J721e has two instances of Cadence USB3 controller. Add DT nodes for the same. USB0 is configured to device mode and USB1 is configured to host mode. For now only high speed mode is supported.
Signed-off-by: Vignesh Raghavendra vigneshr@ti.com --- .../k3-j721e-common-proc-board-u-boot.dtsi | 14 ++++ arch/arm/dts/k3-j721e-common-proc-board.dts | 37 ++++++++++ arch/arm/dts/k3-j721e-main.dtsi | 70 +++++++++++++++++++ .../arm/dts/k3-j721e-r5-common-proc-board.dts | 7 ++ 4 files changed, 128 insertions(+)
diff --git a/arch/arm/dts/k3-j721e-common-proc-board-u-boot.dtsi b/arch/arm/dts/k3-j721e-common-proc-board-u-boot.dtsi index c4f2dd6b4fb2..c66e029b88ad 100644 --- a/arch/arm/dts/k3-j721e-common-proc-board-u-boot.dtsi +++ b/arch/arm/dts/k3-j721e-common-proc-board-u-boot.dtsi @@ -311,6 +311,20 @@ u-boot,dm-spl; };
+&main_usbss0_pins_default { + u-boot,dm-spl; +}; + +&usbss0 { + u-boot,dm-spl; + ti,usb2-only; +}; + +&usb0 { + dr_mode = "peripheral"; + u-boot,dm-spl; +}; + &mcu_cpsw { pinctrl-names = "default"; pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>; diff --git a/arch/arm/dts/k3-j721e-common-proc-board.dts b/arch/arm/dts/k3-j721e-common-proc-board.dts index c978cabd1335..137da7e425a1 100644 --- a/arch/arm/dts/k3-j721e-common-proc-board.dts +++ b/arch/arm/dts/k3-j721e-common-proc-board.dts @@ -77,3 +77,40 @@ voltage-ranges = <1800 1800 3300 3300>; ti,driver-strength-ohm = <50>; }; + +&main_pmx0 { + main_usbss0_pins_default: main_usbss0_pins_default { + pinctrl-single,pins = < + J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */ + J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */ + >; + }; + + main_usbss1_pins_default: main_usbss1_pins_default { + pinctrl-single,pins = < + J721E_IOPAD(0x214, PIN_OUTPUT, 4) /* (V4) MCAN1_TX.USB1_DRVVBUS */ + >; + }; +}; + +&usbss0 { + pinctrl-names = "default"; + pinctrl-0 = <&main_usbss0_pins_default>; + ti,vbus-divider; +}; + +&usb0 { + dr_mode = "otg"; + maximum-speed = "super-speed"; +}; + +&usbss1 { + pinctrl-names = "default"; + pinctrl-0 = <&main_usbss1_pins_default>; + ti,usb2-only; +}; + +&usb1 { + dr_mode = "host"; + maximum-speed = "high-speed"; +}; diff --git a/arch/arm/dts/k3-j721e-main.dtsi b/arch/arm/dts/k3-j721e-main.dtsi index 3a0763209fc2..5083a0c3aef0 100644 --- a/arch/arm/dts/k3-j721e-main.dtsi +++ b/arch/arm/dts/k3-j721e-main.dtsi @@ -340,6 +340,76 @@ resets = <&k3_reset 15 1>; };
+ usbss0: cdns_usb@4104000 { + compatible = "ti,j721e-usb"; + reg = <0x00 0x4104000 0x00 0x100>; + dma-coherent; + power-domains = <&k3_pds 288 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 288 15>, <&k3_clks 288 3>; + clock-names = "usb2_refclk", "lpm_clk"; + assigned-clocks = <&k3_clks 288 15>; /* USB2_REFCLK */ + assigned-clock-parents = <&k3_clks 288 16>; /* HFOSC0 */ + #address-cells = <2>; + #size-cells = <2>; + ranges; + + phy@4108000 { + compatible = "ti,j721e-usb2-phy"; + reg = <0x00 0x4108000 0x00 0x400>; + }; + + usb0: usb@6000000 { + compatible = "cdns,usb3"; + reg = <0x00 0x6000000 0x00 0x10000>, + <0x00 0x6010000 0x00 0x10000>, + <0x00 0x6020000 0x00 0x10000>; + reg-names = "otg", "xhci", "dev"; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */ + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, /* irq.6 */ + <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; /* otgirq.0 */ + interrupt-names = "host", + "peripheral", + "otg"; + maximum-speed = "super-speed"; + dr_mode = "otg"; + }; + }; + + usbss1: cdns_usb@4114000 { + compatible = "ti,j721e-usb"; + reg = <0x00 0x4114000 0x00 0x100>; + dma-coherent; + power-domains = <&k3_pds 289 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 289 15>, <&k3_clks 289 3>; + clock-names = "usb2_refclk", "lpm_clk"; + assigned-clocks = <&k3_clks 289 15>; /* USB2_REFCLK */ + assigned-clock-parents = <&k3_clks 289 16>; /* HFOSC0 */ + #address-cells = <2>; + #size-cells = <2>; + ranges; + + phy@4118000 { + compatible = "ti,j721e-usb2-phy"; + reg = <0x00 0x4118000 0x00 0x400>; + }; + + usb1: usb@6400000 { + compatible = "cdns,usb3"; + reg = <0x00 0x6400000 0x00 0x10000>, + <0x00 0x6410000 0x00 0x10000>, + <0x00 0x6420000 0x00 0x10000>; + reg-names = "otg", "xhci", "dev"; + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */ + <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>, /* irq.6 */ + <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; /* otgirq.0 */ + interrupt-names = "host", + "peripheral", + "otg"; + maximum-speed = "super-speed"; + dr_mode = "otg"; + }; + }; + ufs_wrapper: ufs-wrapper@4e80000 { compatible = "ti,j721e-ufs"; reg = <0x0 0x4e80000 0x0 0x100>; diff --git a/arch/arm/dts/k3-j721e-r5-common-proc-board.dts b/arch/arm/dts/k3-j721e-r5-common-proc-board.dts index 41af48214f6f..1a8e10786110 100644 --- a/arch/arm/dts/k3-j721e-r5-common-proc-board.dts +++ b/arch/arm/dts/k3-j721e-r5-common-proc-board.dts @@ -112,6 +112,13 @@ J721E_IOPAD(0x1ec, PIN_OUTPUT, 0) /* (AB3) UART0_TXD */ >; }; + + main_usbss0_pins_default: main_usbss0_pins_default { + pinctrl-single,pins = < + J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */ + J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */ + >; + }; };
&wkup_uart0 {