Hi,
Thanks for the changes.
On Tue, Jul 25, 2017 at 12:30 PM, Wenyou Yang wenyou.yang@microchip.com wrote:
This series of patches are based and have been tested on the 'master' branch of the u-boot.git tree.
Tests were passed with a sama5d2 xplained board which embeds both SPI and QSPI controllers.
The following tests have been passed:
QSPI0 + Macronix MX25L25673G:
- probe: OK
- Fast Read 1-1-4 at offset 0x10000 (u-boot env): OK
- Page Program 1-1-4 at offset 0x10000: OK The Macronix datasheet tells that only Page Program 1-4-4 is supported, not Page Program 1-1-4, however it worked, I don't know why...
QSPI0 + Microchip SST26
- probe: OK
- Fast Read 1-1-4 at offset 0x10000 (u-boot env): OK
- Page Program 1-1-1 at offset 0x10000: OK SST26 memories support Page Program 1-4-4 but with the op code of Page Program 1-1-4, which is not standard so I don't use it.
QSPI0 + Adesto AT25DF321A
- probe: OK
- Fast Read 1-1-1 at offset 0x10000 (u-boot env): OK
- Page Program 1-1-1 at offset 0x10000: OK
SPI0 + Adesto AT25DF321A
- probe: OK
- Fast Read 1-1-1 at offset 0x6000 (u-boot env): OK
- Page Program 1-1-1 at offest 0x6000: OK
SPI1 + Atmel AT45
- probe: OK
- Read at offset 0 and other than 0: OK
- Write at offset 0 and other than 0: OK
During my tests, I used:
- setenv/saveenv, reboot, printenv
or
- sf probe, sf read, sf write, sf erase and sf update.
Changes in v3:
- Add the include <spi.h> to fix build error for corvus_defconfig.
Changes in v2:
- Rebase on the latest u-boot/master(2710d54f5).
Cyrille Pitchen (8): spi: add support of SPI flash commands sf: describe all SPI flash commands with 'struct spi_flash_command' sf: select the relevant SPI flash protocol for read and write commands sf: differentiate Page Program 1-1-4 and 1-4-4 sf: add 'addr_len' member to 'struct spi_flash' sf: add new option to support SPI flash above 16MiB sf: add support to Microchip SST26 QSPI memories sf: add driver for Atmel QSPI controller
Comments: How about writing struct spi_flash_command in spi_flash area (include/spi_flash.h)? and then write atmel_qspi with UCLASS_SPI_FLASH?
Testing: Basic testing works fine.
Issues: - Build issue: with zynq_microzed_defconfig drivers/mtd/spi/spi_flash.c: In function ‘spi_flash_scan’: drivers/mtd/spi/spi_flash.c:1049:7: warning: variable ‘above_16MB’ set but not used [-Wunused-but-set-variable] bool above_16MB; ^~~~~~~~~~ CC spl/lib/membuff.o
- issue with spi_flash_cmd_read_ops 4BAIS Need to calculate bank length only if BAR is in use. Otherwise, consider the given len as read_len.
Will send separate patch for this.
diff --git a/drivers/mtd/spi/spi_flash.c b/drivers/mtd/spi/spi_flash.c index 89ceae2..b5d8ef3 100644 --- a/drivers/mtd/spi/spi_flash.c +++ b/drivers/mtd/spi/spi_flash.c @@ -558,13 +558,15 @@ int spi_flash_cmd_read_ops(struct spi_flash *flash, u32 offset, if (ret < 0) return ret; bank_sel = flash->bank_curr; -#endif remain_len = ((SPI_FLASH_16MB_BOUN << flash->shift) * (bank_sel + 1)) - offset; if (len < remain_len) read_len = len; else read_len = remain_len; +#else + read_len = len; +#endif
cmd.addr = read_addr; cmd.data_len = read_len;
thanks!