When using DM_I2C the speed value supplied to setup_i2c() is not used, so this code required CONFIG_SYS_MXC_I2C[12]_SPEED to be defined to compile, but did not actually use them.
Change this so we no longer need to define an unused macro to compile in DM_I2C mode. Also make it more clear that they do not control the bus speed. Otherwise it is quite easy to mistakenly believe they are used to set the bus speed.
Cc: Heiko Schocher hs@denx.de Cc: Anatolij Gustschin agust@denx.de Signed-off-by: Trent Piepho tpiepho@impinj.com --- board/wandboard/wandboard.c | 19 ++++++++++++++----- 1 file changed, 14 insertions(+), 5 deletions(-)
diff --git a/board/wandboard/wandboard.c b/board/wandboard/wandboard.c index 69fbc8b690..9d7a94ff9d 100644 --- a/board/wandboard/wandboard.c +++ b/board/wandboard/wandboard.c @@ -46,6 +46,15 @@ DECLARE_GLOBAL_DATA_PTR; #define ETH_PHY_AR8035_POWER IMX_GPIO_NR(7, 13) #define REV_DETECTION IMX_GPIO_NR(2, 28)
+/* Speed defined in Kconfig is only applicable when not using DM_I2C. */ +#ifdef CONFIG_DM_I2C +#define I2C1_SPEED_NON_DM 0 +#define I2C2_SPEED_NON_DM 0 +#else +#define I2C1_SPEED_NON_DM CONFIG_SYS_MXC_I2C1_SPEED +#define I2C2_SPEED_NON_DM CONFIG_SYS_MXC_I2C2_SPEED +#endif + static bool with_pmic;
int dram_init(void) @@ -463,13 +472,13 @@ int board_init(void) gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
#if defined(CONFIG_VIDEO_IPUV3) - setup_i2c(1, CONFIG_SYS_MXC_I2C1_SPEED, 0x7f, &mx6dl_i2c2_pad_info); + setup_i2c(1, I2C1_SPEED_NON_DM, 0x7f, &mx6dl_i2c2_pad_info); if (is_mx6dq() || is_mx6dqp()) { - setup_i2c(1, CONFIG_SYS_MXC_I2C1_SPEED, 0x7f, &mx6q_i2c2_pad_info); - setup_i2c(2, CONFIG_SYS_MXC_I2C2_SPEED, 0x7f, &mx6q_i2c3_pad_info); + setup_i2c(1, I2C1_SPEED_NON_DM, 0x7f, &mx6q_i2c2_pad_info); + setup_i2c(2, I2C2_SPEED_NON_DM, 0x7f, &mx6q_i2c3_pad_info); } else { - setup_i2c(1, CONFIG_SYS_MXC_I2C1_SPEED, 0x7f, &mx6dl_i2c2_pad_info); - setup_i2c(2, CONFIG_SYS_MXC_I2C2_SPEED, 0x7f, &mx6dl_i2c3_pad_info); + setup_i2c(1, I2C1_SPEED_NON_DM, 0x7f, &mx6dl_i2c2_pad_info); + setup_i2c(2, I2C2_SPEED_NON_DM, 0x7f, &mx6dl_i2c3_pad_info); }
setup_display();