The following restructuring and optimisations increase the SPI read performance from 1.3MiB/s (on da850) to 2.87MiB/s (on da830):
Remove continual revaluation of driver state from the core of the copy loop. State can not change during the copy loop, so it is possible to move these evaluations to before the copy loop.
Cost is more code space as loop variants are required for each set of possible configurations. The loops are simpler however, so the extra is only 128bytes on da830 with CONFIG_SPI_HALF_DUPLEX defined.
Unrolling the first copy loop iteration allows the TX buffer to be pre-loaded reducing SPI clock starvation.
Unrolling the last copy loop iteration removes testing for the final loop iteration every time round the loop.
Using the RX buffer empty flag as a transfer throttle allows the assumption that it is always safe to write to the TX buffer, so polling of TX buffer full flag can be removed.
Signed-off-by: Nick Thompson nick.thompson@ge.com
da850 and da830 are similar devices. The SPI module is common to both, but da850 uses DDR and da830 uses SDRAM. The EVM's might not actually be comparable, but they appear to be at least similar.
The speed was tested with a 8MiB transfer from SPI FLASH using:
sf read 0xc0008000 0 0x800000
drivers/spi/davinci_spi.c | 195 +++++++++++++++++++++++++++++-----------
This patch does not apply against Wolfgang's next. The patch should be against u-boot/next.
1 files changed, 128 insertions(+), 67 deletions(-)
diff --git a/drivers/spi/davinci_spi.c b/drivers/spi/davinci_spi.c index 08f837b..4518ecb 100644 --- a/drivers/spi/davinci_spi.c +++ b/drivers/spi/davinci_spi.c @@ -66,7 +66,7 @@ void spi_free_slave(struct spi_slave *slave) int spi_claim_bus(struct spi_slave *slave) { struct davinci_spi_slave *ds = to_davinci_spi(slave);
- unsigned int scalar, data1_reg_val = 0;
unsigned int scalar;
/* Enable the SPI hardware */ writel(SPIGCR0_SPIRST_MASK, &ds->regs->gcr0);
@@ -93,11 +93,6 @@ int spi_claim_bus(struct spi_slave *slave) writel(8 | (scalar << SPIFMT_PRESCALE_SHIFT) | (1 << SPIFMT_PHASE_SHIFT), &ds->regs->fmt0);
- /* hold cs active at end of transfer until explicitly de-asserted */
- data1_reg_val = (1 << SPIDAT1_CSHOLD_SHIFT) |
(slave->cs << SPIDAT1_CSNR_SHIFT);- writel(data1_reg_val, &ds->regs->dat1);
- /*
- Including a minor delay. No science here. Should be good even
with * no delay @@ -113,8 +108,7 @@ int spi_claim_bus(struct spi_slave *slave) writel(0, &ds->regs->lvl);
/* enable SPI */
- writel((readl(&ds->regs->gcr1) |
SPIGCR1_SPIENA_MASK), &ds->regs->gcr1);
- writel((readl(&ds->regs->gcr1) | SPIGCR1_SPIENA_MASK), &ds->regs-
gcr1);
return 0; } @@ -127,14 +121,125 @@ void spi_release_bus(struct spi_slave *slave) writel(SPIGCR0_SPIRST_MASK, &ds->regs->gcr0); }
+/*
- This functions needs to act like a macro to avoid pipeline reloads in
the
- loops below. Use always_inline. This gains us about 160KiB/s and the
bloat
- appears to be zero bytes (da830).
- */
+__attribute__((always_inline)) +static inline u32 davinci_spi_xfer_data(struct davinci_spi_slave *ds, u32 data) +{
- u32 buf_reg_val;
- /* send out data */
- writel(data, &ds->regs->dat1);
- /* wait for the data to clock in/out */
- while ((buf_reg_val = readl(&ds->regs->buf)) & SPIBUF_RXEMPTY_MASK)
;- return buf_reg_val;
+}
+static int davinci_spi_read(struct spi_slave *slave, unsigned int len,
u8 *rxp, unsigned long flags)+{
- struct davinci_spi_slave *ds = to_davinci_spi(slave);
- unsigned int data1_reg_val;
- /* enable CS hold, CS[n] and clear the data bits */
- data1_reg_val = ((1 << SPIDAT1_CSHOLD_SHIFT) |
(slave->cs << SPIDAT1_CSNR_SHIFT));- /* wait till TXFULL is deasserted */
- while (readl(&ds->regs->buf) & SPIBUF_TXFULL_MASK)
;- /* preload the TX buffer to avoid clock starvation */
- writel(data1_reg_val, &ds->regs->dat1);
- /* keep reading 1 byte until only 1 byte left */
- while ((len--) > 1)
*rxp++ = davinci_spi_xfer_data(ds, data1_reg_val);- /* clear CS hold when we reach the end */
- if (flags & SPI_XFER_END)
data1_reg_val &= ~(1 << SPIDAT1_CSHOLD_SHIFT);- /* read the last byte */
- *rxp = davinci_spi_xfer_data(ds, data1_reg_val);
- return 0;
+}
+static int davinci_spi_write(struct spi_slave *slave, unsigned int len,
const u8 *txp, unsigned long flags)+{
- struct davinci_spi_slave *ds = to_davinci_spi(slave);
- unsigned int data1_reg_val;
- /* enable CS hold and clear the data bits */
- data1_reg_val = ((1 << SPIDAT1_CSHOLD_SHIFT) |
(slave->cs << SPIDAT1_CSNR_SHIFT));- /* wait till TXFULL is deasserted */
- while (readl(&ds->regs->buf) & SPIBUF_TXFULL_MASK)
;- /* preload the TX buffer to avoid clock starvation */
- if (len > 2) {
writel(data1_reg_val | *txp++, &ds->regs->dat1);len--;- }
- /* keep writing 1 byte until only 1 byte left */
- while ((len--) > 1)
davinci_spi_xfer_data(ds, data1_reg_val | *txp++);- /* clear CS hold when we reach the end */
- if (flags & SPI_XFER_END)
data1_reg_val &= ~(1 << SPIDAT1_CSHOLD_SHIFT);- /* write the last byte */
- davinci_spi_xfer_data(ds, data1_reg_val | *txp);
- return 0;
+}
+#ifndef CONFIG_SPI_HALF_DUPLEX +static int davinci_spi_read_write(struct spi_slave *slave, unsigned int len,
u8 *rxp, const u8 *txp, unsigned long flags)+{
- struct davinci_spi_slave *ds = to_davinci_spi(slave);
- unsigned int data1_reg_val;
- /* enable CS hold and clear the data bits */
- data1_reg_val = ((1 << SPIDAT1_CSHOLD_SHIFT) |
(slave->cs << SPIDAT1_CSNR_SHIFT));- /* wait till TXFULL is deasserted */
- while (readl(&ds->regs->buf) & SPIBUF_TXFULL_MASK)
;- /* keep reading and writing 1 byte until only 1 byte left */
- while ((len--) > 1)
*rxp++ = davinci_spi_xfer_data(ds, data1_reg_val | *txp++);- /* clear CS hold when we reach the end */
- if (flags & SPI_XFER_END)
data1_reg_val &= ~(1 << SPIDAT1_CSHOLD_SHIFT);- /* read and write the last byte */
- *rxp = davinci_spi_xfer_data(ds, data1_reg_val | *txp);
- return 0;
+} +#endif
int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout, void *din, unsigned long flags) {
- struct davinci_spi_slave *ds = to_davinci_spi(slave);
- unsigned int len, data1_reg_val = readl(&ds->regs->dat1);
- unsigned int i_cnt = 0, o_cnt = 0, buf_reg_val;
- const u8 *txp = dout; /* dout can be NULL for read operation */
- u8 *rxp = din; /* din can be NULL for write operation */
unsigned int len;
if (bitlen == 0) /* Finish any previously submitted transfers */
@@ -154,63 +259,19 @@ int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
len = bitlen / 8;
- /* do an empty read to clear the current contents */
- readl(&ds->regs->buf);
- /* keep writing and reading 1 byte until done */
- while ((i_cnt < len) || (o_cnt < len)) {
/* read RX buffer and flags */buf_reg_val = readl(&ds->regs->buf);/* if data is available */if ((i_cnt < len) &&(buf_reg_val & SPIBUF_RXEMPTY_MASK) == 0) {/** If there is no read buffer simply* ignore the read character*/if (rxp)*rxp++ = buf_reg_val & 0xFF;/* increment read words count */i_cnt++;}/** if the tx buffer is empty and there* is still data to transmit*/if ((o_cnt < len) &&((buf_reg_val & SPIBUF_TXFULL_MASK) == 0)) {/* write the data */data1_reg_val &= ~0xFFFF;if (txp)data1_reg_val |= *txp++;/** Write to DAT1 is required to keep* the serial transfer going.* We just terminate when we reach the end.*/if ((o_cnt == (len - 1)) && (flags & SPI_XFER_END)) {/* clear CS hold */writel(data1_reg_val &~(1 << SPIDAT1_CSHOLD_SHIFT),&ds->regs->dat1);} else {/* enable CS hold and write TX register */data1_reg_val |= ((1 << SPIDAT1_CSHOLD_SHIFT) |(slave->cs << SPIDAT1_CSNR_SHIFT));writel(data1_reg_val, &ds->regs->dat1);}/* increment written words count */o_cnt++;}- }
- return 0;
- if (!dout)
return davinci_spi_read(slave, len, din, flags);- else if (!din)
return davinci_spi_write(slave, len, dout, flags);+#ifndef CONFIG_SPI_HALF_DUPLEX
- else
return davinci_spi_read_write(slave, len, din, dout, flags);+#endif
out: if (flags & SPI_XFER_END) {
writel(data1_reg_val &~(1 << SPIDAT1_CSHOLD_SHIFT), &ds->regs->dat1);
u8 dummy = 0;davinci_spi_write(slave, 1, &dummy, flags);}
1.7.0.4