This code allows the DDR DRAM size to be detected at runtime. The RAM size is stored into two scratch registers, from which it is then fetched in U-Boot.
Signed-off-by: Marek Vasut marek.vasut@gmail.com --- board/denx/m28evk/Makefile | 7 ++++++- board/denx/m28evk/m28evk.c | 18 ++++++++++++++++-- board/denx/m28evk/mem_init.c | 27 +++++++++++++++++++++++++++ include/configs/m28evk.h | 2 +- 4 files changed, 50 insertions(+), 4 deletions(-)
V2: Drop clean and distclean targets V3: Drop $(obj) in front of memsize.c target
diff --git a/board/denx/m28evk/Makefile b/board/denx/m28evk/Makefile index 47229e6..b6f002f 100644 --- a/board/denx/m28evk/Makefile +++ b/board/denx/m28evk/Makefile @@ -30,7 +30,7 @@ COBJS := m28evk.o endif
ifdef CONFIG_SPL_BUILD -COBJS := mem_init.o mmc_boot.o power_init.o +COBJS := mem_init.o mmc_boot.o power_init.o memsize.o endif
SRCS := $(COBJS:.o=.c) @@ -41,6 +41,11 @@ $(LIB): $(obj).depend $(OBJS)
all: $(ALL)
+ifdef CONFIG_SPL_BUILD +memsize.c: + ln -sf $(TOPDIR)/common/memsize.c $@ +endif + #########################################################################
# defines $(obj).depend target diff --git a/board/denx/m28evk/m28evk.c b/board/denx/m28evk/m28evk.c index 118e222..168ceeb 100644 --- a/board/denx/m28evk/m28evk.c +++ b/board/denx/m28evk/m28evk.c @@ -63,10 +63,24 @@ int board_init(void) return 0; }
+#define HW_DIGCTRL_SCRATCH0 0x8001c280 +#define HW_DIGCTRL_SCRATCH1 0x8001c290 int dram_init(void) { - /* dram_init must store complete ramsize in gd->ram_size */ - gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE); + uint32_t sz[2]; + + sz[0] = readl(HW_DIGCTRL_SCRATCH0); + sz[1] = readl(HW_DIGCTRL_SCRATCH1); + + if (sz[0] != sz[1]) { + printf("MX28:\n" + "Error, the RAM size in HW_DIGCTRL_SCRATCH0 and\n" + "HW_DIGCTRL_SCRATCH1 is not the same. Please\n" + "verify these two registers contain valid RAM size!\n"); + hang(); + } + + gd->ram_size = sz[0]; return 0; }
diff --git a/board/denx/m28evk/mem_init.c b/board/denx/m28evk/mem_init.c index 066fe0d..17d1f9b 100644 --- a/board/denx/m28evk/mem_init.c +++ b/board/denx/m28evk/mem_init.c @@ -165,6 +165,31 @@ void mx28_mem_setup_vddd(void) &power_regs->hw_power_vdddctrl); }
+#define HW_DIGCTRL_SCRATCH0 0x8001c280 +#define HW_DIGCTRL_SCRATCH1 0x8001c290 +void data_abort_memdetect_handler(void) __attribute__((naked)); +void data_abort_memdetect_handler(void) +{ + asm volatile("subs pc, r14, #4"); +} + +void mx28_mem_get_size(void) +{ + uint32_t sz, da; + uint32_t *vt = (uint32_t *)0x20; + + /* Replace the DABT handler. */ + da = vt[4]; + vt[4] = (uint32_t)&data_abort_memdetect_handler; + + sz = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE); + writel(sz, HW_DIGCTRL_SCRATCH0); + writel(sz, HW_DIGCTRL_SCRATCH1); + + /* Restore the old DABT handler. */ + vt[4] = da; +} + void mx28_mem_init(void) { struct mx28_clkctrl_regs *clkctrl_regs = @@ -210,4 +235,6 @@ void mx28_mem_init(void) early_delay(10000);
mx28_mem_setup_cpu_and_hbus(); + + mx28_mem_get_size(); } diff --git a/include/configs/m28evk.h b/include/configs/m28evk.h index 381b01e..c8b0cf5 100644 --- a/include/configs/m28evk.h +++ b/include/configs/m28evk.h @@ -81,7 +81,7 @@ */ #define CONFIG_NR_DRAM_BANKS 1 /* 2 banks of DRAM */ #define PHYS_SDRAM_1 0x40000000 /* Base address */ -#define PHYS_SDRAM_1_SIZE 0x08000000 /* 128 MB */ +#define PHYS_SDRAM_1_SIZE 0x40000000 /* Max 1 GB RAM */ #define CONFIG_STACKSIZE 0x00010000 /* 128 KB stack */ #define CONFIG_SYS_MALLOC_LEN 0x00400000 /* 4 MB for malloc */ #define CONFIG_SYS_GBL_DATA_SIZE 128 /* Initial data */