This patch adds Microchip MPFS Icicle Kit support. For now, only NS16550 Serial, Microchip clock, Cadence eMMC and MACB drivers are enabled. The Microchip MPFS Icicle defconfig by default builds U-Boot for S-Mode because U-Boot on Microchip PolarFire SoC will run in S-Mode as payload of HSS + OpenSBI.
Signed-off-by: Padmarao Begari padmarao.begari@microchip.com Reviewed-by: Anup Patel anup.patel@wdc.com Reviewed-by: Bin Meng bin.meng@windriver.com Tested-by: Bin Meng bin.meng@windriver.com --- board/microchip/mpfs_icicle/Kconfig | 23 ++++++ board/microchip/mpfs_icicle/mpfs_icicle.c | 99 ++++++++++++++++++++++- configs/microchip_mpfs_icicle_defconfig | 9 ++- include/configs/microchip_mpfs_icicle.h | 59 +++++--------- 4 files changed, 145 insertions(+), 45 deletions(-)
diff --git a/board/microchip/mpfs_icicle/Kconfig b/board/microchip/mpfs_icicle/Kconfig index bf8e1a13ec..4678462378 100644 --- a/board/microchip/mpfs_icicle/Kconfig +++ b/board/microchip/mpfs_icicle/Kconfig @@ -20,7 +20,30 @@ config BOARD_SPECIFIC_OPTIONS # dummy def_bool y select GENERIC_RISCV select BOARD_EARLY_INIT_F + select BOARD_LATE_INIT imply SMP + imply CLK_CCF + imply CLK_MPFS imply SYS_NS16550 + imply CMD_DHCP + imply CMD_EXT2 + imply CMD_EXT4 + imply CMD_FAT + imply CMD_FS_GENERIC + imply CMD_NET + imply CMD_PING + imply CMD_MMC + imply DOS_PARTITION + imply EFI_PARTITION + imply IP_DYN + imply ISO_PARTITION + imply MACB + imply MII + imply PHY_LIB + imply PHY_VITESSE + imply MMC + imply MMC_WRITE + imply MMC_SDHCI + imply MMC_SDHCI_CADENCE
endif diff --git a/board/microchip/mpfs_icicle/mpfs_icicle.c b/board/microchip/mpfs_icicle/mpfs_icicle.c index 8381361ec3..0e34409067 100644 --- a/board/microchip/mpfs_icicle/mpfs_icicle.c +++ b/board/microchip/mpfs_icicle/mpfs_icicle.c @@ -6,10 +6,49 @@
#include <common.h> #include <dm.h> +#include <env.h> #include <init.h> #include <asm/io.h>
-#define MPFS_SYSREG_SOFT_RESET ((unsigned int *)0x20002088) +DECLARE_GLOBAL_DATA_PTR; + +#define MPFS_SYSREG_SOFT_RESET ((unsigned int *)0x20002088) +#define MPFS_SYS_SERVICE_CR ((unsigned int *)0x37020050) +#define MPFS_SYS_SERVICE_SR ((unsigned int *)0x37020054) +#define MPFS_SYS_SERVICE_MAILBOX ((unsigned char *)0x37020800) + +#define PERIPH_RESET_VALUE 0x1e8u +#define SERVICE_CR_REQ 0x1u +#define SERVICE_SR_BUSY 0x2u + +static void read_device_serial_number(u8 *response, u8 response_size) +{ + u8 idx; + u8 *response_buf; + unsigned int val; + + response_buf = (u8 *)response; + + writel(SERVICE_CR_REQ, MPFS_SYS_SERVICE_CR); + /* + * REQ bit will remain set till the system controller starts + * processing. + */ + do { + val = readl(MPFS_SYS_SERVICE_CR); + } while (SERVICE_CR_REQ == (val & SERVICE_CR_REQ)); + + /* + * Once system controller starts processing the busy bit will + * go high and service is completed when busy bit is gone low + */ + do { + val = readl(MPFS_SYS_SERVICE_SR); + } while (SERVICE_SR_BUSY == (val & SERVICE_SR_BUSY)); + + for (idx = 0; idx < response_size; idx++) + response_buf[idx] = readb(MPFS_SYS_SERVICE_MAILBOX + idx); +}
int board_init(void) { @@ -22,10 +61,64 @@ int board_early_init_f(void) { unsigned int val;
- /* Reset uart peripheral */ + /* Reset uart, mmc peripheral */ val = readl(MPFS_SYSREG_SOFT_RESET); - val = (val & ~(1u << 5u)); + val = (val & ~(PERIPH_RESET_VALUE)); writel(val, MPFS_SYSREG_SOFT_RESET);
return 0; } + +int board_late_init(void) +{ + u32 ret; + u32 node; + u8 idx; + u8 device_serial_number[16] = { 0 }; + unsigned char mac_addr[6]; + char icicle_mac_addr[20]; + void *blob = (void *)gd->fdt_blob; + + node = fdt_path_offset(blob, "ethernet0"); + if (node < 0) { + printf("No ethernet0 path offset\n"); + return -ENODEV; + } + + ret = fdtdec_get_byte_array(blob, node, "local-mac-address", mac_addr, 6); + if (ret) { + printf("No local-mac-address property\n"); + return -EINVAL; + } + + read_device_serial_number(device_serial_number, 16); + + /* Update MAC address with device serial number */ + mac_addr[0] = 0x00; + mac_addr[1] = 0x04; + mac_addr[2] = 0xA3; + mac_addr[3] = device_serial_number[2]; + mac_addr[4] = device_serial_number[1]; + mac_addr[5] = device_serial_number[0]; + + ret = fdt_setprop(blob, node, "local-mac-address", mac_addr, 6); + if (ret) { + printf("Error setting local-mac-address property\n"); + return -ENODEV; + } + + icicle_mac_addr[0] = '['; + + sprintf(&icicle_mac_addr[1], "%pM", mac_addr); + + icicle_mac_addr[18] = ']'; + icicle_mac_addr[19] = '\0'; + + for (idx = 0; idx < 20; idx++) { + if (icicle_mac_addr[idx] == ':') + icicle_mac_addr[idx] = ' '; + } + env_set("icicle_mac_addr", icicle_mac_addr); + + return 0; +} diff --git a/configs/microchip_mpfs_icicle_defconfig b/configs/microchip_mpfs_icicle_defconfig index 2977966473..9abbc18a89 100644 --- a/configs/microchip_mpfs_icicle_defconfig +++ b/configs/microchip_mpfs_icicle_defconfig @@ -1,12 +1,15 @@ CONFIG_RISCV=y CONFIG_ENV_SIZE=0x2000 CONFIG_TARGET_MICROCHIP_ICICLE=y -CONFIG_NR_CPUS=5 CONFIG_ARCH_RV64I=y +CONFIG_RISCV_SMODE=y +CONFIG_SBI_V01=y +CONFIG_DEFAULT_DEVICE_TREE="microchip-mpfs-icicle-kit" +CONFIG_DISTRO_DEFAULTS=y +CONFIG_DISPLAY_CPUINFO=y +CONFIG_DISPLAY_BOARDINFO=y CONFIG_FIT=y -CONFIG_BOOTDELAY=3 CONFIG_SYS_PROMPT="RISC-V # " -CONFIG_OF_PRIOR_STAGE=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_BOOTP_SEND_HOSTNAME=y CONFIG_DM_MTD=y diff --git a/include/configs/microchip_mpfs_icicle.h b/include/configs/microchip_mpfs_icicle.h index 8a7470545b..24990370cf 100644 --- a/include/configs/microchip_mpfs_icicle.h +++ b/include/configs/microchip_mpfs_icicle.h @@ -7,53 +7,34 @@ #ifndef __CONFIG_H #define __CONFIG_H
-/* - * CPU and Board Configuration Options - */ +#include <linux/sizes.h>
-/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_SDRAM_BASE 0x80000000 +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_2M)
-/* - * Print Buffer Size - */ -#define CONFIG_SYS_PBSIZE \ - (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_2M)
-/* - * max number of command args - */ -#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_MALLOC_LEN SZ_8M
-/* - * Boot Argument Buffer Size - */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -/* - * Size of malloc() pool - * 512kB is suggested, (CONFIG_ENV_SIZE + 128 * 1024) was not enough - */ -#define CONFIG_SYS_MALLOC_LEN (512 << 10) +#define CONFIG_SYS_BOOTM_LEN SZ_64M
-/* - * Physical Memory Map - */ -#define PHYS_SDRAM_0 0x80000000 /* SDRAM Bank #1 */ -#define PHYS_SDRAM_0_SIZE 0x40000000 /* 1 GB */ -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_0 +#define CONFIG_STANDALONE_LOAD_ADDR 0x80200000
-/* Init Stack Pointer */ -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x200000) +/* Environment options */
-#define CONFIG_SYS_LOAD_ADDR 0x80000000 /* SDRAM */ +#define BOOT_TARGET_DEVICES(func) \ + func(MMC, mmc, 0) \ + func(DHCP, dhcp, na)
-/* - * memtest works on DRAM - */ +#include <config_distro_bootcmd.h>
-/* When we use RAM as ENV */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + "bootm_size=0x10000000\0" \ + "kernel_addr_r=0x84000000\0" \ + "fdt_addr_r=0x88000000\0" \ + "scriptaddr=0x88100000\0" \ + "pxefile_addr_r=0x88200000\0" \ + "ramdisk_addr_r=0x88300000\0" \ + BOOTENV
#endif /* __CONFIG_H */