This UART is not used in U-Boot, so there is no need to initialize it.
Signed-off-by: Lukasz Majewski lukma@denx.de ---
Changes in v2: None
board/liebherr/display5/common.c | 13 ------------- board/liebherr/display5/common.h | 1 - board/liebherr/display5/display5.c | 2 -- 3 files changed, 16 deletions(-)
diff --git a/board/liebherr/display5/common.c b/board/liebherr/display5/common.c index d2d174beaa0d..5e714076a49c 100644 --- a/board/liebherr/display5/common.c +++ b/board/liebherr/display5/common.c @@ -8,14 +8,6 @@ #include <asm/arch/mx6-pins.h> #include "common.h"
-iomux_v3_cfg_t const uart_pads[] = { - /* UART4 */ - MX6_PAD_CSI0_DAT12__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), - MX6_PAD_CSI0_DAT13__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), - MX6_PAD_CSI0_DAT16__UART4_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL), - MX6_PAD_CSI0_DAT17__UART4_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL), -}; - iomux_v3_cfg_t const uart_console_pads[] = { /* UART5 */ MX6_PAD_CSI0_DAT14__UART5_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), @@ -29,11 +21,6 @@ void displ5_set_iomux_uart_spl(void) SETUP_IOMUX_PADS(uart_console_pads); }
-void displ5_set_iomux_uart(void) -{ - SETUP_IOMUX_PADS(uart_pads); -} - iomux_v3_cfg_t const misc_pads_spl[] = { /* Emergency recovery pin */ MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL), diff --git a/board/liebherr/display5/common.h b/board/liebherr/display5/common.h index 2bbd934e7a70..4eb70dc42fb6 100644 --- a/board/liebherr/display5/common.h +++ b/board/liebherr/display5/common.h @@ -32,7 +32,6 @@ PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
void displ5_set_iomux_uart_spl(void); -void displ5_set_iomux_uart(void); void displ5_set_iomux_ecspi_spl(void); void displ5_set_iomux_usdhc_spl(void); void displ5_set_iomux_misc_spl(void); diff --git a/board/liebherr/display5/display5.c b/board/liebherr/display5/display5.c index 541e3e94a5eb..5713401ed954 100644 --- a/board/liebherr/display5/display5.c +++ b/board/liebherr/display5/display5.c @@ -174,8 +174,6 @@ int board_init(void) /* address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
- /* Setup iomux for non console UARTS */ - displ5_set_iomux_uart(); /* Setup misc (application specific) stuff */ SETUP_IOMUX_PADS(misc_pads);