From: Icenowy Zheng icenowy@aosc.xyz
The A64 uses the AXP803 as its PMIC.
Signed-off-by: Icenowy Zheng icenowy@aosc.xyz Signed-off-by: Jernej Skrabec jernej.skrabec@siol.net ---
arch/arm/mach-sunxi/Makefile | 3 + arch/arm/mach-sunxi/pmic_bus.c | 6 +- arch/arm/mach-sunxi/rsb.c | 2 +- board/sunxi/board.c | 31 ++--- drivers/power/Kconfig | 87 ++++++++------ drivers/power/Makefile | 1 + drivers/power/axp803.c | 256 +++++++++++++++++++++++++++++++++++++++++ drivers/power/axp818.c | 2 +- include/axp803.h | 73 ++++++++++++ include/axp_pmic.h | 3 + 10 files changed, 414 insertions(+), 50 deletions(-) create mode 100644 drivers/power/axp803.c create mode 100644 include/axp803.h
diff --git a/arch/arm/mach-sunxi/Makefile b/arch/arm/mach-sunxi/Makefile index efab4811ee..861a52c6d0 100644 --- a/arch/arm/mach-sunxi/Makefile +++ b/arch/arm/mach-sunxi/Makefile @@ -19,9 +19,11 @@ endif obj-$(CONFIG_MACH_SUN6I) += prcm.o obj-$(CONFIG_MACH_SUN8I) += prcm.o obj-$(CONFIG_MACH_SUN9I) += prcm.o +obj-$(CONFIG_MACH_SUN50I) += prcm.o obj-$(CONFIG_MACH_SUN6I) += p2wi.o obj-$(CONFIG_MACH_SUN8I) += rsb.o obj-$(CONFIG_MACH_SUN9I) += rsb.o +obj-$(CONFIG_MACH_SUN50I) += rsb.o obj-$(CONFIG_MACH_SUN4I) += clock_sun4i.o obj-$(CONFIG_MACH_SUN5I) += clock_sun4i.o obj-$(CONFIG_MACH_SUN6I) += clock_sun6i.o @@ -37,6 +39,7 @@ obj-$(CONFIG_MACH_SUN9I) += clock_sun9i.o gtbus_sun9i.o obj-$(CONFIG_AXP152_POWER) += pmic_bus.o obj-$(CONFIG_AXP209_POWER) += pmic_bus.o obj-$(CONFIG_AXP221_POWER) += pmic_bus.o +obj-$(CONFIG_AXP803_POWER) += pmic_bus.o obj-$(CONFIG_AXP809_POWER) += pmic_bus.o obj-$(CONFIG_AXP818_POWER) += pmic_bus.o
diff --git a/arch/arm/mach-sunxi/pmic_bus.c b/arch/arm/mach-sunxi/pmic_bus.c index 7c57f02792..0ac64a97cf 100644 --- a/arch/arm/mach-sunxi/pmic_bus.c +++ b/arch/arm/mach-sunxi/pmic_bus.c @@ -36,7 +36,7 @@ int pmic_bus_init(void) if (!needs_init) return 0;
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER +#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP803_POWER || defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER # ifdef CONFIG_MACH_SUN6I p2wi_init(); ret = p2wi_change_to_p2wi_mode(AXP221_CHIP_ADDR, AXP221_CTRL_ADDR, @@ -62,7 +62,7 @@ int pmic_bus_read(u8 reg, u8 *data) return i2c_read(AXP152_I2C_ADDR, reg, 1, data, 1); #elif defined CONFIG_AXP209_POWER return i2c_read(AXP209_I2C_ADDR, reg, 1, data, 1); -#elif defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER +#elif defined CONFIG_AXP221_POWER || defined CONFIG_AXP803_POWER || defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER # ifdef CONFIG_MACH_SUN6I return p2wi_read(reg, data); # else @@ -77,7 +77,7 @@ int pmic_bus_write(u8 reg, u8 data) return i2c_write(AXP152_I2C_ADDR, reg, 1, &data, 1); #elif defined CONFIG_AXP209_POWER return i2c_write(AXP209_I2C_ADDR, reg, 1, &data, 1); -#elif defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER +#elif defined CONFIG_AXP221_POWER || defined CONFIG_AXP803_POWER || defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER # ifdef CONFIG_MACH_SUN6I return p2wi_write(reg, data); # else diff --git a/arch/arm/mach-sunxi/rsb.c b/arch/arm/mach-sunxi/rsb.c index 6fd11f1529..28d05e962a 100644 --- a/arch/arm/mach-sunxi/rsb.c +++ b/arch/arm/mach-sunxi/rsb.c @@ -20,7 +20,7 @@ static int rsb_set_device_mode(void);
static void rsb_cfg_io(void) { -#ifdef CONFIG_MACH_SUN8I +#if defined CONFIG_MACH_SUN8I || defined CONFIG_MACH_SUN50I sunxi_gpio_set_cfgpin(SUNXI_GPL(0), SUN8I_GPL_R_RSB); sunxi_gpio_set_cfgpin(SUNXI_GPL(1), SUN8I_GPL_R_RSB); sunxi_gpio_set_pull(SUNXI_GPL(0), 1); diff --git a/board/sunxi/board.c b/board/sunxi/board.c index b9660128e5..75e53bebbd 100644 --- a/board/sunxi/board.c +++ b/board/sunxi/board.c @@ -487,26 +487,27 @@ void sunxi_board_init(void) #endif
#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || \ - defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \ - defined CONFIG_AXP818_POWER + defined CONFIG_AXP221_POWER || defined CONFIG_AXP803_POWER || \ + defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER power_failed = axp_init();
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \ - defined CONFIG_AXP818_POWER +#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP803_POWER || \ + defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER power_failed |= axp_set_dcdc1(CONFIG_AXP_DCDC1_VOLT); #endif power_failed |= axp_set_dcdc2(CONFIG_AXP_DCDC2_VOLT); power_failed |= axp_set_dcdc3(CONFIG_AXP_DCDC3_VOLT); -#if !defined(CONFIG_AXP209_POWER) && !defined(CONFIG_AXP818_POWER) +#if !defined(CONFIG_AXP209_POWER) && !defined(CONFIG_AXP803_POWER) && \ + !defined(CONFIG_AXP818_POWER) power_failed |= axp_set_dcdc4(CONFIG_AXP_DCDC4_VOLT); #endif -#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \ - defined CONFIG_AXP818_POWER +#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP803_POWER || \ + defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT); #endif
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \ - defined CONFIG_AXP818_POWER +#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP803_POWER || \ + defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER power_failed |= axp_set_aldo1(CONFIG_AXP_ALDO1_VOLT); #endif power_failed |= axp_set_aldo2(CONFIG_AXP_ALDO2_VOLT); @@ -517,8 +518,8 @@ void sunxi_board_init(void) power_failed |= axp_set_aldo4(CONFIG_AXP_ALDO4_VOLT); #endif
-#if defined(CONFIG_AXP221_POWER) || defined(CONFIG_AXP809_POWER) || \ - defined(CONFIG_AXP818_POWER) +#if defined(CONFIG_AXP221_POWER) || defined(CONFIG_AXP803_POWER) || \ + defined(CONFIG_AXP809_POWER) || defined(CONFIG_AXP818_POWER) power_failed |= axp_set_dldo(1, CONFIG_AXP_DLDO1_VOLT); power_failed |= axp_set_dldo(2, CONFIG_AXP_DLDO2_VOLT); #if !defined CONFIG_AXP809_POWER @@ -530,13 +531,17 @@ void sunxi_board_init(void) power_failed |= axp_set_eldo(3, CONFIG_AXP_ELDO3_VOLT); #endif
-#ifdef CONFIG_AXP818_POWER +#if defined CONFIG_AXP803_POWER || defined CONFIG_AXP818_POWER power_failed |= axp_set_fldo(1, CONFIG_AXP_FLDO1_VOLT); power_failed |= axp_set_fldo(2, CONFIG_AXP_FLDO2_VOLT); +#endif + +#ifdef CONFIG_AXP818_POWER power_failed |= axp_set_fldo(3, CONFIG_AXP_FLDO3_VOLT); #endif
-#if defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER +#if defined CONFIG_AXP803_POWER || defined CONFIG_AXP809_POWER || \ + defined CONFIG_AXP818_POWER power_failed |= axp_set_sw(IS_ENABLED(CONFIG_AXP_SW_ON)); #endif #endif diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig index 64e5bc2f74..4907002ed6 100644 --- a/drivers/power/Kconfig +++ b/drivers/power/Kconfig @@ -11,8 +11,9 @@ choice depends on ARCH_SUNXI default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 + default AXP803_POWER if MACH_SUN50I default AXP818_POWER if MACH_SUN8I_A83T - default SUNXI_NO_PMIC if MACH_SUNXI_H3_H5 || MACH_SUN50I + default SUNXI_NO_PMIC if MACH_SUNXI_H3_H5
config SUNXI_NO_PMIC bool "board without a pmic" @@ -43,6 +44,13 @@ config AXP221_POWER Select this to enable support for the axp221/axp223 pmic found on most A23 and A31 boards.
+config AXP803_POWER + bool "axp803 pmic support" + depends on MACH_SUN50I + select CMD_POWEROFF + ---help--- + Say y here to enable support for the axp803 pmic found on A64 boards. + config AXP809_POWER bool "axp809 pmic support" depends on MACH_SUN9I @@ -69,25 +77,25 @@ endchoice
config AXP_DCDC1_VOLT int "axp pmic dcdc1 voltage" - depends on AXP221_POWER || AXP809_POWER || AXP818_POWER - default 3300 if AXP818_POWER + depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER + default 3300 if AXP818_POWER || MACH_SUN50I default 3000 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I ---help--- Set the voltage (mV) to program the axp pmic dcdc1 at, set to 0 to disable dcdc1. On A23 / A31 / A33 (axp221) boards dcdc1 is used for generic 3.3V IO voltage for external devices like the lcd-panal and sdcard interfaces, etc. On most boards dcdc1 is undervolted to 3.0V to - save battery. On A31 devices dcdc1 is also used for VCC-IO. On A83T - dcdc1 is used for VCC-IO, nand, usb0, sd , etc. On A80 dcdc1 normally - powers some of the pingroups, NAND/eMMC, SD/MMC, and USB OTG. + save battery. On A31 devices dcdc1 is also used for VCC-IO. On A83T and + A64 dcdc1 is used for VCC-IO, nand, usb0, sd , etc. On A80 dcdc1 + normally powers some of the pingroups, NAND/eMMC, SD/MMC, and USB OTG.
config AXP_DCDC2_VOLT int "axp pmic dcdc2 voltage" - depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER + depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER default 900 if AXP818_POWER default 1400 if AXP152_POWER || AXP209_POWER default 1200 if MACH_SUN6I - default 1100 if MACH_SUN8I + default 1100 if MACH_SUN8I || MACH_SUN50I default 0 if MACH_SUN9I ---help--- Set the voltage (mV) to program the axp pmic dcdc2 at, set to 0 to @@ -97,15 +105,17 @@ config AXP_DCDC2_VOLT On A23/A33 boards dcdc2 is used for VDD-SYS and should be 1.1V. On A80 boards dcdc2 powers the GPU and can be left off. On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V. + On A64 boards dcdc2 is used with dcdc3 for VDD-CPU and should be 1.1V.
config AXP_DCDC3_VOLT int "axp pmic dcdc3 voltage" - depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER + depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER default 900 if AXP809_POWER || AXP818_POWER default 1500 if AXP152_POWER default 1250 if AXP209_POWER default 1200 if MACH_SUN6I || MACH_SUN8I - ---help--- + default 1100 if MACH_SUN50I +---help--- Set the voltage (mV) to program the axp pmic dcdc3 at, set to 0 to disable dcdc3. On A10(s) / A13 / A20 boards with an axp209 dcdc3 is VDD-INT-DLL and @@ -114,39 +124,42 @@ config AXP_DCDC3_VOLT On A23 / A31 / A33 boards dcdc3 is VDD-CPU and should be 1.2V. On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V. On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V. + On A64 boards dcdc3 is used with dcdc2 for VDD-CPU and should be 1.1V.
config AXP_DCDC4_VOLT int "axp pmic dcdc4 voltage" - depends on AXP152_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER + depends on AXP152_POWER || AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER default 1250 if AXP152_POWER default 1200 if MACH_SUN6I default 0 if MACH_SUN8I default 900 if MACH_SUN9I + default 0 if MACH_SUN50I ---help--- Set the voltage (mV) to program the axp pmic dcdc4 at, set to 0 to disable dcdc4. On A10s boards with an axp152 dcdc4 is VDD-INT-DLL and should be 1.25V. On A31 boards dcdc4 is used for VDD-SYS and should be 1.2V. - On A23 / A33 boards dcdc4 is unused and should be disabled. + On A23 / A33 / A64 boards dcdc4 is unused and should be disabled. On A80 boards dcdc4 powers VDD-SYS, HDMI, USB OTG and should be 0.9V. On A83T boards dcdc4 is used for VDD-GPU.
config AXP_DCDC5_VOLT int "axp pmic dcdc5 voltage" - depends on AXP221_POWER || AXP809_POWER || AXP818_POWER - default 1500 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I + depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER + default 1500 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I || MACH_SUN50I ---help--- Set the voltage (mV) to program the axp pmic dcdc5 at, set to 0 to disable dcdc5. - On A23 / A31 / A33 / A80 / A83T boards dcdc5 is VCC-DRAM and + On A23 / A31 / A33 / A64 / A80 / A83T boards dcdc5 is VCC-DRAM and should be 1.5V, 1.35V if DDR3L is used.
config AXP_ALDO1_VOLT int "axp pmic (a)ldo1 voltage" - depends on AXP221_POWER || AXP809_POWER || AXP818_POWER + depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER default 0 if MACH_SUN6I default 1800 if MACH_SUN8I_A83T default 3000 if MACH_SUN8I || MACH_SUN9I + default 2800 if MACH_SUN50I ---help--- Set the voltage (mV) to program the axp pmic aldo1 at, set to 0 to disable aldo1. @@ -155,14 +168,16 @@ config AXP_ALDO1_VOLT On A80 boards aldo1 powers the USB hosts and should be 3.0V. On A83T / H8 boards aldo1 is used for MIPI CSI, DSI, HDMI, EFUSE, and should be 1.8V. + On A64 boards aldo1 powers PE pingroup and CSI and should be 2.8V.
config AXP_ALDO2_VOLT int "axp pmic (a)ldo2 voltage" - depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER + depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER default 3000 if AXP152_POWER || AXP209_POWER default 0 if MACH_SUN6I || MACH_SUN9I default 1800 if MACH_SUN8I_A83T default 2500 if MACH_SUN8I + default 1800 if MACH_SUN50I ---help--- Set the voltage (mV) to program the axp pmic aldo2 at, set to 0 to disable aldo2. @@ -173,17 +188,19 @@ config AXP_ALDO2_VOLT On A80 boards aldo2 powers PB pingroup and camera IO and can be left off. On A83T / H8 boards aldo2 powers VDD-DLL, VCC18-PLL, CPVDD, VDD18-ADC, LPDDR2, and the codec. It should be 1.8V. + On A64 boards aldo2 powers PL pingroup and should be 1.8V.
config AXP_ALDO3_VOLT int "axp pmic (a)ldo3 voltage" - depends on AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER + depends on AXP209_POWER || AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER default 0 if AXP209_POWER || MACH_SUN9I - default 3000 if MACH_SUN6I || MACH_SUN8I + default 3000 if MACH_SUN6I || MACH_SUN8I || MACH_SUN50I ---help--- Set the voltage (mV) to program the axp pmic aldo3 at, set to 0 to disable aldo3. On A10(s) / A13 / A20 boards aldo3 should be 2.8V. - On A23 / A31 / A33 boards aldo3 is VCC-PLL and AVCC and should be 3.0V. + On A23 / A31 / A33 / A64 boards aldo3 is VCC-PLL and AVCC + and should be 3.0V. On A80 boards aldo3 is normally not used. On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be 3.0V. @@ -199,17 +216,19 @@ config AXP_ALDO4_VOLT
config AXP_DLDO1_VOLT int "axp pmic dldo1 voltage" - depends on AXP221_POWER || AXP809_POWER || AXP818_POWER + depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER + default 3300 if MACH_SUN50I default 0 ---help--- Set the voltage (mV) to program the axp pmic dldo1 at, set to 0 to disable dldo1. On sun6i (A31) boards with ethernet dldo1 is often used to power the ethernet phy. On A23, A33 and A80 boards this is often - used to power the wifi. + used to power the wifi. On A64 boards this is often used to power the + HDMI.
config AXP_DLDO2_VOLT int "axp pmic dldo2 voltage" - depends on AXP221_POWER || AXP809_POWER || AXP818_POWER + depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER default 3000 if MACH_SUN9I default 0 ---help--- @@ -219,7 +238,7 @@ config AXP_DLDO2_VOLT
config AXP_DLDO3_VOLT int "axp pmic dldo3 voltage" - depends on AXP221_POWER || AXP818_POWER + depends on AXP221_POWER || AXP803_POWER || AXP818_POWER default 0 ---help--- Set the voltage (mV) to program the axp pmic dldo3 at, set to 0 to @@ -227,7 +246,7 @@ config AXP_DLDO3_VOLT
config AXP_DLDO4_VOLT int "axp pmic dldo4 voltage" - depends on AXP221_POWER || AXP818_POWER + depends on AXP221_POWER || AXP803_POWER || AXP818_POWER default 0 ---help--- Set the voltage (mV) to program the axp pmic dldo4 at, set to 0 to @@ -235,15 +254,17 @@ config AXP_DLDO4_VOLT
config AXP_ELDO1_VOLT int "axp pmic eldo1 voltage" - depends on AXP221_POWER || AXP809_POWER || AXP818_POWER + depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER + default 1800 if MACH_SUN50I default 0 ---help--- Set the voltage (mV) to program the axp pmic eldo1 at, set to 0 to disable eldo1. + On A64 boards it's used for the codec and should be 1.8V.
config AXP_ELDO2_VOLT int "axp pmic eldo2 voltage" - depends on AXP221_POWER || AXP809_POWER || AXP818_POWER + depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER default 0 ---help--- Set the voltage (mV) to program the axp pmic eldo2 at, set to 0 to @@ -251,7 +272,7 @@ config AXP_ELDO2_VOLT
config AXP_ELDO3_VOLT int "axp pmic eldo3 voltage" - depends on AXP221_POWER || AXP809_POWER || AXP818_POWER + depends on AXP221_POWER || AXP803_POWER || AXP809_POWER || AXP818_POWER default 3000 if MACH_SUN9I default 0 ---help--- @@ -263,8 +284,8 @@ config AXP_ELDO3_VOLT
config AXP_FLDO1_VOLT int "axp pmic fldo1 voltage" - depends on AXP818_POWER - default 0 if MACH_SUN8I_A83T + depends on AXP803_POWER || AXP818_POWER + default 0 ---help--- Set the voltage (mV) to program the axp pmic fldo1 at, set to 0 to disable fldo1. @@ -273,11 +294,13 @@ config AXP_FLDO1_VOLT
config AXP_FLDO2_VOLT int "axp pmic fldo2 voltage" - depends on AXP818_POWER + depends on AXP803_POWER || AXP818_POWER + default 1100 if MACH_SUN50I default 900 if MACH_SUN8I_A83T ---help--- Set the voltage (mV) to program the axp pmic fldo2 at, set to 0 to disable fldo2. + On A64 boards fldo2 is VCC-CPUS and should be 1.1V. On A83T / H8 boards fldo2 is VCC-CPUS and should be 0.9V.
config AXP_FLDO3_VOLT @@ -290,7 +313,7 @@ config AXP_FLDO3_VOLT
config AXP_SW_ON bool "axp pmic sw on" - depends on AXP809_POWER || AXP818_POWER + depends on AXP803_POWER || AXP809_POWER || AXP818_POWER default n ---help--- Enable to turn on axp pmic sw. diff --git a/drivers/power/Makefile b/drivers/power/Makefile index b43523e628..1449e875ce 100644 --- a/drivers/power/Makefile +++ b/drivers/power/Makefile @@ -9,6 +9,7 @@ obj-$(CONFIG_AS3722_POWER) += as3722.o obj-$(CONFIG_AXP152_POWER) += axp152.o obj-$(CONFIG_AXP209_POWER) += axp209.o obj-$(CONFIG_AXP221_POWER) += axp221.o +obj-$(CONFIG_AXP803_POWER) += axp803.o obj-$(CONFIG_AXP809_POWER) += axp809.o obj-$(CONFIG_AXP818_POWER) += axp818.o obj-$(CONFIG_EXYNOS_TMU) += exynos-tmu.o diff --git a/drivers/power/axp803.c b/drivers/power/axp803.c new file mode 100644 index 0000000000..93b9d95234 --- /dev/null +++ b/drivers/power/axp803.c @@ -0,0 +1,256 @@ +/* + * AXP803 driver based on AXP818 driver + * + * Based on axp818.c + * (C) Copyright 2015 Vishnu Patekar vishnuptekar0510@gmail.com + * + * Based on axp221.c + * (C) Copyright 2014 Hans de Goede hdegoede@redhat.com + * (C) Copyright 2013 Oliver Schinagl oliver@schinagl.nl + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <errno.h> +#include <asm/arch/gpio.h> +#include <asm/arch/pmic_bus.h> +#include <axp_pmic.h> + +static u8 axp803_mvolt_to_cfg(int mvolt, int min, int max, int div) +{ + if (mvolt < min) + mvolt = min; + else if (mvolt > max) + mvolt = max; + + return (mvolt - min) / div; +} + +int axp_set_dcdc1(unsigned int mvolt) +{ + int ret; + u8 cfg = axp803_mvolt_to_cfg(mvolt, 1600, 3400, 100); + + if (mvolt == 0) + return pmic_bus_clrbits(AXP803_OUTPUT_CTRL1, + AXP803_OUTPUT_CTRL1_DCDC1_EN); + + ret = pmic_bus_write(AXP803_DCDC1_CTRL, cfg); + if (ret) + return ret; + + return pmic_bus_setbits(AXP803_OUTPUT_CTRL1, + AXP803_OUTPUT_CTRL1_DCDC1_EN); +} + +int axp_set_dcdc2(unsigned int mvolt) +{ + int ret; + u8 cfg; + + if (mvolt >= 1220) + cfg = 70 + axp803_mvolt_to_cfg(mvolt, 1220, 1300, 20); + else + cfg = axp803_mvolt_to_cfg(mvolt, 500, 1200, 10); + + if (mvolt == 0) + return pmic_bus_clrbits(AXP803_OUTPUT_CTRL1, + AXP803_OUTPUT_CTRL1_DCDC2_EN); + + ret = pmic_bus_write(AXP803_DCDC2_CTRL, cfg); + if (ret) + return ret; + + return pmic_bus_setbits(AXP803_OUTPUT_CTRL1, + AXP803_OUTPUT_CTRL1_DCDC2_EN); +} + +int axp_set_dcdc3(unsigned int mvolt) +{ + int ret; + u8 cfg; + + if (mvolt >= 1220) + cfg = 70 + axp803_mvolt_to_cfg(mvolt, 1220, 1300, 20); + else + cfg = axp803_mvolt_to_cfg(mvolt, 500, 1200, 10); + + if (mvolt == 0) + return pmic_bus_clrbits(AXP803_OUTPUT_CTRL1, + AXP803_OUTPUT_CTRL1_DCDC3_EN); + + ret = pmic_bus_write(AXP803_DCDC3_CTRL, cfg); + if (ret) + return ret; + + return pmic_bus_setbits(AXP803_OUTPUT_CTRL1, + AXP803_OUTPUT_CTRL1_DCDC3_EN); +} + +int axp_set_dcdc5(unsigned int mvolt) +{ + int ret; + u8 cfg; + + if (mvolt >= 1140) + cfg = 32 + axp803_mvolt_to_cfg(mvolt, 1140, 1840, 20); + else + cfg = axp803_mvolt_to_cfg(mvolt, 800, 1120, 10); + + if (mvolt == 0) + return pmic_bus_clrbits(AXP803_OUTPUT_CTRL1, + AXP803_OUTPUT_CTRL1_DCDC5_EN); + + ret = pmic_bus_write(AXP803_DCDC5_CTRL, cfg); + if (ret) + return ret; + + return pmic_bus_setbits(AXP803_OUTPUT_CTRL1, + AXP803_OUTPUT_CTRL1_DCDC5_EN); +} + +int axp_set_aldo(int aldo_num, unsigned int mvolt) +{ + int ret; + u8 cfg; + + if (aldo_num < 1 || aldo_num > 3) + return -EINVAL; + + if (mvolt == 0) + return pmic_bus_clrbits(AXP803_OUTPUT_CTRL3, + AXP803_OUTPUT_CTRL3_ALDO1_EN << (aldo_num - 1)); + + cfg = axp803_mvolt_to_cfg(mvolt, 700, 3300, 100); + ret = pmic_bus_write(AXP803_ALDO1_CTRL + (aldo_num - 1), cfg); + if (ret) + return ret; + + return pmic_bus_setbits(AXP803_OUTPUT_CTRL3, + AXP803_OUTPUT_CTRL3_ALDO1_EN << (aldo_num - 1)); +} + +/* TODO: re-work other AXP drivers to consolidate ALDO functions. */ +int axp_set_aldo1(unsigned int mvolt) +{ + return axp_set_aldo(1, mvolt); +} + +int axp_set_aldo2(unsigned int mvolt) +{ + return axp_set_aldo(2, mvolt); +} + +int axp_set_aldo3(unsigned int mvolt) +{ + return axp_set_aldo(3, mvolt); +} + +int axp_set_dldo(int dldo_num, unsigned int mvolt) +{ + int ret; + u8 cfg; + + if (dldo_num < 1 || dldo_num > 4) + return -EINVAL; + + if (mvolt == 0) + return pmic_bus_clrbits(AXP803_OUTPUT_CTRL2, + AXP803_OUTPUT_CTRL2_DLDO1_EN << (dldo_num - 1)); + + cfg = axp803_mvolt_to_cfg(mvolt, 700, 3300, 100); + if (dldo_num == 2 && mvolt > 3300) + cfg += 1 + axp803_mvolt_to_cfg(mvolt, 3400, 4200, 200); + ret = pmic_bus_write(AXP803_DLDO1_CTRL + (dldo_num - 1), cfg); + if (ret) + return ret; + + return pmic_bus_setbits(AXP803_OUTPUT_CTRL2, + AXP803_OUTPUT_CTRL2_DLDO1_EN << (dldo_num - 1)); +} + +int axp_set_eldo(int eldo_num, unsigned int mvolt) +{ + int ret; + u8 cfg; + + if (eldo_num < 1 || eldo_num > 3) + return -EINVAL; + + if (mvolt == 0) + return pmic_bus_clrbits(AXP803_OUTPUT_CTRL2, + AXP803_OUTPUT_CTRL2_ELDO1_EN << (eldo_num - 1)); + + cfg = axp803_mvolt_to_cfg(mvolt, 700, 1900, 50); + ret = pmic_bus_write(AXP803_ELDO1_CTRL + (eldo_num - 1), cfg); + if (ret) + return ret; + + return pmic_bus_setbits(AXP803_OUTPUT_CTRL2, + AXP803_OUTPUT_CTRL2_ELDO1_EN << (eldo_num - 1)); +} + +int axp_set_fldo(int fldo_num, unsigned int mvolt) +{ + int ret; + u8 cfg; + + if (fldo_num < 1 || fldo_num > 2) + return -EINVAL; + + if (mvolt == 0) + return pmic_bus_clrbits(AXP803_OUTPUT_CTRL3, + AXP803_OUTPUT_CTRL3_FLDO1_EN << (fldo_num - 1)); + + cfg = axp803_mvolt_to_cfg(mvolt, 700, 1450, 50); + ret = pmic_bus_write(AXP803_FLDO1_CTRL + (fldo_num - 1), cfg); + if (ret) + return ret; + + return pmic_bus_setbits(AXP803_OUTPUT_CTRL3, + AXP803_OUTPUT_CTRL3_FLDO1_EN << (fldo_num - 1)); +} + +int axp_set_sw(bool on) +{ + if (on) + return pmic_bus_setbits(AXP803_OUTPUT_CTRL2, + AXP803_OUTPUT_CTRL2_SW_EN); + + return pmic_bus_clrbits(AXP803_OUTPUT_CTRL2, + AXP803_OUTPUT_CTRL2_SW_EN); +} + +int axp_init(void) +{ + u8 axp_chip_id; + int ret; + + ret = pmic_bus_init(); + if (ret) + return ret; + + ret = pmic_bus_read(AXP803_CHIP_ID, &axp_chip_id); + if (ret) + return ret; + + if (!(axp_chip_id == 0x51)) + return -ENODEV; + else + return ret; + + return 0; +} + +int do_poweroff(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + pmic_bus_write(AXP803_SHUTDOWN, AXP803_SHUTDOWN_POWEROFF); + + /* infinite loop during shutdown */ + while (1) + ; + + /* not reached */ + return 0; +} diff --git a/drivers/power/axp818.c b/drivers/power/axp818.c index af4d7a6903..ad0c330ca5 100644 --- a/drivers/power/axp818.c +++ b/drivers/power/axp818.c @@ -162,7 +162,7 @@ int axp_set_dldo(int dldo_num, unsigned int mvolt) cfg = axp818_mvolt_to_cfg(mvolt, 700, 3300, 100); if (dldo_num == 2 && mvolt > 3300) cfg += 1 + axp818_mvolt_to_cfg(mvolt, 3400, 4200, 200); - ret = pmic_bus_write(AXP818_ELDO1_CTRL + (dldo_num - 1), cfg); + ret = pmic_bus_write(AXP818_DLDO1_CTRL + (dldo_num - 1), cfg); if (ret) return ret;
diff --git a/include/axp803.h b/include/axp803.h new file mode 100644 index 0000000000..b382f3a5ec --- /dev/null +++ b/include/axp803.h @@ -0,0 +1,73 @@ +/* + * (C) Copyright 2016 Icenowy Zheng icenowy@aosc.xyz + * + * Based on axp818.h, which is: + * (C) Copyright 2015 Vishnu Patekar vishnupatekar0510@gmail.com + * + * X-Powers AXP803 Power Management IC driver + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#define AXP803_CHIP_ID 0x03 + +#define AXP803_OUTPUT_CTRL1 0x10 +#define AXP803_OUTPUT_CTRL1_DCDC1_EN (1 << 0) +#define AXP803_OUTPUT_CTRL1_DCDC2_EN (1 << 1) +#define AXP803_OUTPUT_CTRL1_DCDC3_EN (1 << 2) +#define AXP803_OUTPUT_CTRL1_DCDC4_EN (1 << 3) +#define AXP803_OUTPUT_CTRL1_DCDC5_EN (1 << 4) +#define AXP803_OUTPUT_CTRL1_DCDC6_EN (1 << 5) +#define AXP803_OUTPUT_CTRL2 0x12 +#define AXP803_OUTPUT_CTRL2_ELDO1_EN (1 << 0) +#define AXP803_OUTPUT_CTRL2_ELDO2_EN (1 << 1) +#define AXP803_OUTPUT_CTRL2_ELDO3_EN (1 << 2) +#define AXP803_OUTPUT_CTRL2_DLDO1_EN (1 << 3) +#define AXP803_OUTPUT_CTRL2_DLDO2_EN (1 << 4) +#define AXP803_OUTPUT_CTRL2_DLDO3_EN (1 << 5) +#define AXP803_OUTPUT_CTRL2_DLDO4_EN (1 << 6) +#define AXP803_OUTPUT_CTRL2_SW_EN (1 << 7) +#define AXP803_OUTPUT_CTRL3 0x13 +#define AXP803_OUTPUT_CTRL3_FLDO1_EN (1 << 2) +#define AXP803_OUTPUT_CTRL3_FLDO2_EN (1 << 3) +#define AXP803_OUTPUT_CTRL3_ALDO1_EN (1 << 5) +#define AXP803_OUTPUT_CTRL3_ALDO2_EN (1 << 6) +#define AXP803_OUTPUT_CTRL3_ALDO3_EN (1 << 7) + +#define AXP803_DLDO1_CTRL 0x15 +#define AXP803_DLDO2_CTRL 0x16 +#define AXP803_DLDO3_CTRL 0x17 +#define AXP803_DLDO4_CTRL 0x18 +#define AXP803_ELDO1_CTRL 0x19 +#define AXP803_ELDO2_CTRL 0x1a +#define AXP803_ELDO3_CTRL 0x1b +#define AXP803_FLDO1_CTRL 0x1c +#define AXP803_FLDO2_CTRL 0x1d +#define AXP803_DCDC1_CTRL 0x20 +#define AXP803_DCDC2_CTRL 0x21 +#define AXP803_DCDC3_CTRL 0x22 +#define AXP803_DCDC4_CTRL 0x23 +#define AXP803_DCDC5_CTRL 0x24 +#define AXP803_DCDC6_CTRL 0x25 + +#define AXP803_ALDO1_CTRL 0x28 +#define AXP803_ALDO2_CTRL 0x29 +#define AXP803_ALDO3_CTRL 0x2a + +#define AXP803_SHUTDOWN 0x32 +#define AXP803_SHUTDOWN_POWEROFF (1 << 7) + +/* For axp_gpio.c */ +#define AXP_POWER_STATUS 0x00 +#define AXP_POWER_STATUS_VBUS_PRESENT (1 << 5) +#define AXP_VBUS_IPSOUT 0x30 +#define AXP_VBUS_IPSOUT_DRIVEBUS (1 << 2) +#define AXP_MISC_CTRL 0x8f +#define AXP_MISC_CTRL_N_VBUSEN_FUNC (1 << 4) +#define AXP_GPIO0_CTRL 0x90 +#define AXP_GPIO1_CTRL 0x92 +#define AXP_GPIO_CTRL_OUTPUT_LOW 0x00 /* Drive pin low */ +#define AXP_GPIO_CTRL_OUTPUT_HIGH 0x01 /* Drive pin high */ +#define AXP_GPIO_CTRL_INPUT 0x02 /* Input */ +#define AXP_GPIO_STATE 0x94 +#define AXP_GPIO_STATE_OFFSET 0 diff --git a/include/axp_pmic.h b/include/axp_pmic.h index d789ad8086..8cb4d5763c 100644 --- a/include/axp_pmic.h +++ b/include/axp_pmic.h @@ -16,6 +16,9 @@ #ifdef CONFIG_AXP221_POWER #include <axp221.h> #endif +#ifdef CONFIG_AXP803_POWER +#include <axp803.h> +#endif #ifdef CONFIG_AXP809_POWER #include <axp809.h> #endif