Use some constants for the phy configuration instead of so many magic numbers.
Signed-off-by: Joe Hershberger joe.hershberger@ni.com ---
Changes in v2: -Fixed changed name from last-minute checkpatch line-length change
drivers/net/phy/marvell.c | 47 ++++++++++++++++++++++++++++++++++++----------- 1 file changed, 36 insertions(+), 11 deletions(-)
diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c index 4eeb0f6..ac13a67 100644 --- a/drivers/net/phy/marvell.c +++ b/drivers/net/phy/marvell.c @@ -82,6 +82,21 @@ #define MIIM_88E1310_PHY_RGMII_CTRL 21 #define MIIM_88E1310_PHY_PAGE 22
+/* 88E151x PHY defines */ +/* Page 3 registers */ +#define MIIM_88E151x_LED_FUNC_CTRL 16 +#define MIIM_88E151x_LED_FLD_SZ 4 +#define MIIM_88E151x_LED0_OFFS (0 * MIIM_88E151x_LED_FLD_SZ) +#define MIIM_88E151x_LED1_OFFS (1 * MIIM_88E151x_LED_FLD_SZ) +#define MIIM_88E151x_LED0_ACT 3 +#define MIIM_88E151x_LED1_100_1000_LINK 6 +#define MIIM_88E151x_LED_TIMER_CTRL 18 +#define MIIM_88E151x_INT_EN_OFFS 7 +/* Page 18 registers */ +#define MIIM_88E151x_GENERAL_CTRL 20 +#define MIIM_88E151x_MODE_SGMII 1 +#define MIIM_88E151x_RESET_OFFS 15 + /* Marvell 88E1011S */ static int m88e1011s_config(struct phy_device *phydev) { @@ -289,7 +304,7 @@ static int m88e1518_config(struct phy_device *phydev) */
/* EEE initialization */ - phy_write(phydev, MDIO_DEVAD_NONE, 22, 0x00ff); + phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x00ff); phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x214B); phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x2144); phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x0C28); @@ -298,21 +313,23 @@ static int m88e1518_config(struct phy_device *phydev) phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x214D); phy_write(phydev, MDIO_DEVAD_NONE, 17, 0xCC0C); phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x2159); - phy_write(phydev, MDIO_DEVAD_NONE, 22, 0x0000); + phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x0000);
/* SGMII-to-Copper mode initialization */ if (phydev->interface == PHY_INTERFACE_MODE_SGMII) { /* Select page 18 */ - phy_write(phydev, MDIO_DEVAD_NONE, 22, 18); + phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 18);
/* In reg 20, write MODE[2:0] = 0x1 (SGMII to Copper) */ - m88e1518_phy_writebits(phydev, 20, 0, 3, 1); + m88e1518_phy_writebits(phydev, MIIM_88E151x_GENERAL_CTRL, + 0, 3, MIIM_88E151x_MODE_SGMII);
/* PHY reset is necessary after changing MODE[2:0] */ - m88e1518_phy_writebits(phydev, 20, 15, 1, 1); + m88e1518_phy_writebits(phydev, MIIM_88E151x_GENERAL_CTRL, + MIIM_88E151x_RESET_OFFS, 1, 1);
/* Reset page selection */ - phy_write(phydev, MDIO_DEVAD_NONE, 22, 0); + phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0);
udelay(100); } @@ -324,17 +341,25 @@ static int m88e1518_config(struct phy_device *phydev) static int m88e1510_config(struct phy_device *phydev) { /* Select page 3 */ - phy_write(phydev, MDIO_DEVAD_NONE, 22, 3); + phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, + MIIM_88E1118_PHY_LED_PAGE);
/* Enable INTn output on LED[2] */ - m88e1518_phy_writebits(phydev, 18, 7, 1, 1); + m88e1518_phy_writebits(phydev, MIIM_88E151x_LED_TIMER_CTRL, + MIIM_88E151x_INT_EN_OFFS, 1, 1);
/* Configure LEDs */ - m88e1518_phy_writebits(phydev, 16, 0, 4, 3); /* LED[0]:0011 (ACT) */ - m88e1518_phy_writebits(phydev, 16, 4, 4, 6); /* LED[1]:0110 (LINK) */ + /* LED[0]:0011 (ACT) */ + m88e1518_phy_writebits(phydev, MIIM_88E151x_LED_FUNC_CTRL, + MIIM_88E151x_LED0_OFFS, MIIM_88E151x_LED_FLD_SZ, + MIIM_88E151x_LED0_ACT); + /* LED[1]:0110 (LINK 100/1000 Mbps) */ + m88e1518_phy_writebits(phydev, MIIM_88E151x_LED_FUNC_CTRL, + MIIM_88E151x_LED1_OFFS, MIIM_88E151x_LED_FLD_SZ, + MIIM_88E151x_LED1_100_1000_LINK);
/* Reset page selection */ - phy_write(phydev, MDIO_DEVAD_NONE, 22, 0); + phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0);
return m88e1518_config(phydev); }