LX2160A Soc is based on Layerscape Chassis Generation 3.2 Architecture. Features: 16 ARM v8 Cortex-A72 cores in 8 cluster, CCN508, SEC, two 64-bit DDR4 memory controller, RGMII, 8 I2C controllers, 3 serdes modules, USB 3.0, SATA, 4 PL011 SBSA UARTs, 4 TZASC instances, etc.
SoC personalites: LX2120A is SoC with Twelve 64-bit ARM v8 Cortex-A72 CPUs LX2080A is SoC with Eight 64-bit ARM v8 Cortex-A72 CPUs
Signed-off-by: Bao Xiaowei xiaowei.bao@nxp.com Signed-off-by: Yinbo Zhu yinbo.zhu@nxp.com Signed-off-by: Hou Zhiqiang Zhiqiang.Hou@nxp.com Signed-off-by: Meenakshi Aggarwal meenakshi.aggarwal@nxp.com Signed-off-by: Vabhav Sharma vabhav.sharma@nxp.com Signed-off-by: Sriram Dash sriram.dash@nxp.com Signed-off-by: Priyanka Jain priyanka.jain@nxp.com --- arch/arm/cpu/armv8/fsl-layerscape/Kconfig | 50 ++++++- arch/arm/cpu/armv8/fsl-layerscape/Makefile | 6 +- arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc | 57 ++++++++ .../cpu/armv8/fsl-layerscape/fsl_lsch3_serdes.c | 36 ++++++ arch/arm/cpu/armv8/fsl-layerscape/lx2160a_serdes.c | 132 +++++++++++++++++++ arch/arm/dts/fsl-lx2160a.dtsi | 143 +++++++++++++++++++++ arch/arm/include/asm/arch-fsl-layerscape/config.h | 56 ++++++++ arch/arm/include/asm/arch-fsl-layerscape/cpu.h | 3 + .../include/asm/arch-fsl-layerscape/fsl_serdes.h | 28 ++++ .../include/asm/arch-fsl-layerscape/immap_lsch3.h | 28 +++- arch/arm/include/asm/arch-fsl-layerscape/soc.h | 8 +- .../asm/arch-fsl-layerscape/stream_id_lsch3.h | 9 +- drivers/net/ldpaa_eth/Makefile | 3 +- drivers/net/ldpaa_eth/lx2160a.c | 107 +++++++++++++++ 14 files changed, 655 insertions(+), 11 deletions(-) create mode 100644 arch/arm/cpu/armv8/fsl-layerscape/lx2160a_serdes.c create mode 100644 arch/arm/dts/fsl-lx2160a.dtsi create mode 100644 drivers/net/ldpaa_eth/lx2160a.c
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/Kconfig b/arch/arm/cpu/armv8/fsl-layerscape/Kconfig index 81eec78..6c0d6fe 100644 --- a/arch/arm/cpu/armv8/fsl-layerscape/Kconfig +++ b/arch/arm/cpu/armv8/fsl-layerscape/Kconfig @@ -170,6 +170,41 @@ config ARCH_LS2080A imply DISTRO_DEFAULTS imply PANIC_HANG
+config ARCH_LX2160A + bool + select ARMV8_SET_SMPEN + select FSL_LSCH3 + select NXP_LSCH3_2 + select SYS_HAS_SERDES + select SYS_FSL_SRDS_1 + select SYS_FSL_SRDS_2 + select SYS_NXP_SRDS_3 + select SYS_FSL_DDR + select SYS_FSL_DDR_LE + select SYS_FSL_DDR_VER_50 + select SYS_FSL_EC1 + select SYS_FSL_EC2 + select SYS_FSL_HAS_RGMII + select SYS_FSL_HAS_SEC + select SYS_FSL_HAS_DDR4 + select SYS_FSL_SEC_COMPAT_5 + select SYS_FSL_SEC_LE + select ARCH_EARLY_INIT_R + select BOARD_EARLY_INIT_F + select SYS_I2C_MXC + select SYS_I2C_MXC_I2C1 + select SYS_I2C_MXC_I2C2 + select SYS_I2C_MXC_I2C3 + select SYS_I2C_MXC_I2C4 + select SYS_I2C_MXC_I2C5 + select SYS_I2C_MXC_I2C6 + select SYS_I2C_MXC_I2C7 + select SYS_I2C_MXC_I2C8 + imply DISTRO_DEFAULTS + imply PANIC_HANG + imply SCSI + imply SCSI_AHCI + config FSL_LSCH2 bool select SYS_FSL_HAS_CCI400 @@ -185,7 +220,7 @@ config FSL_LSCH3_2
config FSL_MC_ENET bool "Management Complex network" - depends on ARCH_LS2080A || ARCH_LS1088A + depends on ARCH_LS2080A || ARCH_LS1088A || ARCH_LX2160A default y select RESV_RAM help @@ -202,6 +237,7 @@ config FSL_PCIE_COMPAT default "fsl,ls1046a-pcie" if ARCH_LS1046A default "fsl,ls2080a-pcie" if ARCH_LS2080A default "fsl,ls1088a-pcie" if ARCH_LS1088A + default "fsl,lx2160a-pcie" if ARCH_LX2160A help This compatible is used to find pci controller node in Kernel DT to complete fixup. @@ -300,6 +336,7 @@ config MAX_CPUS default 4 if ARCH_LS1046A default 16 if ARCH_LS2080A default 8 if ARCH_LS1088A + default 16 if ARCH_LX2160A default 1 help Set this number to the maximum number of possible CPUs in the SoC. @@ -404,6 +441,7 @@ config SYS_FSL_DSPI_CLK_DIV config SYS_FSL_DUART_CLK_DIV int "DUART clock divider" default 1 if ARCH_LS1043A + default 4 if ARCH_LX2160A default 2 help This is the divider that is used to derive DUART clock from Platform @@ -464,13 +502,15 @@ config RESV_RAM config SYS_FSL_EC1 bool help - Ethernet controller 1, this is connected to MAC3. + Ethernet controller 1, this is connected to + MAC17 for LX2160A or to MAC3 for other SoCs Provides DPAA2 capabilities
config SYS_FSL_EC2 bool help - Ethernet controller 2, this is connected to MAC4. + Ethernet controller 2, this is connected to + MAC18 for LX2160A or to MAC4 for other SoCs Provides DPAA2 capabilities
config SYS_FSL_ERRATUM_A008336 @@ -506,13 +546,13 @@ config SYS_FSL_HAS_RGMII config SYS_MC_RSV_MEM_ALIGN hex "Management Complex reserved memory alignment" depends on RESV_RAM - default 0x20000000 if ARCH_LS2080A || ARCH_LS1088A + default 0x20000000 if ARCH_LS2080A || ARCH_LS1088A || ARCH_LX2160A help Reserved memory needs to be aligned for MC to use. Default value is 512MB.
config SPL_LDSCRIPT - default "arch/arm/cpu/armv8/u-boot-spl.lds" if ARCH_LS1043A || ARCH_LS1046A || ARCH_LS2080A + default "arch/arm/cpu/armv8/u-boot-spl.lds" if ARCH_LS1043A || ARCH_LS1046A || ARCH_LS2080A || ARCH_LX2160A
config HAS_FSL_XHCI_USB bool diff --git a/arch/arm/cpu/armv8/fsl-layerscape/Makefile b/arch/arm/cpu/armv8/fsl-layerscape/Makefile index 5d6f68a..4eaa90c 100644 --- a/arch/arm/cpu/armv8/fsl-layerscape/Makefile +++ b/arch/arm/cpu/armv8/fsl-layerscape/Makefile @@ -1,5 +1,5 @@ # SPDX-License-Identifier: GPL-2.0+ -# +# Copyright 2018 NXP # Copyright 2014-2015, Freescale Semiconductor
obj-y += cpu.o @@ -22,6 +22,10 @@ obj-$(CONFIG_SYS_HAS_SERDES) += fsl_lsch2_serdes.o endif endif
+ifneq ($(CONFIG_ARCH_LX2160A),) +obj-$(CONFIG_SYS_HAS_SERDES) += lx2160a_serdes.o +endif + ifneq ($(CONFIG_ARCH_LS2080A),) obj-$(CONFIG_SYS_HAS_SERDES) += ls2080a_serdes.o endif diff --git a/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc b/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc index 276ab90..a0e2621 100644 --- a/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc +++ b/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc @@ -7,6 +7,7 @@ SoC overview 5. LS1046A 6. LS2088A 7. LS2081A + 8. LX2160A
LS1043A --------- @@ -271,3 +272,59 @@ Refer to LS2084A(LS2088A) section above for details. It has one more similar SoC personality 1)LS2041A, few difference w.r.t. LS2081A: a) Four 64-bit ARM v8 Cortex-A72 CPUs + +LX2160A +-------- +The QorIQ LX2160A processor is built in the 16FFC process on +the Layerscape architecture combining sixteen ARM A72 processor +cores with advanced, high-performance datapath acceleration and +network, peripheral interfaces required for networking, wireless +infrastructure, storage, and general-purpose embedded applications. + +LX2160A is compliant with the Layerscape Chassis Generation 3.2. + +The LX2160A SoC includes the following function and features: + Sixteen 32-bit / 64-bit ARM v8 A72 CPUs + Cache Coherent Interconnect Fabric (CCN508 aka “Eliot”) + Two 64-bit 3.2GT/s DDR4 SDRAM memory controllers with ECC. + Data path acceleration architecture (DPAA2) + 24 Serdes lanes at up to 25 GHz + Ethernet interfaces + Single WRIOP tile supporting 130Gbps using 18 MACs + Support for 10G-SXGMII (aka USXGMII). + Support for SGMII (and 1000Base-KX) + Support for XFI (and 10GBase-KR) + Support for CAUI4 (100G); CAUI2 (50G) and 25G-AUI(25G). + Support for XLAUI (and 40GBase-KR4) for 40G. + Support for two RGMII parallel interfaces. + Energy efficient Ethernet support (802.3az) + IEEE 1588 support. + High-speed peripheral interfaces + Two PCIe Gen 4.0 8-lane controllers supporting SR-IOV, + Four PCIe Gen 4.0 4-lane controllers. + Four serial ATA (SATA 3.0) controllers. + Two USB 3.0 controllers with integrated PHY + Two Enhanced secure digital host controllers + Two Controller Area Network (CAN) modules + Flexible Serial peripheral interface (FlexSPI) controller. + Three Serial peripheral interface (SPI) controllers. + Eight I2C Controllers. + Four PL011 UARTs supporting two 4-pin UART ports or four 2-pin UART ports. + General Purpose IO (GPIO) + Support for hardware virtualization and partitioning (ARM MMU-500) + Support for GIC (ARM GIC-500) + QorIQ platform Trust Architecture 3.0 + One Secure WatchDog timer and one Non-Secure Watchdog timer. + ARM Generic Timer + Two Flextimers + Debug supporting run control, data acquisition, high-speed trace, + performance/event monitoring + Thermal Monitor Unit (TMU) with +/- 2C accuracy + Support for Voltage ID (VID) for yield improvement + +LX2160A SoC has 2 more similar SoC personalities +1)LX2120A, few difference w.r.t. LX2160A: + a) Twelve 64-bit ARM v8 Cortex-A72 CPUs + +2)LX2080A, few difference w.r.t. LX2160A: + a) Eight 64-bit ARM v8 Cortex-A72 CPUs diff --git a/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch3_serdes.c b/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch3_serdes.c index bfd2868..a157c47 100644 --- a/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch3_serdes.c +++ b/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch3_serdes.c @@ -22,9 +22,18 @@ static u8 serdes3_prtcl_map[SERDES_PRCTL_COUNT]; #endif
#if defined(CONFIG_FSL_MC_ENET) && !defined(CONFIG_SPL_BUILD) +#ifdef CONFIG_ARCH_LX2160A +int xfi_dpmac[XFI14 + 1]; +int sgmii_dpmac[SGMII18 + 1]; +int a25gaui_dpmac[_25GE10 + 1]; +int xlaui_dpmac[_40GE2 + 1]; +int caui2_dpmac[_50GE2 + 1]; +int caui4_dpmac[_100GE2 + 1]; +#else int xfi_dpmac[XFI8 + 1]; int sgmii_dpmac[SGMII16 + 1]; #endif +#endif
__weak void wriop_init_dpmac_qsgmii(int sd, int lane_prtcl) { @@ -146,6 +155,32 @@ void serdes_init(u32 sd, u32 sd_addr, u32 rcwsr, u32 sd_prctl_mask, else { serdes_prtcl_map[lane_prtcl] = 1; #if defined(CONFIG_FSL_MC_ENET) && !defined(CONFIG_SPL_BUILD) +#ifdef CONFIG_ARCH_LX2160A + if (lane_prtcl >= XFI1 && lane_prtcl <= XFI14) + wriop_init_dpmac(sd, xfi_dpmac[lane_prtcl], + (int)lane_prtcl); + + if (lane_prtcl >= SGMII1 && lane_prtcl <= SGMII18) + wriop_init_dpmac(sd, sgmii_dpmac[lane_prtcl], + (int)lane_prtcl); + + if (lane_prtcl >= _25GE1 && lane_prtcl <= _25GE10) + wriop_init_dpmac(sd, a25gaui_dpmac[lane_prtcl], + (int)lane_prtcl); + + if (lane_prtcl >= _40GE1 && lane_prtcl <= _40GE2) + wriop_init_dpmac(sd, xlaui_dpmac[lane_prtcl], + (int)lane_prtcl); + + if (lane_prtcl >= _50GE1 && lane_prtcl <= _50GE2) + wriop_init_dpmac(sd, caui2_dpmac[lane_prtcl], + (int)lane_prtcl); + + if (lane_prtcl >= _100GE1 && lane_prtcl <= _100GE2) + wriop_init_dpmac(sd, caui4_dpmac[lane_prtcl], + (int)lane_prtcl); + +#else switch (lane_prtcl) { case QSGMII_A: case QSGMII_B: @@ -167,6 +202,7 @@ void serdes_init(u32 sd, u32 sd_addr, u32 rcwsr, u32 sd_prctl_mask, break; } #endif +#endif } }
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/lx2160a_serdes.c b/arch/arm/cpu/armv8/fsl-layerscape/lx2160a_serdes.c new file mode 100644 index 0000000..a04a370 --- /dev/null +++ b/arch/arm/cpu/armv8/fsl-layerscape/lx2160a_serdes.c @@ -0,0 +1,132 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018 NXP + */ + +#include <common.h> +#include <asm/arch/fsl_serdes.h> + +struct serdes_config { + u8 protocol; + u8 lanes[SRDS_MAX_LANES]; +}; + +static struct serdes_config serdes1_cfg_tbl[] = { + /* SerDes 1 */ + {0x01, {PCIE2, PCIE2, PCIE2, PCIE2, PCIE1, PCIE1, PCIE1, PCIE1 } }, + {0x02, {PCIE2, PCIE2, PCIE2, PCIE2, SGMII6, SGMII5, SGMII4, SGMII3 } }, + {0x03, {PCIE2, PCIE2, PCIE2, PCIE2, XFI6, XFI5, XFI4, + XFI3 } }, + {0x04, {SGMII10, SGMII9, SGMII8, SGMII7, SGMII6, SGMII5, SGMII4, + SGMII3 } }, + {0x05, {XFI10, XFI9, XFI8, XFI7, PCIE1, PCIE1, PCIE1, + PCIE1 } }, + {0x06, {SGMII10, SGMII9, SGMII8, SGMII7, SGMII6, SGMII5, XFI4, + XFI3 } }, + {0x07, {SGMII10, SGMII9, SGMII8, SGMII7, XFI6, XFI5, XFI4, + XFI3 } }, + {0x08, {XFI10, XFI9, XFI8, XFI7, XFI6, XFI5, XFI4, XFI3 } }, + {0x09, {SGMII10, SGMII9, SGMII8, PCIE2, SGMII6, SGMII5, SGMII4, + PCIE1 } }, + {0x0A, {XFI10, XFI9, XFI8, PCIE2, XFI6, XFI5, XFI4, PCIE1 } }, + {0x0B, {SGMII10, SGMII9, PCIE2, PCIE2, SGMII6, SGMII5, PCIE1, PCIE1 } }, + {0x0C, {SGMII10, SGMII9, PCIE2, PCIE2, PCIE1, PCIE1, PCIE1, PCIE1 } }, + {0x0D, {_100GE2, _100GE2, _100GE2, _100GE2, _100GE1, _100GE1, _100GE1, + _100GE1 } }, + {0x0E, {PCIE2, PCIE2, PCIE2, PCIE2, _100GE1, _100GE1, _100GE1, + _100GE1 } }, + {0x0F, {PCIE2, PCIE2, PCIE2, PCIE2, _50GE2, _50GE2, _50GE1, _50GE1 } }, + {0x10, {PCIE2, PCIE2, PCIE2, PCIE2, _25GE6, _25GE5, _50GE1, _50GE1 } }, + {0x11, {PCIE2, PCIE2, PCIE2, PCIE2, _25GE6, _25GE5, _25GE4, _25GE3 } }, + {0x12, {XFI10, XFI9, XFI8, XFI7, _25GE6, _25GE5, XFI4, + XFI3 } }, + {0x13, {_40GE2, _40GE2, _40GE2, _40GE2, _25GE6, _25GE5, XFI4, XFI3 } }, + {0x14, {_40GE2, _40GE2, _40GE2, _40GE2, _40GE1, _40GE1, _40GE1, + _40GE1 } }, + {0x15, {_25GE10, _25GE9, PCIE2, PCIE2, _25GE6, _25GE5, _25GE4, + _25GE3 } }, + {0x16, {XFI10, XFI9, PCIE2, PCIE2, XFI6, XFI5, XFI4, XFI3 } }, + {} +}; + +static struct serdes_config serdes2_cfg_tbl[] = { + /* SerDes 2 */ + {0x01, {PCIE3, PCIE3, SATA1, SATA2, PCIE4, PCIE4, PCIE4, PCIE4 } }, + {0x02, {PCIE3, PCIE3, PCIE3, PCIE3, PCIE3, PCIE3, PCIE3, PCIE3 } }, + {0x03, {PCIE3, PCIE3, PCIE3, PCIE3, PCIE4, PCIE4, PCIE4, PCIE4 } }, + {0x04, {PCIE3, PCIE3, PCIE3, PCIE3, PCIE4, PCIE4, SATA1, SATA2 } }, + {0x05, {PCIE3, PCIE3, PCIE3, PCIE3, SATA3, SATA4, SATA1, SATA2 } }, + {0x06, {PCIE3, PCIE3, PCIE3, PCIE3, SGMII15, SGMII16, XFI13, + XFI14 } }, + {0x07, {PCIE3, SGMII12, SGMII17, SGMII18, PCIE4, SGMII16, XFI13, + XFI14 } }, + {0x08, {NONE, NONE, SATA1, SATA2, SATA3, SATA4, XFI13, XFI14 } }, + {0x09, {SGMII11, SGMII12, SGMII17, SGMII18, SGMII15, SGMII16, SGMII13, + SGMII14} }, + {0x0A, {SGMII11, SGMII12, SGMII17, SGMII18, PCIE4, PCIE4, PCIE4, + PCIE4 } }, + {0x0B, {PCIE3, SGMII12, SGMII17, SGMII18, PCIE4, SGMII16, SGMII13, + SGMII14 } }, + {0x0C, {SGMII11, SGMII12, SGMII17, SGMII18, PCIE4, PCIE4, SATA1, + SATA2 } }, + {0x0D, {PCIE3, PCIE3, PCIE3, PCIE3, PCIE4, PCIE4, SGMII13, SGMII14 } }, + {0x0E, {PCIE3, PCIE3, SGMII17, SGMII18, PCIE4, PCIE4, SGMII13, + SGMII14 } }, + {} +}; + +static struct serdes_config serdes3_cfg_tbl[] = { + /* SerDes 3 */ + {0x02, {PCIE5, PCIE5, PCIE5, PCIE5, PCIE5, PCIE5, PCIE5, PCIE5 } }, + {0x03, {PCIE5, PCIE5, PCIE5, PCIE5, PCIE6, PCIE6, PCIE6, PCIE6 } }, + {} +}; + +static struct serdes_config *serdes_cfg_tbl[] = { + serdes1_cfg_tbl, + serdes2_cfg_tbl, + serdes3_cfg_tbl, +}; + +enum srds_prtcl serdes_get_prtcl(int serdes, int cfg, int lane) +{ + struct serdes_config *ptr; + + if (serdes >= ARRAY_SIZE(serdes_cfg_tbl)) + return 0; + + ptr = serdes_cfg_tbl[serdes]; + while (ptr->protocol) { + if (ptr->protocol == cfg) + return ptr->lanes[lane]; + ptr++; + } + + return 0; +} + +int is_serdes_prtcl_valid(int serdes, u32 prtcl) +{ + int i; + struct serdes_config *ptr; + + if (serdes >= ARRAY_SIZE(serdes_cfg_tbl)) + return 0; + + ptr = serdes_cfg_tbl[serdes]; + while (ptr->protocol) { + if (ptr->protocol == prtcl) + break; + ptr++; + } + + if (!ptr->protocol) + return 0; + + for (i = 0; i < SRDS_MAX_LANES; i++) { + if (ptr->lanes[i] != NONE) + return 1; + } + + return 0; +} diff --git a/arch/arm/dts/fsl-lx2160a.dtsi b/arch/arm/dts/fsl-lx2160a.dtsi new file mode 100644 index 0000000..db2c274 --- /dev/null +++ b/arch/arm/dts/fsl-lx2160a.dtsi @@ -0,0 +1,143 @@ +// SPDX-License-Identifier: GPL-2.0+ OR X11 +/* + * NXP lx2160a SOC common device tree source + * + * Copyright 2018 NXP + * + */ + +/ { + compatible = "fsl,lx2160a"; + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + memory@80000000 { + device_type = "memory"; + reg = <0x00000000 0x80000000 0 0x80000000>; + /* DRAM space - 1, size : 2 GB DRAM */ + }; + + sysclk: sysclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <100000000>; + clock-output-names = "sysclk"; + }; + + clockgen: clocking@1300000 { + compatible = "fsl,ls2080a-clockgen"; + reg = <0 0x1300000 0 0xa0000>; + #clock-cells = <2>; + clocks = <&sysclk>; + }; + + gic: interrupt-controller@6000000 { + compatible = "arm,gic-v3"; + reg = <0x0 0x06000000 0 0x10000>, /* GIC Dist */ + <0x0 0x06200000 0 0x100000>; /* GICR */ + #interrupt-cells = <3>; + interrupt-controller; + interrupts = <1 9 0x4>; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <1 13 0x8>, /* Physical Secure PPI, active-low */ + <1 14 0x8>, /* Physical NS PPI, active-low */ + <1 11 0x8>, /* Virtual PPI, active-low */ + <1 10 0x8>; /* Hypervisor PPI, active-low */ + }; + + uart0: serial@21c0000 { + compatible = "arm,pl011"; + reg = <0x0 0x21c0000 0x0 0x1000>; + clocks = <&clockgen 4 0>; + }; + + uart1: serial@21d0000 { + compatible = "arm,pl011"; + reg = <0x0 0x21d0000 0x0 0x1000>; + clocks = <&clockgen 4 0>; + }; + + uart2: serial@21e0000 { + compatible = "arm,pl011"; + reg = <0x0 0x21e0000 0x0 0x1000>; + clocks = <&clockgen 4 0>; + status = "disabled"; + }; + + uart3: serial@21f0000 { + compatible = "arm,pl011"; + reg = <0x0 0x21f0000 0x0 0x1000>; + clocks = <&clockgen 4 0>; + status = "disabled"; + }; + + esdhc0: esdhc@2140000 { + compatible = "fsl,esdhc"; + reg = <0x0 0x2140000 0x0 0x10000>; + interrupts = <0 28 0x4>; /* Level high type */ + clocks = <&clockgen 4 1>; + voltage-ranges = <1800 1800 3300 3300>; + sdhci,auto-cmd12; + little-endian; + bus-width = <4>; + status = "disabled"; + }; + + esdhc1: esdhc@2150000 { + compatible = "fsl,esdhc"; + reg = <0x0 0x2150000 0x0 0x10000>; + interrupts = <0 63 0x4>; /* Level high type */ + clocks = <&clockgen 4 1>; + voltage-ranges = <1800 1800 3300 3300>; + sdhci,auto-cmd12; + non-removable; + little-endian; + bus-width = <4>; + status = "disabled"; + }; + + dspi0: dspi@2100000 { + compatible = "fsl,vf610-dspi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2100000 0x0 0x10000>; + interrupts = <0 26 0x4>; /* Level high type */ + num-cs = <6>; + }; + + dspi1: dspi@2110000 { + compatible = "fsl,vf610-dspi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2110000 0x0 0x10000>; + interrupts = <0 240 0x4>; /* Level high type */ + num-cs = <6>; + }; + + dspi2: dspi@2120000 { + compatible = "fsl,vf610-dspi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2120000 0x0 0x10000>; + interrupts = <0 241 0x4>; /* Level high type */ + num-cs = <6>; + }; + + usb0: usb3@3100000 { + compatible = "fsl,layerscape-dwc3"; + reg = <0x0 0x3100000 0x0 0x10000>; + interrupts = <0 80 0x4>; /* Level high type */ + dr_mode = "host"; + }; + + usb1: usb3@3110000 { + compatible = "fsl,layerscape-dwc3"; + reg = <0x0 0x3110000 0x0 0x10000>; + interrupts = <0 81 0x4>; /* Level high type */ + dr_mode = "host"; + }; +}; diff --git a/arch/arm/include/asm/arch-fsl-layerscape/config.h b/arch/arm/include/asm/arch-fsl-layerscape/config.h index 8a05148..dbfad99 100644 --- a/arch/arm/include/asm/arch-fsl-layerscape/config.h +++ b/arch/arm/include/asm/arch-fsl-layerscape/config.h @@ -1,5 +1,6 @@ /* SPDX-License-Identifier: GPL-2.0+ */ /* + * Copyright 2018 NXP * Copyright 2015, Freescale Semiconductor */
@@ -176,6 +177,61 @@ #define SYS_FSL_OCRAM_SPACE_SIZE 0x00200000 /* 2M space */ #define CONFIG_SYS_FSL_OCRAM_SIZE 0x00020000 /* Real size 128K */
+/* LX2160A Soc Support */ +#elif defined(CONFIG_ARCH_LX2160A) +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_EARLY_INIT +#define SRDS_MAX_LANES 8 +#ifndef L1_CACHE_BYTES +#define L1_CACHE_SHIFT 6 +#define L1_CACHE_BYTES BIT(L1_CACHE_SHIFT) +#endif +#define CONFIG_SYS_FSL_CORES_PER_CLUSTER 2 +#define CONFIG_SYS_FSL_CLUSTER_CLOCKS { 1, 1, 1, 1, 4, 4, 4, 4 } +#define CONFIG_SYS_FSL_NUM_CC_PLLS 4 + +#define CONFIG_SYS_PAGE_SIZE 0x10000 + +#define CONFIG_SYS_FSL_OCRAM_BASE 0x18000000 /* initial RAM */ +#define SYS_FSL_OCRAM_SPACE_SIZE 0x00200000 /* 2M space */ +#define CONFIG_SYS_FSL_OCRAM_SIZE 0x00040000 /* Real size 256K */ + +/* DDR */ +#define CONFIG_SYS_DDR_BLOCK1_SIZE ((phys_size_t)2 << 30) +#define CONFIG_MAX_MEM_MAPPED CONFIG_SYS_DDR_BLOCK1_SIZE + +#define CONFIG_SYS_FSL_CCSR_GUR_LE +#define CONFIG_SYS_FSL_CCSR_SCFG_LE +#define CONFIG_SYS_FSL_ESDHC_LE +#define CONFIG_SYS_FSL_PEX_LUT_LE + +#define CONFIG_SYS_MEMAC_LITTLE_ENDIAN + +/* Generic Interrupt Controller Definitions */ +#define GICD_BASE 0x06000000 +#define GICR_BASE 0x06200000 + +/* SMMU Definitions */ +#define SMMU_BASE 0x05000000 /* GR0 Base */ + +/* SFP */ +#define CONFIG_SYS_FSL_SFP_VER_3_4 +#define CONFIG_SYS_FSL_SFP_LE +#define CONFIG_SYS_FSL_SRK_LE + +/* Security Monitor */ +#define CONFIG_SYS_FSL_SEC_MON_LE + +/* Secure Boot */ +#define CONFIG_ESBC_HDR_LS + +/* DCFG - GUR */ +#define CONFIG_SYS_FSL_CCSR_GUR_LE + +#define CONFIG_SYS_FSL_MAX_NUM_OF_SEC 1 + +/* end LX2160A Soc Support */ + #elif defined(CONFIG_FSL_LSCH2) #define CONFIG_SYS_FSL_OCRAM_BASE 0x10000000 /* initial RAM */ #define SYS_FSL_OCRAM_SPACE_SIZE 0x00200000 /* 2M space */ diff --git a/arch/arm/include/asm/arch-fsl-layerscape/cpu.h b/arch/arm/include/asm/arch-fsl-layerscape/cpu.h index ed1a21d..271d077 100644 --- a/arch/arm/include/asm/arch-fsl-layerscape/cpu.h +++ b/arch/arm/include/asm/arch-fsl-layerscape/cpu.h @@ -27,6 +27,9 @@ static struct cpu_type cpu_type_list[] = { CPU_TYPE_ENTRY(LS1084A, LS1084A, 8), CPU_TYPE_ENTRY(LS1048A, LS1048A, 4), CPU_TYPE_ENTRY(LS1044A, LS1044A, 4), + CPU_TYPE_ENTRY(LX2160A, LX2160A, 16), + CPU_TYPE_ENTRY(LX2120A, LX2120A, 12), + CPU_TYPE_ENTRY(LX2080A, LX2080A, 8), };
#ifndef CONFIG_SYS_DCACHE_OFF diff --git a/arch/arm/include/asm/arch-fsl-layerscape/fsl_serdes.h b/arch/arm/include/asm/arch-fsl-layerscape/fsl_serdes.h index bec35e8..8dbabd7 100644 --- a/arch/arm/include/asm/arch-fsl-layerscape/fsl_serdes.h +++ b/arch/arm/include/asm/arch-fsl-layerscape/fsl_serdes.h @@ -20,8 +20,12 @@ enum srds_prtcl { PCIE2, PCIE3, PCIE4, + PCIE5, + PCIE6, SATA1, SATA2, + SATA3, + SATA4, XAUI1, XAUI2, XFI1, @@ -32,6 +36,12 @@ enum srds_prtcl { XFI6, XFI7, XFI8, + XFI9, + XFI10, + XFI11, + XFI12, + XFI13, + XFI14, SGMII1, SGMII2, SGMII3, @@ -48,10 +58,28 @@ enum srds_prtcl { SGMII14, SGMII15, SGMII16, + SGMII17, + SGMII18, QSGMII_A, QSGMII_B, QSGMII_C, QSGMII_D, + _25GE1, + _25GE2, + _25GE3, + _25GE4, + _25GE5, + _25GE6, + _25GE7, + _25GE8, + _25GE9, + _25GE10, + _40GE1, + _40GE2, + _50GE1, + _50GE2, + _100GE1, + _100GE2, SERDES_PRCTL_COUNT };
diff --git a/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h b/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h index 8740dd7..56b2deb 100644 --- a/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h +++ b/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h @@ -2,7 +2,7 @@ /* * LayerScape Internal Memory Map * - * Copyright (C) 2017 NXP Semiconductors + * Copyright 2017-2018 NXP * Copyright 2014 Freescale Semiconductor, Inc. */
@@ -15,7 +15,11 @@ #define CONFIG_SYS_FSL_DDR3_ADDR 0x08210000 #define CONFIG_SYS_FSL_GUTS_ADDR (CONFIG_SYS_IMMR + 0x00E00000) #define CONFIG_SYS_FSL_PMU_ADDR (CONFIG_SYS_IMMR + 0x00E30000) +#ifdef CONFIG_ARCH_LX2160A +#define CONFIG_SYS_FSL_RST_ADDR (CONFIG_SYS_IMMR + 0x00e88180) +#else #define CONFIG_SYS_FSL_RST_ADDR (CONFIG_SYS_IMMR + 0x00E60000) +#endif #define CONFIG_SYS_FSL_CH3_CLK_GRPA_ADDR (CONFIG_SYS_IMMR + 0x00300000) #define CONFIG_SYS_FSL_CH3_CLK_GRPB_ADDR (CONFIG_SYS_IMMR + 0x00310000) #define CONFIG_SYS_FSL_CH3_CLK_CTRL_ADDR (CONFIG_SYS_IMMR + 0x00370000) @@ -275,6 +279,28 @@ struct ccsr_gur { #define FSL_CHASSIS3_SRDS2_PRTCL_SHIFT FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_SHIFT #define FSL_CHASSIS3_SRDS1_REGSR 29 #define FSL_CHASSIS3_SRDS2_REGSR 29 +#elif defined(CONFIG_ARCH_LX2160A) +#define FSL_CHASSIS3_EC1_REGSR 27 +#define FSL_CHASSIS3_EC2_REGSR 27 +#define FSL_CHASSIS3_EC1_REGSR_PRTCL_MASK 0x00000003 +#define FSL_CHASSIS3_EC1_REGSR_PRTCL_SHIFT 0 +#define FSL_CHASSIS3_EC2_REGSR_PRTCL_MASK 0x00000007 +#define FSL_CHASSIS3_EC2_REGSR_PRTCL_SHIFT 2 +#define FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_MASK 0x001F0000 +#define FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_SHIFT 16 +#define FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_MASK 0x03E00000 +#define FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_SHIFT 21 +#define FSL_CHASSIS3_RCWSR28_SRDS3_PRTCL_MASK 0x7C000000 +#define FSL_CHASSIS3_RCWSR28_SRDS3_PRTCL_SHIFT 26 +#define FSL_CHASSIS3_SRDS1_PRTCL_MASK FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_MASK +#define FSL_CHASSIS3_SRDS1_PRTCL_SHIFT FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_SHIFT +#define FSL_CHASSIS3_SRDS2_PRTCL_MASK FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_MASK +#define FSL_CHASSIS3_SRDS2_PRTCL_SHIFT FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_SHIFT +#define FSL_CHASSIS3_SRDS3_PRTCL_MASK FSL_CHASSIS3_RCWSR28_SRDS3_PRTCL_MASK +#define FSL_CHASSIS3_SRDS3_PRTCL_SHIFT FSL_CHASSIS3_RCWSR28_SRDS3_PRTCL_SHIFT +#define FSL_CHASSIS3_SRDS1_REGSR 29 +#define FSL_CHASSIS3_SRDS2_REGSR 29 +#define FSL_CHASSIS3_SRDS3_REGSR 29 #elif defined(CONFIG_ARCH_LS1088A) #define FSL_CHASSIS3_EC1_REGSR 26 #define FSL_CHASSIS3_EC2_REGSR 26 diff --git a/arch/arm/include/asm/arch-fsl-layerscape/soc.h b/arch/arm/include/asm/arch-fsl-layerscape/soc.h index 61b6e4b..3de7c56 100644 --- a/arch/arm/include/asm/arch-fsl-layerscape/soc.h +++ b/arch/arm/include/asm/arch-fsl-layerscape/soc.h @@ -1,6 +1,6 @@ /* SPDX-License-Identifier: GPL-2.0+ */ /* - * Copyright 2017 NXP + * Copyright 2017-2018 NXP * Copyright 2015 Freescale Semiconductor */
@@ -74,12 +74,18 @@ struct cpu_type { #define SVR_LS2044A 0x870930 #define SVR_LS2081A 0x870918 #define SVR_LS2041A 0x870914 +#define SVR_LX2160A 0x873601 +#define SVR_LX2120A 0x873621 +#define SVR_LX2080A 0x873603
#define SVR_MAJ(svr) (((svr) >> 4) & 0xf) #define SVR_MIN(svr) (((svr) >> 0) & 0xf) #define SVR_REV(svr) (((svr) >> 0) & 0xff) #define SVR_SOC_VER(svr) (((svr) >> 8) & SVR_WO_E) #define IS_E_PROCESSOR(svr) (!((svr >> 8) & 0x1)) +#ifdef CONFIG_ARCH_LX2160A +#define IS_C_PROCESSOR(svr) (!((svr >> 12) & 0x1)) +#endif #define IS_SVR_REV(svr, maj, min) \ ((SVR_MAJ(svr) == (maj)) && (SVR_MIN(svr) == (min))) #define SVR_DEV(svr) ((svr) >> 8) diff --git a/arch/arm/include/asm/arch-fsl-layerscape/stream_id_lsch3.h b/arch/arm/include/asm/arch-fsl-layerscape/stream_id_lsch3.h index afea9b8..227b438 100644 --- a/arch/arm/include/asm/arch-fsl-layerscape/stream_id_lsch3.h +++ b/arch/arm/include/asm/arch-fsl-layerscape/stream_id_lsch3.h @@ -1,5 +1,6 @@ /* SPDX-License-Identifier: GPL-2.0+ */ /* + * Copyright 2018 NXP * Copyright 2014 Freescale Semiconductor, Inc. * */ @@ -66,11 +67,11 @@ #define FSL_SDMMC_STREAM_ID 3 #define FSL_SATA1_STREAM_ID 4
-#if defined(CONFIG_ARCH_LS2080A) +#if defined(CONFIG_ARCH_LS2080A) || defined(CONFIG_ARCH_LX2160A) #define FSL_SATA2_STREAM_ID 5 #endif
-#if defined(CONFIG_ARCH_LS2080A) +#if defined(CONFIG_ARCH_LS2080A) || defined(CONFIG_ARCH_LX2160A) #define FSL_DMA_STREAM_ID 6 #elif defined(CONFIG_ARCH_LS1088A) #define FSL_DMA_STREAM_ID 5 @@ -79,6 +80,10 @@ /* PCI - programmed in PEXn_LUT */ #define FSL_PEX_STREAM_ID_START 7
+#ifdef CONFIG_ARCH_LX2160A +#define FSL_PEX_STREAM_ID_NUM (0x100) +#endif + #if defined(CONFIG_ARCH_LS2080A) #define FSL_PEX_STREAM_ID_END 22 #elif defined(CONFIG_ARCH_LS1088A) diff --git a/drivers/net/ldpaa_eth/Makefile b/drivers/net/ldpaa_eth/Makefile index 477ee4f..8e00f17 100644 --- a/drivers/net/ldpaa_eth/Makefile +++ b/drivers/net/ldpaa_eth/Makefile @@ -1,8 +1,9 @@ # SPDX-License-Identifier: GPL-2.0+ -# +# Copyright 2018 NXP # Copyright 2014 Freescale Semiconductor, Inc.
obj-y += ldpaa_wriop.o obj-y += ldpaa_eth.o obj-$(CONFIG_ARCH_LS2080A) += ls2080a.o obj-$(CONFIG_ARCH_LS1088A) += ls1088a.o +obj-$(CONFIG_ARCH_LX2160A) += lx2160a.o diff --git a/drivers/net/ldpaa_eth/lx2160a.c b/drivers/net/ldpaa_eth/lx2160a.c new file mode 100644 index 0000000..7dd46c0 --- /dev/null +++ b/drivers/net/ldpaa_eth/lx2160a.c @@ -0,0 +1,107 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018 NXP + */ +#include <common.h> +#include <phy.h> +#include <fsl-mc/ldpaa_wriop.h> +#include <asm/io.h> +#include <asm/arch/fsl_serdes.h> +#include <asm/arch/soc.h> + +u32 dpmac_to_devdisr[] = { + [WRIOP1_DPMAC1] = FSL_CHASSIS3_DEVDISR2_DPMAC1, + [WRIOP1_DPMAC2] = FSL_CHASSIS3_DEVDISR2_DPMAC2, + [WRIOP1_DPMAC3] = FSL_CHASSIS3_DEVDISR2_DPMAC3, + [WRIOP1_DPMAC4] = FSL_CHASSIS3_DEVDISR2_DPMAC4, + [WRIOP1_DPMAC5] = FSL_CHASSIS3_DEVDISR2_DPMAC5, + [WRIOP1_DPMAC6] = FSL_CHASSIS3_DEVDISR2_DPMAC6, + [WRIOP1_DPMAC7] = FSL_CHASSIS3_DEVDISR2_DPMAC7, + [WRIOP1_DPMAC8] = FSL_CHASSIS3_DEVDISR2_DPMAC8, + [WRIOP1_DPMAC9] = FSL_CHASSIS3_DEVDISR2_DPMAC9, + [WRIOP1_DPMAC10] = FSL_CHASSIS3_DEVDISR2_DPMAC10, + [WRIOP1_DPMAC11] = FSL_CHASSIS3_DEVDISR2_DPMAC11, + [WRIOP1_DPMAC12] = FSL_CHASSIS3_DEVDISR2_DPMAC12, + [WRIOP1_DPMAC13] = FSL_CHASSIS3_DEVDISR2_DPMAC13, + [WRIOP1_DPMAC14] = FSL_CHASSIS3_DEVDISR2_DPMAC14, + [WRIOP1_DPMAC15] = FSL_CHASSIS3_DEVDISR2_DPMAC15, + [WRIOP1_DPMAC16] = FSL_CHASSIS3_DEVDISR2_DPMAC16, + [WRIOP1_DPMAC17] = FSL_CHASSIS3_DEVDISR2_DPMAC17, + [WRIOP1_DPMAC18] = FSL_CHASSIS3_DEVDISR2_DPMAC18, +}; + +static int is_device_disabled(int dpmac_id) +{ + struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR; + u32 devdisr2 = in_le32(&gur->devdisr2); + + return dpmac_to_devdisr[dpmac_id] & devdisr2; +} + +void wriop_dpmac_disable(int dpmac_id) +{ + struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR; + + setbits_le32(&gur->devdisr2, dpmac_to_devdisr[dpmac_id]); +} + +void wriop_dpmac_enable(int dpmac_id) +{ + struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR; + + clrbits_le32(&gur->devdisr2, dpmac_to_devdisr[dpmac_id]); +} + +phy_interface_t wriop_dpmac_enet_if(int dpmac_id, int lane_prtcl) +{ + enum srds_prtcl; + + if (is_device_disabled(dpmac_id + 1)) + return PHY_INTERFACE_MODE_NONE; + + if (lane_prtcl >= SGMII1 && lane_prtcl <= SGMII18) + return PHY_INTERFACE_MODE_SGMII; + + if (lane_prtcl >= XFI1 && lane_prtcl <= XFI14) + return PHY_INTERFACE_MODE_XGMII; + + if (lane_prtcl >= _25GE1 && lane_prtcl <= _25GE10) + return PHY_INTERFACE_MODE_25G_AUI; + + if (lane_prtcl >= _40GE1 && lane_prtcl <= _40GE2) + return PHY_INTERFACE_MODE_XLAUI; + + if (lane_prtcl >= _50GE1 && lane_prtcl <= _50GE2) + return PHY_INTERFACE_MODE_CAUI2; + + if (lane_prtcl >= _100GE1 && lane_prtcl <= _100GE2) + return PHY_INTERFACE_MODE_CAUI4; + + return PHY_INTERFACE_MODE_NONE; +} + +#ifdef CONFIG_SYS_FSL_HAS_RGMII +void fsl_rgmii_init(void) +{ + struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR); + u32 ec; + +#ifdef CONFIG_SYS_FSL_EC1 + ec = gur_in32(&gur->rcwsr[FSL_CHASSIS3_EC1_REGSR - 1]) + & FSL_CHASSIS3_EC1_REGSR_PRTCL_MASK; + ec >>= FSL_CHASSIS3_EC1_REGSR_PRTCL_SHIFT; + + if (!ec) + wriop_init_dpmac_enet_if(17, PHY_INTERFACE_MODE_RGMII_ID); +#endif + +#ifdef CONFIG_SYS_FSL_EC2 + ec = gur_in32(&gur->rcwsr[FSL_CHASSIS3_EC2_REGSR - 1]) + & FSL_CHASSIS3_EC2_REGSR_PRTCL_MASK; + ec >>= FSL_CHASSIS3_EC2_REGSR_PRTCL_SHIFT; + + if (!ec) + wriop_init_dpmac_enet_if(18, PHY_INTERFACE_MODE_RGMII_ID); +#endif +} +#endif