Hi Stefan,
On 06/14/13 11:55, Stefan Roese wrote:
Add SPL U-Boot support to replace x-loader on the Compulab cm_t35 board. Currently only the 256MiB SDRAM board versions are supported.
Tested by booting via MMC and NAND.
Signed-off-by: Stefan Roese sr@denx.de Cc: Tom Rini trini@ti.com Cc: Igor Grinberg grinberg@compulab.co.il
board/compulab/cm_t35/cm_t35.c | 18 +++++++++++- include/configs/cm_t35.h | 64 ++++++++++++++++++++++++++++++++++++++++-- 2 files changed, 79 insertions(+), 3 deletions(-)
diff --git a/board/compulab/cm_t35/cm_t35.c b/board/compulab/cm_t35/cm_t35.c index b0b80e5..cd7882e 100644 --- a/board/compulab/cm_t35/cm_t35.c +++ b/board/compulab/cm_t35/cm_t35.c @@ -120,6 +120,22 @@ static inline int splash_load_from_nand(void) } #endif /* CONFIG_CMD_NAND */
+#ifdef CONFIG_SPL_BUILD +/*
- Routine: get_board_mem_timings
- Description: If we use SPL then there is no x-loader nor config header
- so we have to setup the DDR timings ourself on both banks.
- */
+void get_board_mem_timings(struct board_sdrc_timings *timings) +{
- timings->mr = MICRON_V_MR_165;
- timings->mcfg = MICRON_V_MCFG_165(256 << 20);
- timings->ctrla = MICRON_V_ACTIMA_165;
- timings->ctrlb = MICRON_V_ACTIMB_165;
- timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+} +#endif
I still haven't checked the timings... Hopefully, I will sometime during this week.
int board_splash_screen_prepare(void) { char *env_splashimage_value; @@ -443,7 +459,7 @@ void set_muxconf_regs(void) cm_t3730_set_muxconf(); }
-#ifdef CONFIG_GENERIC_MMC +#if defined(CONFIG_GENERIC_MMC) && !defined(CONFIG_SPL_BUILD) int board_mmc_getcd(struct mmc *mmc) { u8 val; diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h index c6e357a..b76810d 100644 --- a/include/configs/cm_t35.h +++ b/include/configs/cm_t35.h @@ -40,8 +40,6 @@ #define CONFIG_OMAP_GPIO #define CONFIG_CM_T3X /* working with CM-T35 and CM-T3730 */
-#define CONFIG_SYS_TEXT_BASE 0x80008000
#define CONFIG_SDRC /* The chip has SDRC controller */
#include <asm/arch/cpu.h> /* get chip and board defs */ @@ -341,4 +339,66 @@ #define CONFIG_BMP_16BPP #define CONFIG_SPLASH_SCREEN_PREPARE
+/* Defines for SPL */ +#define CONFIG_SPL +#define CONFIG_SPL_FRAMEWORK +#define CONFIG_SPL_NAND_SIMPLE +#define CONFIG_SPL_TEXT_BASE 0x40200800 +#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */ +#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
+#define CONFIG_SPL_BSS_START_ADDR 0x80000000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */ +#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */ +#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1 +#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
+#define CONFIG_SPL_BOARD_INIT +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBDISK_SUPPORT +#define CONFIG_SPL_I2C_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_MMC_SUPPORT +#define CONFIG_SPL_FAT_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC +#define CONFIG_SPL_GPIO_SUPPORT +#define CONFIG_SPL_POWER_SUPPORT +#define CONFIG_SPL_OMAP3_ID_NAND +#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
+/* NAND boot config */ +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_SYS_NAND_PAGE_COUNT 64 +#define CONFIG_SYS_NAND_PAGE_SIZE 2048 +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) +#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS +/*
- Use the ECC/OOB layout from omap_gpmc.h that matches your chip:
- SP vs LP, 8bit vs 16bit: GPMC_NAND_HW_ECC_LAYOUT
- */
+#define CONFIG_SYS_NAND_ECCPOS { 1, 2, 3, 4, 5, 6, 7, 8, 9, \
10, 11, 12 }+#define CONFIG_SYS_NAND_ECCSIZE 512 +#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+/*
- 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
- 64 bytes before this address should be set aside for u-boot.img's
- header. That is 0x800FFFC0--0x80100000 should not be used for any
- other needs.
- */
+#define CONFIG_SYS_TEXT_BASE 0x80100000
Now this is a problem. This breaks the backward compatibility with our X-Loader and we cannot just switch to 80100000...
+#define CONFIG_SYS_SPL_MALLOC_START 0x80208000 +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
#endif /* __CONFIG_H */