On 06.04.20 09:15, Rayagonda Kokatanur wrote:
Get the watchdog platform clock from the DTS file using clk subsystem and use the same for calculating ticks in msec.
Signed-off-by: Rayagonda Kokatanur rayagonda.kokatanur@broadcom.com Signed-off-by: Bharat Kumar Reddy Gooty bharat.gooty@broadcom.com
Changes from v2: -Address review comments from Stefan Roese, Use clk subsystem to get the base frequency of device instead of dt parameter "clk_mhz".
Changes from v1: -Address review comments from Stefan Roese, Remove default timeout reading in probe() as it is read in include/wdt.h. Add paranthesis on multi-line statements.
drivers/watchdog/sp805_wdt.c | 19 +++++++++++++++++-- 1 file changed, 17 insertions(+), 2 deletions(-)
diff --git a/drivers/watchdog/sp805_wdt.c b/drivers/watchdog/sp805_wdt.c index ca3ccbe76c..d377ae0fc5 100644 --- a/drivers/watchdog/sp805_wdt.c +++ b/drivers/watchdog/sp805_wdt.c @@ -7,6 +7,7 @@
#include <asm/io.h> #include <common.h> +#include <clk.h> #include <dm/device.h> #include <dm/fdtaddr.h> #include <dm/read.h> @@ -34,6 +35,7 @@ DECLARE_GLOBAL_DATA_PTR;
struct sp805_wdt_priv { void __iomem *reg;
unsigned long clk_rate; };
static int sp805_wdt_reset(struct udevice *dev)
@@ -63,8 +65,13 @@ static int sp805_wdt_start(struct udevice *dev, u64 timeout, ulong flags) * set 120s, the gd->bus_clk is less than 1145MHz, the load_value will * not overflow. */
- load_value = (gd->bus_clk) /
(2 * 1000 * SYS_FSL_WDT_CLK_DIV) * load_time;
if (gd->bus_clk) {
load_value = (gd->bus_clk) /(2 * 1000 * SYS_FSL_WDT_CLK_DIV) * load_time;} else {
/* platform provide clk */load_value = (timeout / 2) * (priv->clk_rate / 1000);}
writel(UNLOCK, priv->reg + WDTLOCK); writel(load_value, priv->reg + WDTLOAD);
@@ -105,11 +112,19 @@ static int sp805_wdt_probe(struct udevice *dev) static int sp805_wdt_ofdata_to_platdata(struct udevice *dev) { struct sp805_wdt_priv *priv = dev_get_priv(dev);
struct clk clk;
int ret;
priv->reg = (void __iomem *)dev_read_addr(dev); if (IS_ERR(priv->reg)) return PTR_ERR(priv->reg);
ret = clk_get_by_index(dev, 0, &clk);
if (!ret)
priv->clk_rate = clk_get_rate(&clk);else
return -EINVAL;
Thanks for addresses this. Looks much better now, without all the ad-hoc DT bindings.
Though I suspect that some boards using this WDT driver do not fully support the CLK API for this device. That's why we still have this "bus_clk" in global-data here. Some NXP folks might test and report if this works for them. Otherwise sp805_wdt_ofdata_to_platdata() should not fail if clk_get_by_index() returns with error.
Thanks, Stefan