Make EHCI power and overcurrent polarities configurable. If not set, these new configurartions keep the default register values so that existing board files do not have to be changed.
Signed-off-by: Benoît Thébaudeau benoit.thebaudeau@advansee.com Cc: Marek Vasut marex@denx.de Cc: Stefano Babic sbabic@denx.de --- .../drivers/usb/host/ehci-mx5.c | 51 ++++++++++++++++++++ .../include/usb/ehci-fsl.h | 10 ++-- 2 files changed, 57 insertions(+), 4 deletions(-)
diff --git u-boot-usb-76454b2.orig/drivers/usb/host/ehci-mx5.c u-boot-usb-76454b2/drivers/usb/host/ehci-mx5.c index 7da1398..52aeae5 100644 --- u-boot-usb-76454b2.orig/drivers/usb/host/ehci-mx5.c +++ u-boot-usb-76454b2/drivers/usb/host/ehci-mx5.c @@ -44,24 +44,33 @@ /* USB_CTRL */ #define MXC_OTG_UCTRL_OWIE_BIT (1 << 27) /* OTG wakeup intr enable */ #define MXC_OTG_UCTRL_OPM_BIT (1 << 24) /* OTG power mask */ +#define MXC_OTG_UCTRL_O_PWR_POL_BIT (1 << 24) /* OTG power pin polarity */ #define MXC_H1_UCTRL_H1UIE_BIT (1 << 12) /* Host1 ULPI interrupt enable */ #define MXC_H1_UCTRL_H1WIE_BIT (1 << 11) /* HOST1 wakeup intr enable */ #define MXC_H1_UCTRL_H1PM_BIT (1 << 8) /* HOST1 power mask */ +#define MXC_H1_UCTRL_H1_PWR_POL_BIT (1 << 8) /* HOST1 power pin polarity */
/* USB_PHY_CTRL_FUNC */ +#define MXC_OTG_PHYCTRL_OC_POL_BIT (1 << 9) /* OTG Polarity of Overcurrent */ #define MXC_OTG_PHYCTRL_OC_DIS_BIT (1 << 8) /* OTG Disable Overcurrent Event */ +#define MXC_H1_OC_POL_BIT (1 << 6) /* UH1 Polarity of Overcurrent */ #define MXC_H1_OC_DIS_BIT (1 << 5) /* UH1 Disable Overcurrent Event */ +#define MXC_OTG_PHYCTRL_PWR_POL_BIT (1 << 3) /* OTG Power Pin Polarity */
/* USBH2CTRL */ +#define MXC_H2_UCTRL_H2_OC_POL_BIT (1 << 31) #define MXC_H2_UCTRL_H2_OC_DIS_BIT (1 << 30) #define MXC_H2_UCTRL_H2UIE_BIT (1 << 8) #define MXC_H2_UCTRL_H2WIE_BIT (1 << 7) #define MXC_H2_UCTRL_H2PM_BIT (1 << 4) +#define MXC_H2_UCTRL_H2_PWR_POL_BIT (1 << 4)
/* USBH3CTRL */ +#define MXC_H3_UCTRL_H3_OC_POL_BIT (1 << 31) #define MXC_H3_UCTRL_H3_OC_DIS_BIT (1 << 30) #define MXC_H3_UCTRL_H3UIE_BIT (1 << 8) #define MXC_H3_UCTRL_H3WIE_BIT (1 << 7) +#define MXC_H3_UCTRL_H3_PWR_POL_BIT (1 << 4)
/* USB_CTRL_1 */ #define MXC_USB_CTRL_UH1_EXT_CLK_EN (1 << 25) @@ -151,12 +160,22 @@ int mxc_set_usbcontrol(int port, unsigned int flags) if (flags & MXC_EHCI_INTERNAL_PHY) { v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET); + if (flags & MXC_EHCI_OC_PIN_ACTIVE_LOW) + v |= MXC_OTG_PHYCTRL_OC_POL_BIT; + else + v &= ~MXC_OTG_PHYCTRL_OC_POL_BIT; if (flags & MXC_EHCI_POWER_PINS_ENABLED) /* OC/USBPWR is used */ v &= ~MXC_OTG_PHYCTRL_OC_DIS_BIT; else /* OC/USBPWR is not used */ v |= MXC_OTG_PHYCTRL_OC_DIS_BIT; +#ifdef CONFIG_MX51 + if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH) + v |= MXC_OTG_PHYCTRL_PWR_POL_BIT; + else + v &= ~MXC_OTG_PHYCTRL_PWR_POL_BIT; +#endif __raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET);
@@ -167,6 +186,12 @@ int mxc_set_usbcontrol(int port, unsigned int flags) else v |= MXC_OTG_UCTRL_OPM_BIT; #endif +#ifdef CONFIG_MX53 + if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH) + v |= MXC_OTG_UCTRL_O_PWR_POL_BIT; + else + v &= ~MXC_OTG_UCTRL_O_PWR_POL_BIT; +#endif __raw_writel(v, usbother_base + MXC_USBCTRL_OFFSET); } break; @@ -186,9 +211,19 @@ int mxc_set_usbcontrol(int port, unsigned int flags) else v |= MXC_H1_UCTRL_H1PM_BIT; /* HOST1 power mask used */ #endif +#ifdef CONFIG_MX53 + if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH) + v |= MXC_H1_UCTRL_H1_PWR_POL_BIT; + else + v &= ~MXC_H1_UCTRL_H1_PWR_POL_BIT; +#endif __raw_writel(v, usbother_base + MXC_USBCTRL_OFFSET);
v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET); + if (flags & MXC_EHCI_OC_PIN_ACTIVE_LOW) + v |= MXC_H1_OC_POL_BIT; + else + v &= ~MXC_H1_OC_POL_BIT; if (flags & MXC_EHCI_POWER_PINS_ENABLED) v &= ~MXC_H1_OC_DIS_BIT; /* OC is used */ else @@ -205,10 +240,18 @@ int mxc_set_usbcontrol(int port, unsigned int flags) v |= MXC_H2_UCTRL_H2PM_BIT; /* HOST2 power mask used */ #endif #ifdef CONFIG_MX53 + if (flags & MXC_EHCI_OC_PIN_ACTIVE_LOW) + v |= MXC_H2_UCTRL_H2_OC_POL_BIT; + else + v &= ~MXC_H2_UCTRL_H2_OC_POL_BIT; if (flags & MXC_EHCI_POWER_PINS_ENABLED) v &= ~MXC_H2_UCTRL_H2_OC_DIS_BIT; /* OC is used */ else v |= MXC_H2_UCTRL_H2_OC_DIS_BIT; /* OC is not used */ + if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH) + v |= MXC_H2_UCTRL_H2_PWR_POL_BIT; + else + v &= ~MXC_H2_UCTRL_H2_PWR_POL_BIT; #endif
__raw_writel(v, usbother_base + MXC_USBH2CTRL_OFFSET); @@ -216,10 +259,18 @@ int mxc_set_usbcontrol(int port, unsigned int flags) #ifdef CONFIG_MX53 case 3: /* Host 3 ULPI */ v = __raw_readl(usbother_base + MXC_USBH3CTRL_OFFSET); + if (flags & MXC_EHCI_OC_PIN_ACTIVE_LOW) + v |= MXC_H3_UCTRL_H3_OC_POL_BIT; + else + v &= ~MXC_H3_UCTRL_H3_OC_POL_BIT; if (flags & MXC_EHCI_POWER_PINS_ENABLED) v &= ~MXC_H3_UCTRL_H3_OC_DIS_BIT; /* OC is used */ else v |= MXC_H3_UCTRL_H3_OC_DIS_BIT; /* OC is not used */ + if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH) + v |= MXC_H3_UCTRL_H3_PWR_POL_BIT; + else + v &= ~MXC_H3_UCTRL_H3_PWR_POL_BIT;
__raw_writel(v, usbother_base + MXC_USBH3CTRL_OFFSET); break; diff --git u-boot-usb-76454b2.orig/include/usb/ehci-fsl.h u-boot-usb-76454b2/include/usb/ehci-fsl.h index 4dee5b0..a1438d6 100644 --- u-boot-usb-76454b2.orig/include/usb/ehci-fsl.h +++ u-boot-usb-76454b2/include/usb/ehci-fsl.h @@ -266,11 +266,13 @@ struct usb_ehci { #define MXC_EHCI_INTERFACE_MASK (0xf)
#define MXC_EHCI_POWER_PINS_ENABLED (1 << 5) -#define MXC_EHCI_TTL_ENABLED (1 << 6) +#define MXC_EHCI_PWR_PIN_ACTIVE_HIGH (1 << 6) +#define MXC_EHCI_OC_PIN_ACTIVE_LOW (1 << 7) +#define MXC_EHCI_TTL_ENABLED (1 << 8)
-#define MXC_EHCI_INTERNAL_PHY (1 << 7) -#define MXC_EHCI_IPPUE_DOWN (1 << 8) -#define MXC_EHCI_IPPUE_UP (1 << 9) +#define MXC_EHCI_INTERNAL_PHY (1 << 9) +#define MXC_EHCI_IPPUE_DOWN (1 << 10) +#define MXC_EHCI_IPPUE_UP (1 << 11)
/* Board-specific initialization */ int board_ehci_hcd_init(int port);