I built u-boot with the additional parameter for usb and it works, I think. There was one message that might be of concern " Card did not respond to voltage select! : -110". I am not sure of the details of the boot.cmd. The output below came from the supplier image on an SD plugged into a USB card reader. The SD slot of the board was empty.
I was able to install u-boot to the SPI flash memory and there is a warning message from that also: " Loading Environment from SPIFlash... jedec_spi_nor flash@0: unrecognized JEDEC id bytes: 5e, 40, 18 *** Warning - spi_flash_probe_bus_cs() failed, using default environment"
Thank you for your advice on getting something to boot. None of the Debian installer images were suitable. Even SID was at 6.1. I built the latest Linux 6.6.2 and wrestled with the rootfs before I got it running. I built the tested u-boot with this system, as a test of system stability.
defconfig used + emac patches
CONFIG_ARM=y CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-h618-orangepi-zero3" CONFIG_SPL=y CONFIG_DRAM_SUN50I_H616_DX_ODT=0x07070707 CONFIG_DRAM_SUN50I_H616_DX_DRI=0x0e0e0e0e CONFIG_DRAM_SUN50I_H616_CA_DRI=0x0e0e CONFIG_DRAM_SUN50I_H616_ODT_EN=0xaaaaeeee CONFIG_DRAM_SUN50I_H616_TPR6=0x44000000 CONFIG_DRAM_SUN50I_H616_TPR10=0x402f6663 CONFIG_DRAM_SUN50I_H616_TPR11=0x24242624 CONFIG_DRAM_SUN50I_H616_TPR12=0x0f0f100f CONFIG_MACH_SUN50I_H616=y CONFIG_SUNXI_DRAM_H616_LPDDR4=y # CONFIG_DRAM_CLK=792 CONFIG_USB1_VBUS_PIN="PC16" # CONFIG_R_I2C_ENABLE=y CONFIG_SPL_SPI_SUNXI=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_I2C=y CONFIG_SPL_SYS_I2C_LEGACY=y CONFIG_SYS_I2C_MVTWSI=y CONFIG_SYS_I2C_SLAVE=0x7f CONFIG_SYS_I2C_SPEED=400000 CONFIG_SPI_FLASH_ZBIT=y CONFIG_PHY_MOTORCOMM=y CONFIG_SUN8I_EMAC=y CONFIG_AXP313_POWER=y CONFIG_SPI=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_OHCI_HCD=y CONFIG_USB_MUSB_GADGET=y
Console Output:
U-Boot 2024.01-rc3-00009-g9e53e45292-dirty (Nov 25 2023 - 18:32:16 -0800) Allwinner Technology
CPU: Allwinner H616 (SUN50I) Model: OrangePi Zero3 DRAM: 1 GiB Core: 57 devices, 25 uclasses, devicetree: separate WDT: Not starting watchdog@30090a0 MMC: mmc@4020000: 0 Loading Environment from SPIFlash... jedec_spi_nor flash@0: unrecognized JEDEC id bytes: 5e, 40, 18 *** Warning - spi_flash_probe_bus_cs() failed, using default environment
Loading Environment from FAT... Card did not respond to voltage select! : -110 ** Bad device specification mmc 0 ** In: serial@5000000 Out: serial@5000000 Err: serial@5000000 Allwinner mUSB OTG (Peripheral) Net: eth0: ethernet@5020000using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in MAC de:ad:be:ef:00:01 HOST MAC de:ad:be:ef:00:00 RNDIS ready , eth1: usb_ether starting USB... Bus usb@5200000: USB EHCI 1.00 Bus usb@5200400: USB OHCI 1.0 scanning bus usb@5200000 for devices... Device NOT ready Request Sense returned 02 3A 00 Device NOT ready Request Sense returned 02 3A 00 Device NOT ready Request Sense returned 02 3A 00 2 USB Device(s) found scanning bus usb@5200400 for devices... 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Hit any key to stop autoboot: 0 Card did not respond to voltage select! : -110
Device 0: Vendor: Generic- Rev: 1.00 Prod: SD/MMC Type: Removable Hard Disk Capacity: 15193.5 MB = 14.8 GB (31116288 x 512) ... is now current device Scanning usb 0:1... Found U-Boot script /boot/boot.scr 3636 bytes read in 1 ms (3.5 MiB/s) ## Executing script at 4fc00000 U-boot loaded from SD Boot script loaded from usb 205 bytes read in 1 ms (200.2 KiB/s) Failed to load '/boot/dtb/allwinner/sun50i-h618-orangepi-zero3.dtb' libfdt fdt_check_header(): FDT_ERR_BADMAGIC No FDT memory address configured. Please configure the FDT address via "fdt addr <address>" command. Aborting! 4203 bytes read in 4 ms (1 MiB/s) Applying kernel provided DT fixup script (sun50i-h616-fixup.scr) ## Executing script at 45000000 7088139 bytes read in 325 ms (20.8 MiB/s) 9419107 bytes read in 430 ms (20.9 MiB/s) Uncompressing Kernel Image Moving Image from 0x40080000 to 0x40200000, end=41800000 ## Loading init Ramdisk from Legacy Image at 4ff00000 ... Image Name: uInitrd Image Type: AArch64 Linux RAMDisk Image (gzip compressed) Data Size: 7088075 Bytes = 6.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ERROR: Did not find a cmdline Flattened Device Tree
On 2023-11-25 4:23 p.m., Andre Przywara wrote:
On Sat, 25 Nov 2023 20:43:12 +0300 Mikhail Kalashnikoviuncuim@gmail.com wrote:
Hi Mikhail,
Hi Andre! Thanks for your patches. I started checking and noticed that USB storage was not working:
=> usb reset resetting USB... Bus usb@5200000: USB EHCI 1.00 Bus usb@5200400: USB OHCI 1.0 scanning bus usb@5200000 for devices... 1 USB Device(s) found scanning bus usb@5200400 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found => usb storage No storage devices, perhaps not 'usb start'ed..?
Ah, thanks for the report, seems I didn't even test this! So digging around I figured it's working in Linux, and it's the right USB port, but we are missing the VBUS power switch, which is a GPIO controlled regulator. There are pending patches to pick this from the devicetree[1], but we are not there yet, so we need: CONFIG_USB1_VBUS_PIN="PC16" in the defconfig, for now. I will update the file. The same is actually missing from the OrangePi Zero2 defconfig, I will send a patch ASAP.
Otherwise my OpiZero3 (4GB) board looks working. Ethernet works with my 10 Mbps usb-dongle.
sf probe detect spi nor flash: => sf probe SF: Detected zb25vq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
Loading the kernel and running the operating system (from microsd) also without problems.
Tested-by: Mikhail Kalashnikoviuncuim@gmail.com
Great, thanks for the tag!
Cheers, Andre
On 14.11.2023 04:31, Andre Przywara wrote:
The OrangePi Zero 3 is a small development board featuring the Allwinner H618 SoC, shipping with up to 4GB of DRAM, Gigabit Ethernet, a micro-HDMI connector and two USB sockets. The board uses LPDDR4 DRAM and an X-Powers AXP313a PMIC, support for which was recently added to U-Boot.
Add a defconfig file selecting the right drivers and DRAM options. Since the .dts file was synced from the Linux kernel repo already, we just need to add one line to the Makefile to actually build the .dtb.
The DRAM parameters were derived from the values found in the BSP DRAM drivers on the SPI NOR flash.
Signed-off-by: Andre Przywaraandre.przywara@arm.com
arch/arm/dts/Makefile | 1 + board/sunxi/MAINTAINERS | 5 +++++ configs/orangepi_zero3_defconfig | 30 ++++++++++++++++++++++++++++++ 3 files changed, 36 insertions(+) create mode 100644 configs/orangepi_zero3_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 1be08c5fdc2..5fc888680b3 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -835,6 +835,7 @@ dtb-$(CONFIG_MACH_SUN50I_H6) += \ sun50i-h6-tanix-tx6-mini.dtb dtb-$(CONFIG_MACH_SUN50I_H616) += \ sun50i-h616-orangepi-zero2.dtb \
- sun50i-h618-orangepi-zero3.dtb \ sun50i-h616-x96-mate.dtb dtb-$(CONFIG_MACH_SUN50I) += \ sun50i-a64-amarula-relic.dtb \
diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS index 00614372119..f556857a391 100644 --- a/board/sunxi/MAINTAINERS +++ b/board/sunxi/MAINTAINERS @@ -455,6 +455,11 @@ M: Jernej Skrabecjernej.skrabec@siol.net S: Maintained F: configs/orangepi_zero2_defconfig
+ORANGEPI ZERO 3 BOARD +M: Andre Przywaraandre.przywara@arm.com +S: Maintained +F: configs/orangepi_zero3_defconfig
- ORANGEPI PC 2 BOARD M: Andre Przywaraandre.przywara@arm.com S: Maintained
diff --git a/configs/orangepi_zero3_defconfig b/configs/orangepi_zero3_defconfig new file mode 100644 index 00000000000..e59044f6639 --- /dev/null +++ b/configs/orangepi_zero3_defconfig @@ -0,0 +1,30 @@ +CONFIG_ARM=y +CONFIG_ARCH_SUNXI=y +CONFIG_DEFAULT_DEVICE_TREE="sun50i-h618-orangepi-zero3" +CONFIG_SPL=y +CONFIG_DRAM_SUN50I_H616_DX_ODT=0x07070707 +CONFIG_DRAM_SUN50I_H616_DX_DRI=0x0e0e0e0e +CONFIG_DRAM_SUN50I_H616_CA_DRI=0x0e0e +CONFIG_DRAM_SUN50I_H616_ODT_EN=0xaaaaeeee +CONFIG_DRAM_SUN50I_H616_TPR6=0x44000000 +CONFIG_DRAM_SUN50I_H616_TPR10=0x402f6663 +CONFIG_DRAM_SUN50I_H616_TPR11=0x24242624 +CONFIG_DRAM_SUN50I_H616_TPR12=0x0f0f100f +CONFIG_MACH_SUN50I_H616=y +CONFIG_SUNXI_DRAM_H616_LPDDR4=y +CONFIG_R_I2C_ENABLE=y +CONFIG_SPL_SPI_SUNXI=y +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +CONFIG_SPL_I2C=y +CONFIG_SPL_SYS_I2C_LEGACY=y +CONFIG_SYS_I2C_MVTWSI=y +CONFIG_SYS_I2C_SLAVE=0x7f +CONFIG_SYS_I2C_SPEED=400000 +CONFIG_SPI_FLASH_ZBIT=y +CONFIG_PHY_MOTORCOMM=y +CONFIG_SUN8I_EMAC=y +CONFIG_AXP313_POWER=y +CONFIG_SPI=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_MUSB_GADGET=y