephy4_1_dis to sd_iot_mode ofnode_read_bool: gpio-controller: false Bound device sdxc_en to sd_iot_mode ofnode_read_bool: gpio-controller: false Bound device sdxc_iot_mode to sd_iot_mode ofnode_read_bool: gpio-controller: false Bound device sd_clk_pad to sd_iot_mode Bound device sd_iot_mode to pinctrl@60 ofnode_read_bool: gpio-controller: false ofnode_read_bool: gpio-controller: false Bound device sdxc_router_mode to sd_router_mode ofnode_read_bool: gpio-controller: false Bound device sdxc_map_pins to sd_router_mode ofnode_read_bool: gpio-controller: false Bound device sd_clk_pad to sd_router_mode Bound device sd_router_mode to pinctrl@60 ofnode_read_bool: gpio-controller: false ofnode_read_bool: gpio-controller: false Bound device ephy4_1_dis to emmc_iot_8bit_mode ofnode_read_bool: gpio-controller: false Bound device emmc_en to emmc_iot_8bit_mode ofnode_read_bool: gpio-controller: false Bound device emmc_iot_mode to emmc_iot_8bit_mode ofnode_read_bool: gpio-controller: false Bound device emmc_d4_d5 to emmc_iot_8bit_mode ofnode_read_bool: gpio-controller: false Bound device emmc_d6 to emmc_iot_8bit_mode ofnode_read_bool: gpio-controller: false Bound device emmc_d7 to emmc_iot_8bit_mode ofnode_read_bool: gpio-controller: false Bound device sd_clk_pad to emmc_iot_8bit_mode Bound device emmc_iot_8bit_mode to pinctrl@60 Bound device pinctrl@60 to palmbus@10000000 Bound device watchdog@100 to palmbus@10000000 Bound device PA to gpio@600 Bound device PB to gpio@600 Bound device PC to gpio@600 Bound device gpio@600 to palmbus@10000000 ofnode_read_u32: reg: 0x0 (0) ofnode_read_u32: spi-max-frequency: 0x17d7840 (25000000) ofnode_read_bool: spi-cpol: false ofnode_read_bool: spi-cpha: false ofnode_read_bool: spi-cs-high: false ofnode_read_bool: spi-3wire: false ofnode_read_bool: spi-half-duplex: false ofnode_read_u32: spi-tx-bus-width: (not found) ofnode_read_u32: spi-rx-bus-width: (not found) Bound device spi-flash@0 to spi@b00 Bound device spi@b00 to palmbus@10000000 Bound device uartlite@c00 to palmbus@10000000 Bound device uart1@d00 to palmbus@10000000 Bound device uart2@e00 to palmbus@10000000 Bound device palmbus@10000000 to root_driver Bound device ehci@101c0000 to root_driver Bound device mmc@10130000.blk to mmc@10130000 Bound device mmc@10130000 to root_driver ofnode_read_string: label: vocore:power Bound device power to leds Bound device leds to root_driver parsing subnodes of "chosen" ofnode_read_u32: timeout-sec: (not found) WDT: Started with servicing (60s timeout) MMC: Req index out of range ofnode_read_u32: bus-width: 0x4 (4) ofnode_read_u32: max-frequency: 0x2dc6c00 (48000000) ofnode_read_bool: cap-sd-highspeed: true ofnode_read_bool: cap-mmc-highspeed: true ofnode_read_bool: sd-uhs-sdr12: false ofnode_read_bool: sd-uhs-sdr25: false ofnode_read_bool: sd-uhs-sdr50: false ofnode_read_bool: sd-uhs-sdr104: false ofnode_read_bool: sd-uhs-ddr50: false ofnode_read_bool: mmc-ddr-1_8v: false ofnode_read_bool: mmc-ddr-1_2v: false ofnode_read_bool: mmc-hs200-1_8v: false ofnode_read_bool: mmc-hs200-1_2v: false ofnode_read_bool: mmc-hs400-1_8v: false ofnode_read_bool: mmc-hs400-1_2v: false ofnode_read_bool: mmc-hs400-enhanced-strobe: false ofnode_read_bool: non-removable: false ofnode_read_bool: cd-inverted: false ofnode_read_bool: broken-cd: false ofnode_read_bool: no-1-8-v: false ofnode_read_u32: clock-frequency: 0x2dc6c00 (48000000) ofnode_read_u32: hs400-ds-delay: (not found) ofnode_read_u32: cmd_int_delay: (not found) ofnode_read_u32: write_int_delay: (not found) ofnode_read_u32: latch-ck: (not found) ofnode_read_u32: r_smpl: 0x1 (1) ofnode_read_u32: builtin-cd: 0x1 (1) ofnode_read_bool: cd-active-high: false mmc@10130000: 0 Loading Environment from FAT... CMD_SEND:0 ARG 0x00000000 MMC_RSP_NONE CMD_SEND:8 ARG 0x000001aa MMC_RSP_R1,5,6,7 0x000001aa CMD_SEND:55 ARG 0x00000000 MMC_RSP_R1,5,6,7 0x00000120 CMD_SEND:41 ARG 0x40300000 MMC_RSP_R3,4 0x00ff8000 CMD_SEND:55 ARG 0x00000000 MMC_RSP_R1,5,6,7 0x00000120 CMD_SEND:41 ARG 0x40300000 MMC_RSP_R3,4 0xc0ff8000 CMD_SEND:2 ARG 0x00000000 MMC_RSP_R2 0x744a6055 0x53442020 0x10427128 0x09013619
DUMPING DATA 000 - 74 4a 60 55 004 - 53 44 20 20 008 - 10 42 71 28 012 - 09 01 36 19 CMD_SEND:3 ARG 0x00000000 MMC_RSP_R1,5,6,7 0x59b40520 CMD_SEND:9 ARG 0x59b40000 MMC_RSP_R2 0x400e0032 0x5b590000 0x3c1d7f80 0x0a400063
DUMPING DATA 000 - 40 0e 00 32 004 - 5b 59 00 00 008 - 3c 1d 7f 80 012 - 0a 40 00 63 CMD_SEND:7 ARG 0x59b40000 MMC_RSP_R1,5,6,7 0x00000700 CMD_SEND:55 ARG 0x59b40000 MMC_RSP_R1,5,6,7 0x00000920 CMD_SEND:51 ARG 0x00000000 MMC_RSP_R1,5,6,7 0x00000920 CMD_SEND:6 ARG 0x00fffff1 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:55 ARG 0x59b40000 MMC_RSP_R1,5,6,7 0x00000920 CMD_SEND:6 ARG 0x00000002 MMC_RSP_R1,5,6,7 0x00000920 CMD_SEND:6 ARG 0x80fffff1 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:55 ARG 0x59b40000 MMC_RSP_R1,5,6,7 0x00000920 CMD_SEND:13 ARG 0x00000000 MMC_RSP_R1,5,6,7 0x00000920 CMD_SEND:16 ARG 0x00000200 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:17 ARG 0x00000000 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:16 ARG 0x00000200 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:17 ARG 0x00000000 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:16 ARG 0x00000200 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:17 ARG 0x00000800 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:16 ARG 0x00000200 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:18 ARG 0x00000a04 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:12 ARG 0x00000000 MMC_RSP_R1b 0x00000b00 *** Warning - bad CRC, using default environment
Model: VoCore2 => ls mmc 0:1 CMD_SEND:16 ARG 0x00000200 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:17 ARG 0x00000000 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:16 ARG 0x00000200 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:17 ARG 0x00000800 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:16 ARG 0x00000200 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:18 ARG 0x00000a04 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:12 ARG 0x00000000 MMC_RSP_R1b 0x00000b00 179840 uboot-ram_20170210.bin 179840 uboot-ram.bin 183272 uboot-rom_20170213.bin 183272 uboot-rom_20170423.bin 1819846 uImage.initram 1473392 initram.cpio.xz 1819846 uImage
7 file(s), 0 dir(s)
=> load mmc 0:1 85000000 uboot-ram.bin CMD_SEND:16 ARG 0x00000200 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:17 ARG 0x00000000 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:16 ARG 0x00000200 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:17 ARG 0x00000800 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:16 ARG 0x00000200 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:18 ARG 0x00000a04 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:12 ARG 0x00000000 MMC_RSP_R1b 0x00000b00 CMD_SEND:16 ARG 0x00000200 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:18 ARG 0x00000804 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:12 ARG 0x00000000 MMC_RSP_R1b 0x00000b00 CMD_SEND:16 ARG 0x00000200 MMC_RSP_R1,5,6,7 0x00000900 CMD_SEND:18 ARG 0x00000b88 RET -5 Error reading cluster ** Unable to read file uboot-ram.bin ** =>
============================= Any hint welcome (I'm out of my depth, here).
Thanks in Advance Mauro
On 1/25/20 10:12 PM, Mauro Condarelli wrote:
Small patch series to add support for VoCore/VoCore2 board.
VoCore is open hardware and runs OpenWrt/LEDE. It has WIFI, USB, UART, 20+ GPIOs but is only one inch square. It will help you to make a smart house, study embedded system or even make the tiniest router in the world.
Details about this SoM can be found at "https://vocore.io/v2.html".
Signed-off-by: Mauro Condarelli mc5686@mclink.it
Changes in v3:
- based on top of Weijie Gao patchset: "[v3,xx/20]Refactor the architecture parts of mt7628"
Changes in v2:
Removed some dead code
Changed Author to my full name (no nick)
Removed unwanted fixup to .dts generation (not my call).
Fixed commit message
Fixed various variables/filenames to include Vendor name
Changed Vendor name (Vonger -> Vocore)
MAINTAINERS | 1 + arch/mips/dts/Makefile | 1 + arch/mips/dts/mt7628a.dtsi | 56 ++++------------- arch/mips/dts/vocore_vocore2.dts | 76 +++++++++++++++++++++++ arch/mips/mach-mtmips/Kconfig | 8 +++ board/vocore/vocore2/Kconfig | 12 ++++ board/vocore/vocore2/Makefile | 3 + board/vocore/vocore2/board.c | 33 ++++++++++ configs/vocore2_defconfig | 100 +++++++++++++++++++++++++++++++ include/configs/vocore2.h | 66 ++++++++++++++++++++ 10 files changed, 311 insertions(+), 45 deletions(-) create mode 100644 arch/mips/dts/vocore_vocore2.dts create mode 100644 board/vocore/vocore2/Kconfig create mode 100644 board/vocore/vocore2/Makefile create mode 100644 board/vocore/vocore2/board.c create mode 100644 configs/vocore2_defconfig create mode 100644 include/configs/vocore2.h
diff --git a/MAINTAINERS b/MAINTAINERS index 7d2729dfb0..aef0f4a26d 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1,3 +1,4 @@ +source /home/mcon/.basheditor/remote-debugging-v1.sh localhost 33333 #BASHEDITOR-TMP-REMOTE-DEBUGGING-END|Origin line: Descriptions of section entries:
P: Person (obsolete) diff --git a/arch/mips/dts/Makefile b/arch/mips/dts/Makefile index cbd0c8bc8b..f711e9fb59 100644 --- a/arch/mips/dts/Makefile +++ b/arch/mips/dts/Makefile @@ -23,6 +23,7 @@ dtb-$(CONFIG_BOARD_NETGEAR_DGND3700V2) += netgear,dgnd3700v2.dtb dtb-$(CONFIG_BOARD_SAGEM_FAST1704) += sagem,f@st1704.dtb dtb-$(CONFIG_BOARD_SFR_NB4_SER) += sfr,nb4-ser.dtb dtb-$(CONFIG_BOARD_TPLINK_WDR4300) += tplink_wdr4300.dtb +dtb-$(CONFIG_BOARD_VOCORE2) += vocore_vocore2.dtb dtb-$(CONFIG_TARGET_JZ4780_CI20) += ci20.dtb dtb-$(CONFIG_SOC_LUTON) += luton_pcb090.dtb luton_pcb091.dtb dtb-$(CONFIG_SOC_OCELOT) += ocelot_pcb120.dtb ocelot_pcb123.dtb diff --git a/arch/mips/dts/mt7628a.dtsi b/arch/mips/dts/mt7628a.dtsi index 6baa63add3..3d4f29e0c5 100644 --- a/arch/mips/dts/mt7628a.dtsi +++ b/arch/mips/dts/mt7628a.dtsi @@ -7,6 +7,11 @@ #size-cells = <1>; compatible = "ralink,mt7628a-soc";
- resetc: reset-controller {
compatible = "ralink,rt2880-reset";#reset-cells = <1>;- };
- cpus { #address-cells = <1>; #size-cells = <0>;
@@ -61,6 +66,12 @@ u-boot,dm-pre-reloc; };
clkgate: clkgate@0x30 {reg = <0x30 0x4>;compatible = "mediatek,mediatek,mt7628-clk";#clock-cells = <1>;};- rstctrl: rstctrl@0x34 { reg = <0x34 0x4>; compatible = "mediatek,mtmips-reset";
@@ -228,32 +239,6 @@
resets = <&rstctrl MT7628_TIMER_RST>; reset-names = "wdt";
interrupt-parent = <&intc>;interrupts = <24>;};intc: interrupt-controller@200 {compatible = "ralink,rt2880-intc";reg = <0x200 0x100>;interrupt-controller;#interrupt-cells = <1>;resets = <&rstctrl MT7628_INT_RST>;reset-names = "intc";interrupt-parent = <&cpuintc>;interrupts = <2>;ralink,intc-registers = <0x9c 0xa00x6c 0xa40x80 0x78>;};memory-controller@300 {compatible = "ralink,mt7620a-memc";reg = <0x300 0x100>;};
gpio@600 {
@@ -266,9 +251,6 @@ resets = <&rstctrl MT7628_PIO_RST>; reset-names = "pio";
interrupt-parent = <&intc>;interrupts = <6>;gpio0: bank@0 { reg = <0>; compatible = "mtk,mt7621-gpio-bank";@@ -316,9 +298,6 @@ resets = <&rstctrl MT7628_UART0_RST>; reset-names = "uart0";
interrupt-parent = <&intc>;interrupts = <20>;reg-shift = <2>;@@ -334,9 +313,6 @@ resets = <&rstctrl MT7628_UART1_RST>; reset-names = "uart1";
interrupt-parent = <&intc>;interrupts = <21>;reg-shift = <2>;@@ -352,9 +328,6 @@ resets = <&rstctrl MT7628_UART2_RST>; reset-names = "uart2";
interrupt-parent = <&intc>;interrupts = <22>;reg-shift = <2>;@@ -366,8 +339,6 @@
resets = <&rstctrl MT7628_EPHY_RST>; reset-names = "ephy";
syscon = <&sysc>;};
usb_phy: usb-phy@10120000 {
@@ -376,8 +347,6 @@
#phy-cells = <0>;
ralink,sysctl = <&sysc>;- resets = <&rstctrl MT7628_UPHY_RST>; reset-names = "phy";
@@ -391,9 +360,6 @@
phys = <&usb_phy>; phy-names = "usb";
interrupt-parent = <&intc>;interrupts = <18>;};
mmc: mmc@10130000 {
diff --git a/arch/mips/dts/vocore_vocore2.dts b/arch/mips/dts/vocore_vocore2.dts new file mode 100644 index 0000000000..b8fd87a3e9 --- /dev/null +++ b/arch/mips/dts/vocore_vocore2.dts @@ -0,0 +1,76 @@ +// SPDX-License-Identifier: GPL-2.0+ +/*
- Copyright (C) 2019 Mauro Condarelli mc5686@mclink.it
- */
+/dts-v1/;
+#include "mt7628a.dtsi" +#include <dt-bindings/gpio/gpio.h>
+/ {
- compatible = "vocore,vocore2", "ralink,mt7628a-soc";
- model = "VoCore2";
- aliases {
serial0 = &uart2;spi0 = &spi0;- };
- memory@0 {
device_type = "memory";reg = <0x0 0x08000000>;- };
- leds {
compatible = "gpio-leds";power {label = "vocore:power";gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;default-state = "off";};- };
- chosen {
bootargs = "console=ttyS2,115200";stdout-path = &uart2;- };
+};
+&pinctrl {
- state_default: pin_state {
p0led {groups = "p0led_a";function = "led";};- };
+};
+&uart2 {
- status = "okay";
+};
+&spi0 {
- status = "okay";
- nor0: spi-flash@0 {
#address-cells = <1>;#size-cells = <1>;compatible = "jedec,spi-nor";spi-max-frequency = <25000000>;reg = <0>;- };
+};
+ð {
- pinctrl-names = "default";
- pinctrl-0 = <&ephy_iot_mode>;
- mediatek,poll-link-phy = <0>;
+};
+&mmc {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&sd_iot_mode>;
- pinctrl-1 = <&sd_iot_mode>;
+}; diff --git a/arch/mips/mach-mtmips/Kconfig b/arch/mips/mach-mtmips/Kconfig index bcd635f438..489e466daf 100644 --- a/arch/mips/mach-mtmips/Kconfig +++ b/arch/mips/mach-mtmips/Kconfig @@ -83,6 +83,13 @@ config BOARD_MT7628_RFB SPI-NOR flash, 1 built-in switch with 5 ports, 1 UART, 1 USB host, 1 SDXC, 1 PCIe socket and JTAG pins.
+config BOARD_VOCORE2
bool "VoCore2"
depends on SOC_MT7628
help
VoCore VoCore2 board has a MT7628 SoC with 128 MiB of RAMand 16 MiB of flash (SPI).endchoice
config SPL_UART2_SPIS_PINMUX
@@ -96,5 +103,6 @@ config SPL_UART2_SPIS_PINMUX source "board/gardena/smart-gateway-mt7688/Kconfig" source "board/mediatek/mt7628/Kconfig" source "board/seeed/linkit-smart-7688/Kconfig" +source "board/vocore/vocore2/Kconfig"
endmenu diff --git a/board/vocore/vocore2/Kconfig b/board/vocore/vocore2/Kconfig new file mode 100644 index 0000000000..baeff31b69 --- /dev/null +++ b/board/vocore/vocore2/Kconfig @@ -0,0 +1,12 @@ +if BOARD_VOCORE2
+config SYS_BOARD
- default "vocore2"
+config SYS_VENDOR
- default "vocore"
+config SYS_CONFIG_NAME
- default "vocore2"
+endif diff --git a/board/vocore/vocore2/Makefile b/board/vocore/vocore2/Makefile new file mode 100644 index 0000000000..70cd7a8e56 --- /dev/null +++ b/board/vocore/vocore2/Makefile @@ -0,0 +1,3 @@ +# SPDX-License-Identifier: GPL-2.0+
+obj-y += board.o diff --git a/board/vocore/vocore2/board.c b/board/vocore/vocore2/board.c new file mode 100644 index 0000000000..d387715d14 --- /dev/null +++ b/board/vocore/vocore2/board.c @@ -0,0 +1,33 @@ +// SPDX-License-Identifier: GPL-2.0+ +/*
- Copyright (C) 2019 Mauro Condarelli mc5686@mclink.it
- Note: this is largely copied from:
board/seeed/linkit_smart_7688/board.c
Copyright (C) 2018 Stefan Roese <sr@denx.de>- */
+#include <common.h> +#include <asm/io.h>
+#define MT76XX_GPIO1_MODE 0x10000060
+void board_debug_uart_init(void) +{
- void __iomem *gpio_mode;
- /* Select UART2 mode instead of GPIO mode (default) */
- gpio_mode = ioremap_nocache(MT76XX_GPIO1_MODE, 0x100);
- clrbits_le32(gpio_mode, GENMASK(27, 26));
+}
+int board_early_init_f(void) +{
- /*
* The pin muxing of UART2 also needs to be done, if debug uart* is not enabled. So we need to call this function here as well.*/- board_debug_uart_init();
- return 0;
+} diff --git a/configs/vocore2_defconfig b/configs/vocore2_defconfig new file mode 100644 index 0000000000..04c7a6a6f5 --- /dev/null +++ b/configs/vocore2_defconfig @@ -0,0 +1,100 @@ +CONFIG_MIPS=y +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_ENV_SIZE=0x1000 +CONFIG_SPL_SERIAL_SUPPORT=y +CONFIG_SPL_SYS_MALLOC_F_LEN=0x20000 +CONFIG_NR_DRAM_BANKS=1 +CONFIG_SPL=y +CONFIG_ARCH_MTMIPS=y +CONFIG_BOARD_VOCORE2=y +CONFIG_SPL_UART2_SPIS_PINMUX=y +CONFIG_RESTORE_EXCEPTION_VECTOR_BASE=y +CONFIG_MIPS_BOOT_FDT=y +CONFIG_ENV_VARS_UBOOT_CONFIG=y +CONFIG_SYS_BOOT_GET_CMDLINE=y +CONFIG_SYS_BOOT_GET_KBD=y +CONFIG_FIT=y +CONFIG_FIT_SIGNATURE=y +CONFIG_LEGACY_IMAGE_FORMAT=y +CONFIG_OF_STDOUT_VIA_ALIAS=y +# CONFIG_ARCH_FIXUP_FDT_MEMORY is not set +CONFIG_USE_BOOTARGS=y +CONFIG_LOGLEVEL=8 +CONFIG_SYS_CONSOLE_INFO_QUIET=y +CONFIG_VERSION_VARIABLE=y +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_BOARD_EARLY_INIT_F=y +CONFIG_SPL_SYS_MALLOC_SIMPLE=y +CONFIG_SPL_NOR_SUPPORT=y +CONFIG_HUSH_PARSER=y +# CONFIG_AUTOBOOT is not set +CONFIG_CMD_LICENSE=y +# CONFIG_BOOTM_NETBSD is not set +# CONFIG_BOOTM_PLAN9 is not set +# CONFIG_BOOTM_RTEMS is not set +# CONFIG_BOOTM_VXWORKS is not set +# CONFIG_CMD_ELF is not set +# CONFIG_CMD_XIMG is not set +# CONFIG_CMD_CRC32 is not set +CONFIG_CMD_MEMINFO=y +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_GPT_RENAME=y +# CONFIG_CMD_LOADB is not set +# CONFIG_CMD_LOADS is not set +CONFIG_CMD_MMC=y +CONFIG_CMD_MTD=y +CONFIG_CMD_PART=y +CONFIG_CMD_SPI=y +CONFIG_CMD_USB=y +CONFIG_CMD_WDT=y +CONFIG_CMD_FAT=y +CONFIG_CMD_FS_GENERIC=y +CONFIG_CMD_MTDPARTS=y +CONFIG_MTDIDS_DEFAULT="nor0=spi0.0" +CONFIG_MTDPARTS_DEFAULT="spi0.0:312k(u-boot),4k(env),4k(factory),2368k(kernel),-(filesystem)" +# CONFIG_SPL_DOS_PARTITION is not set +# CONFIG_SPL_EFI_PARTITION is not set +CONFIG_DEFAULT_DEVICE_TREE="vocore_vocore2" +CONFIG_ENV_IS_IN_FAT=y +CONFIG_ENV_FAT_INTERFACE="mmc" +CONFIG_ENV_FAT_DEVICE_AND_PART="0:1" +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y +# CONFIG_NET is not set +CONFIG_SPL_DM=y +# CONFIG_DM_DEVICE_REMOVE is not set +CONFIG_LED=y +CONFIG_LED_BLINK=y +CONFIG_LED_GPIO=y +CONFIG_MMC=y +CONFIG_DM_MMC=y +# CONFIG_MMC_HW_PARTITIONING is not set +CONFIG_MMC_MTK=y +CONFIG_MTD=y +CONFIG_SPI_FLASH_SFDP_SUPPORT=y +CONFIG_SPI_FLASH_GIGADEVICE=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_SPANSION=y +CONFIG_SPI_FLASH_STMICRO=y +CONFIG_SPI_FLASH_WINBOND=y +CONFIG_SPI_FLASH_MTD=y +# CONFIG_DM_ETH is not set +# CONFIG_RAM_ROCKCHIP_DEBUG is not set +CONFIG_SPECIFY_CONSOLE_INDEX=y +CONFIG_CONS_INDEX=3 +CONFIG_SPI=y +CONFIG_MT7621_SPI=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_STORAGE=y +CONFIG_WDT=y +CONFIG_WDT_MT7621=y +CONFIG_FS_EXT4=y +CONFIG_LZMA=y +CONFIG_LZO=y +CONFIG_FDT_FIXUP_PARTITIONS=y diff --git a/include/configs/vocore2.h b/include/configs/vocore2.h new file mode 100644 index 0000000000..602a78d0d5 --- /dev/null +++ b/include/configs/vocore2.h @@ -0,0 +1,66 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/*
- Copyright (C) 2019 Mauro Condarelli mc5686@mclink.it
- */
+#ifndef __VOCORE2_CONFIG_H__ +#define __VOCORE2_CONFIG_H__
+/* CPU */ +#define CONFIG_SYS_MIPS_TIMER_FREQ 290000000
+/* RAM */ +#define CONFIG_SYS_SDRAM_BASE 0x80000000
+#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE + 0x100000
+#define CONFIG_SYS_INIT_SP_OFFSET 0x400000
+/* SPL */ +#if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD) +#define CONFIG_SKIP_LOWLEVEL_INIT +#endif
+#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE +#define CONFIG_SPL_BSS_START_ADDR 0x80010000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x10000 +#define CONFIG_SPL_MAX_SIZE 0x10000
+/* Dummy value */ +#define CONFIG_SYS_UBOOT_BASE 0
+/* Serial SPL */ +#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_SERIAL_SUPPORT) +#define CONFIG_SYS_NS16550_MEM32 +#define CONFIG_SYS_NS16550_CLK 40000000 +#define CONFIG_SYS_NS16550_REG_SIZE -4 +#define CONFIG_SYS_NS16550_COM3 0xb0000e00 +#define CONFIG_CONS_INDEX 3
+#endif
+/* UART */ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, \
230400, 460800, 921600 }+/* RAM */ +#define CONFIG_SYS_MEMTEST_START 0x80100000 +#define CONFIG_SYS_MEMTEST_END 0x80400000
+/* Memory usage */ +#define CONFIG_SYS_MAXARGS 64 +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) +#define CONFIG_SYS_BOOTPARAMS_LEN (128 * 1024) +#define CONFIG_SYS_CBSIZE 512
+/* U-Boot */ +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+/* Environment settings */ +#if defined(CONFIG_MTDIDS_DEFAULT) && defined(CONFIG_MTDPARTS_DEFAULT) +#define CONFIG_EXTRA_ENV_SETTINGS \
- "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
- "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0"
+#endif
+#endif//__VOCORE2_CONFIG_H__
Viele Grüße, Stefan