Hi Paul, Thanks for the reply. I am very new to the 32bit world.
Currently I am using the files for the MPC8313ERDB as a basis. I have altered srdam.c and my version of MPC8313ERDB.h to reflect my new DDR2 layout. I have 4 ICs, 2 on each CS.
The settings you mentioned below are.. #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM .. in my version of MPC8313ERDB.h file. I believe these are referring to the eLocalBus base addresses for Local Bus Chip Selects?
My DDR2 ram is using the MPC8313 DDR memory controller and I have added.....
#define CONFIG_SYS_DDR_CS1_CONFIG (CSCONFIG_EN \ | CSCONFIG_ODT_RD_ONLY_CURRENT \ | CSCONFIG_ODT_WR_ONLY_CURRENT \ | CSCONFIG_BANK_BIT_3 \ | CSCONFIG_ROW_BIT_14 \ | CSCONFIG_COL_BIT_10) /* 0x80114202 */ .... to my version of the MPC8313ERDB.h file.
And, I have altered sdram.c to look like this...
/* Local address Window for DDR CS0 */ im->sysconf.ddrlaw[0].bar = CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000; im->sysconf.ddrlaw[0].ar = LBLAWAR_EN | (msize_log2 - 1);
/* Local address Window for DDR CS1 */ im->sysconf.ddrlaw[1].bar = (CONFIG_SYS_DDR_SDRAM_BASE + msize) & 0xfffff000; im->sysconf.ddrlaw[1].ar = LBLAWAR_EN | (msize_log2 - 1); im->sysconf.ddrcdr = CONFIG_SYS_DDRCDR_VALUE;
/* * Erratum DDR3 requires a 50ms delay after clearing DDRCDR[DDR_cfg], * or the DDR2 controller may fail to initialize correctly. */ __udelay(50000);
#if ((CONFIG_SYS_DDR_SDRAM_BASE & 0x00FFFFFF) != 0) #warning Chip select bounds is only configurable in 16MB increments #endif /* Set CS bounds for CS0 */ im->ddr.csbnds[0].csbnds = ((CONFIG_SYS_DDR_SDRAM_BASE >> CSBNDS_SA_SHIFT) & CSBNDS_SA) | (((CONFIG_SYS_DDR_SDRAM_BASE + msize - 1) >> CSBNDS_EA_SHIFT) & CSBNDS_EA); /* Set CS bounds for CS1 */ im->ddr.csbnds[1].csbnds = (((CONFIG_SYS_DDR_SDRAM_BASE + msize) >> CSBNDS_SA_SHIFT) & CSBNDS_SA) | (((CONFIG_SYS_DDR_SDRAM_BASE + (2*msize) - 1) >> CSBNDS_EA_SHIFT) & CSBNDS_EA); /* Enable bank 0. */ im->ddr.cs_config[0] = CONFIG_SYS_DDR_CS0_CONFIG;
/* Enable bank 1. */ im->ddr.cs_config[1] = CONFIG_SYS_DDR_CS1_CONFIG;
My hardware has not been delivered yet so I can't test the modifications!
So I don't know if they might work?!
Best Regards, Scott
-----Original Message----- From: paul.gortmaker@gmail.com [mailto:paul.gortmaker@gmail.com] On Behalf Of Paul Gortmaker Sent: 08 February 2012 04:46 To: Scott Larson Cc: u-boot@lists.denx.de Subject: Re: [U-Boot] MPC8313 DDR2 configuration
On Tue, Feb 7, 2012 at 11:52 AM, Scott Larson slarson@a2etech.com wrote:
Hi,
Looking for help on DDR2 configuration in u-boot.
I have the MPC8313ERDB from Freescale. It has 128Mbytes of DDR2 ram. The existing 128MByte that uses only CS0.
I have a new board design to bring up.
The timing parameters are all ok but I need some guidance on changing the settings to suit my memory configuration.
My board has 512Mbytes on CS0 and 512Mbytes on CS1.
Changes need to be made to files MPC8313ERDB.h and sdram.c
SODIMM with SPD? Autoconfig with CONFIG_SPD_EEPROM is nice compared to hard coding values, if you can use it. I'm pretty sure it works fine on sbc8349 board.
I have made all the row and column size and block address pin settings ok. I have set DDR size to 512Mbytes (per Chip Select).
I need some guidance on the setting for CS1 bank of ram.
Have you created the CONFIG_SYS_BR1_PRELIM and the CONFIG_SYS_OR1_PRELIM defines in your board header?
If you copied these from a reference platform, they may still be populated with settings appropriate for flash up at the top of memory instead of DDR2 settings for your 2nd bank...
P.
thanks
Scott
U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot