Use an if...endif construct to avoid needing to make everything depend on LED. Make SPL_LED depend on LED since that seems reasonable.
Signed-off-by: Simon Glass sjg@chromium.org ---
(no changes since v1)
drivers/led/Kconfig | 22 ++++++++++++---------- 1 file changed, 12 insertions(+), 10 deletions(-)
diff --git a/drivers/led/Kconfig b/drivers/led/Kconfig index 268118a6c3a..789113a92b5 100644 --- a/drivers/led/Kconfig +++ b/drivers/led/Kconfig @@ -9,6 +9,8 @@ config LED can provide access to board-specific LEDs. Use of the device tree for configuration is encouraged.
+if LED + config LED_BOOT bool "Enable LED boot support" help @@ -35,7 +37,7 @@ config LED_ACTIVITY
config LED_BCM6328 bool "LED Support for BCM6328" - depends on LED && ARCH_BMIPS + depends on ARCH_BMIPS help This option enables support for LEDs connected to the BCM6328 LED HW controller accessed via MMIO registers. @@ -46,7 +48,7 @@ config LED_BCM6328
config LED_BCM6358 bool "LED Support for BCM6358" - depends on LED && ARCH_BMIPS + depends on ARCH_BMIPS help This option enables support for LEDs connected to the BCM6358 LED HW controller accessed via MMIO registers. @@ -54,28 +56,28 @@ config LED_BCM6358
config LED_BCM6753 bool "LED Support for BCM6753" - depends on LED && BCM6855 + depends on BCM6855 help This option enables support for LEDs connected to the BCM6753 HW has blinking and fading capabilities and up to 32 LEDs can be controlled.
config LED_BCM6858 bool "LED Support for BCM6858" - depends on LED && (BCM6856 || BCM6858 || BCM63158) + depends on BCM6856 || BCM6858 || BCM63158 help This option enables support for LEDs connected to the BCM6858 HW has blinking capabilities and up to 32 LEDs can be controlled.
config LED_CORTINA bool "LED Support for Cortina Access CAxxxx SoCs" - depends on LED && (CORTINA_PLATFORM) + depends on CORTINA_PLATFORM help This option enables support for LEDs connected to the Cortina Access CAxxxx SOCs.
config LED_LP5562 bool "LED Support for LP5562" - depends on LED && DM_I2C + depends on DM_I2C help This option enables support for LEDs connected to the TI LP5562 4 channel I2C LED controller. Driver fully supports blink on the @@ -83,14 +85,13 @@ config LED_LP5562
config LED_PWM bool "LED PWM" - depends on LED && DM_PWM + depends on DM_PWM help Enable support for LEDs connected to PWM. Linux compatible ofdata.
config LED_BLINK bool "Support hardware LED blinking" - depends on LED help Some drivers can support automatic blinking of LEDs with a given period, without needing timers or extra code to handle the timing. @@ -99,7 +100,6 @@ config LED_BLINK
config LED_SW_BLINK bool "Support software LED blinking" - depends on LED select CYCLIC help Turns on led blinking implemented in the software, useful when @@ -122,7 +122,7 @@ config SPL_LED
config LED_GPIO bool "LED support for GPIO-connected LEDs" - depends on LED && DM_GPIO + depends on DM_GPIO help Enable support for LEDs which are connected to GPIO lines. These GPIOs may be on the SoC or some other device which provides GPIOs. @@ -136,6 +136,8 @@ config SPL_LED_GPIO This option is an SPL-variant of the LED_GPIO option. See the help of LED_GPIO for details.
+endif # LED + config LED_STATUS bool "Enable status LED API" help