Hi, I am using uboot-toradex in my iris carrier with colibri t30
module.In
that when i am booting from sd card it is showing following error,
Hi, i cannot read your message at all ... where the linebreaks are gone?
best regards, Hannes
U-Boot 2011.06-00004-gccd521c (Mar 17 2014 - 09:48:16) TEGRA3 DRAM: 1 GiB MMC: Tegra2 SD/MMC: 0, Tegra2 SD/MMC: 1mmc_reset: power control = 0F,
host
control = 00Board: Toradex Colibri T30Net: Net Initialization
SkippedNo
ethernet found.Hit any key to stop autoboot: 0 Colibri T30 # run sdbootLoading kernel and rootfs from MMC/SD Card...mmc_reset: power
control =
0F, host control = 00mmc1 is current deviceGUID Partition Table Header signature is wrong:0xE1A0000DEA000002 != 0x5452415020494645get_partition_info_efi: *** ERROR: Invalid Primary GPT
***Loading file "/boot/uImage" from mmc device 1:1 (gpt1)GUID Partition
Table
Header signature is wrong:0xE1A0000DEA000002 != 0x5452415020494645get_partition_info_efi: *** ERROR: Invalid Primary GPT
***4324368 bytes read## Booting kernel from Legacy Image at 80408000 ...
Image Name: Linux-3.1.10 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4324304 Bytes = 4.1 MiB Load Address: 80008000 Entry Point: 80008000 Loading Kernel Image ... OKOK what
was
the problem? please help me. In my board environment variables are following, Colibri T30 # prbaudrate=115200bootcmd=run emmcboot; run usbboot; run nfsbootbootdelay=3defargs=core_edp_mv=1300 usb_high_speed=1emmcboot=run
setup;
setenv bootargs ${defargs} ${mmcargs} ${setupargs} ${vidargs}; echo
Booting
from internal eMMC chip...; mmc read ${loadaddr}
${lnxmethaddr=00:14:2d:26:0b:
9bfdtaddr=8014d538gptoffset=0xa001ipaddr=192.168.10. 2lnxoffset=0x5000loadaddr=0x80408000memargs=vmalloc=128M mem=1012M@2048M
fbmem=12M@3060Mmmc_kernel_size=0x4000mmcargs=ip=off root=/dev/mmcblk0p1 rw,noatime rootfstype=ext3 rootwaitnetmask=255.255.255. 0nfsargs=ip=:::::eth0:on root=/dev/nfs rw netdevwaitnfsboot=run setup;
setenv
bootargs ${defargs} ${nfsargs} ${setupargs} ${vidargs}; echo Booting via
DHCP/
TFTP/NFS...; usb start && dhcp && bootmsdargs=ip=off root=/dev/mmcblk1p1
rw,noatime rootfstype=ext3 rootwaitsdboot=run setup; setenv bootargs $ {defargs} ${sdargs} ${setupargs} ${vidargs}; echo Loading kernel and
rootfs
from MMC/SD Card...; mmc dev 1 &&
ext2l}serverip=192.168.10.1setup=setenv
setupargs gpt gpt_sector=${gptoffset} asix_mac=${ethaddr}
no_console_suspend=1
console=tty1 console=ttyS0,${baudrate}n8 debug_uartport=ls}
stderr=serial,lcdstdin=serial,usbkbdstdout=serial,lcdusbargs=root=/dev/sda2
rw,noatime rootwaitusbboot=run setup; setenv bootargs ${defargs}
${setupargs}
${usbargs} ${vidargs}; echo Booting from USB stick...; usb start &&
fatload
usb 0:1 ${loadamverify=novidargs=video=tegrafb0:640x480-16@60 Environment size: 1625/4092 bytesColibri T30 #
please give me a solution. regards,shobin.b _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot