Hi Lokesh,
On Tue, May 9, 2017 at 10:03 PM, Jagan Teki jagannadh.teki@gmail.com wrote:
On Tue, May 9, 2017 at 8:54 PM, Lokesh Vutla lokeshvutla@ti.com wrote:
On Tuesday 09 May 2017 08:37 PM, Jagan Teki wrote:
On Tue, May 9, 2017 at 7:49 PM, Lokesh Vutla lokeshvutla@ti.com wrote:
On Tuesday 09 May 2017 04:35 PM, Jagan Teki wrote:
Hi All,
I'm trying to add SPL_OF_CONTROL for i.MX6UL, with usdhc1 and gpio1 nodes are marking as "u-boot,dm-pre-reloc" like
Did you try "u-boot,dm-spl" instead?
Yes, no change.
Hmm..Ideally this should have taken effect :(
--- a/arch/arm/dts/imx6ul.dtsi +++ b/arch/arm/dts/imx6ul.dtsi @@ -129,6 +129,7 @@ };
soc {
u-boot,dm-pre-reloc; #address-cells = <1>; #size-cells = <1>; compatible = "simple-bus";@@ -180,6 +181,7 @@ };
aips1: aips-bus@02000000 {
u-boot,dm-pre-reloc; compatible = "fsl,aips-bus", "simple-bus"; #address-cells = <1>; #size-cells = <1>;@@ -405,6 +407,7 @@ };
gpio1: gpio@0209c000 {
u-boot,dm-pre-reloc; compatible = "fsl,imx6ul-gpio","fsl,imx35-gpio"; reg = <0x0209c000 0x4000>; interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>, @@ -724,6 +727,7 @@ };
aips2: aips-bus@02100000 {
u-boot,dm-pre-reloc; compatible = "fsl,aips-bus", "simple-bus"; #address-cells = <1>; #size-cells = <1>;@@ -781,6 +785,7 @@ };
usdhc1: usdhc@02190000 {
u-boot,dm-pre-reloc; compatible = "fsl,imx6ul-usdhc","fsl,imx6sx-usdhc"; reg = <0x02190000 0x4000>; interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
SPL is loading fine from MMC but block the U-Boot that means we can't see U-Boot log on console.
Any chance you can try enabling early debug? Since enabling pre-reloc is going for a toss, I guess your malloc size is going for a toss. Can you try increasing initial malloc size?
Yes, I've increased malloc CONFIG_SYS_MALLOC_LEN from 16M to upto 128M but no change.
No, try CONFIG_SYS_MALLOC_F_LEN=0x2000.
Is it possible to check where exactly is it hanged?
Yes, it hangs while relocating dram[1] and I also observed the main bus nodes are are 'not found' which I haven't see before and these are marked 'u-boot,dm-spl'
uclass_find_device_by_seq: 0 -1 uclass_find_device_by_seq: 0 0
- -1 -1 'soc'
- -1 -1 'aips-bus@02000000'
- -1 -1 'aips-bus@02100000'
- not found
Any clue, I still investigating. Look like the node seq numbers which are marked as "u-boot,dm-spl" in SPL are checking before relocating in U-Boot, and they seems not found.
Interestingly I couldn't see any panic or exception, the code ends board_f last line.
thanks!