Add basic pinmux data for new K2G ICE evm. Also add pinmuxing for a generic K2G evm which includes I2C 0 and 1 used for board detection purposes.
Since multiple K2G boards are supported that means initially generic pinmuxing should be used when board detection hasn't ran. Once board detection runs the proper pinmuxing can be reran to match the board being ran on.
Signed-off-by: Franklin S Cooper Jr fcooper@ti.com Reviewed-by: Tom Rini trini@konsulko.com --- board/ti/ks2_evm/board_k2g.c | 2 ++ board/ti/ks2_evm/mux-k2g.h | 45 +++++++++++++++++++++++++++++++++++++++++++- 2 files changed, 46 insertions(+), 1 deletion(-)
diff --git a/board/ti/ks2_evm/board_k2g.c b/board/ti/ks2_evm/board_k2g.c index b4765f7..3622312 100644 --- a/board/ti/ks2_evm/board_k2g.c +++ b/board/ti/ks2_evm/board_k2g.c @@ -274,6 +274,8 @@ int embedded_dtb_select(void)
fdtdec_setup();
+ k2g_mux_config(); + k2g_reset_mux_config();
/* deassert FLASH_HOLD */ diff --git a/board/ti/ks2_evm/mux-k2g.h b/board/ti/ks2_evm/mux-k2g.h index 773f9b7..630103d 100644 --- a/board/ti/ks2_evm/mux-k2g.h +++ b/board/ti/ks2_evm/mux-k2g.h @@ -11,6 +11,22 @@ #include <asm/io.h> #include <asm/arch/mux-k2g.h> #include <asm/arch/hardware.h> +#include "board.h" + +struct pin_cfg k2g_generic_pin_cfg[] = { + /* UART0 */ + { 115, MODE(0) }, /* SOC_UART0_RXD */ + { 116, MODE(0) }, /* SOC_UART0_TXD */ + + /* I2C 0 */ + { 223, MODE(0) }, /* SOC_I2C0_SCL */ + { 224, MODE(0) }, /* SOC_I2C0_SDA */ + + /* I2C 1 */ + { 225, MODE(0) }, /* SOC_I2C1_SCL */ + { 226, MODE(0) }, /* SOC_I2C1_SDA */ + { MAX_PIN_N, } +};
struct pin_cfg k2g_evm_pin_cfg[] = { /* GPMC */ @@ -307,7 +323,34 @@ struct pin_cfg k2g_evm_pin_cfg[] = { { MAX_PIN_N, } };
+struct pin_cfg k2g_ice_evm_pin_cfg[] = { + /* MMC 1 */ + { 63, MODE(0) | PIN_PTD }, /* MMC1_DAT3.MMC1_DAT3 */ + { 64, MODE(0) | PIN_PTU }, /* MMC1_DAT2.MMC1_DAT2 */ + { 65, MODE(0) | PIN_PTU }, /* MMC1_DAT1.MMC1_DAT1 */ + { 66, MODE(0) | PIN_PTD }, /* MMC1_DAT0.MMC1_DAT0 */ + { 67, MODE(0) | PIN_PTD }, /* MMC1_CLK.MMC1_CLK */ + { 68, MODE(0) | PIN_PTD }, /* MMC1_CMD.MMC1_CMD */ + { 69, MODE(3) | PIN_PTU }, /* MMC1_SDCD.GPIO0_69 */ + { 70, MODE(0) | PIN_PTU }, /* MMC1_SDWP.MMC1_SDWP */ + { 71, MODE(0) | PIN_PTD }, /* MMC1_POW.MMC1_POW */ + + /* I2C 0 */ + { 223, MODE(0) }, /* SOC_I2C0_SCL */ + { 224, MODE(0) }, /* SOC_I2C0_SDA */ + { MAX_PIN_N, } +}; + void k2g_mux_config(void) { - configure_pin_mux(k2g_evm_pin_cfg); + if (!board_ti_was_eeprom_read()) { + configure_pin_mux(k2g_generic_pin_cfg); + } else if (board_is_k2g_gp()) { + configure_pin_mux(k2g_evm_pin_cfg); + } else if (board_is_k2g_ice()) { + configure_pin_mux(k2g_ice_evm_pin_cfg); + } else { + puts("Unknown board, cannot configure pinmux."); + hang(); + } }