Not that the Kconfig conversion of a lot of variables is done, we can factor out the common include files for the keymile boards again (which now contain hardly any #ifdef logic at all).
Signed-off-by: Mario Six mario.six@gdsys.cc
---
v2 -> v3: New in v3
--- include/configs/km/km-mpc8309.h | 137 +++++++++++++ include/configs/km/km-mpc832x.h | 91 +++++++++ include/configs/km/km-mpc8360.h | 91 +++++++++ include/configs/km/km-mpc83xx.h | 160 +++++++++++++++ include/configs/kmcoge5ne.h | 262 +------------------------ include/configs/kmeter1.h | 258 +------------------------ include/configs/kmopti2.h | 286 +-------------------------- include/configs/kmsupx5.h | 277 +------------------------- include/configs/kmtegr1.h | 331 +------------------------------ include/configs/kmtepr2.h | 278 +------------------------- include/configs/kmvect1.h | 332 +------------------------------- include/configs/suvd3.h | 278 +------------------------- include/configs/tuge1.h | 277 +------------------------- include/configs/tuxx1.h | 278 +------------------------- 14 files changed, 500 insertions(+), 2836 deletions(-) create mode 100644 include/configs/km/km-mpc8309.h create mode 100644 include/configs/km/km-mpc832x.h create mode 100644 include/configs/km/km-mpc8360.h create mode 100644 include/configs/km/km-mpc83xx.h
diff --git a/include/configs/km/km-mpc8309.h b/include/configs/km/km-mpc8309.h new file mode 100644 index 00000000000..e89b7af0610 --- /dev/null +++ b/include/configs/km/km-mpc8309.h @@ -0,0 +1,137 @@ +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 family */ +#define CONFIG_QE 1 /* Has QE */ + +#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" + +/* + * System Clock Setup + */ +#define CONFIG_83XX_CLKIN 66000000 +#define CONFIG_SYS_CLK_FREQ 66000000 +#define CONFIG_83XX_PCICLK 66000000 + +/* QE microcode/firmware address */ +#define CONFIG_SYS_QE_FMAN_FW_IN_NOR +/* between the u-boot partition and env */ +#ifndef CONFIG_SYS_QE_FW_ADDR +#define CONFIG_SYS_QE_FW_ADDR 0xF00C0000 +#endif + +/* + * System IO Config + */ +/* 0x14000180 SICR_1 */ +#define CONFIG_SYS_SICRL (0 \ + | SICR_1_UART1_UART1RTS \ + | SICR_1_I2C_CKSTOP \ + | SICR_1_IRQ_A_IRQ \ + | SICR_1_IRQ_B_IRQ \ + | SICR_1_GPIO_A_GPIO \ + | SICR_1_GPIO_B_GPIO \ + | SICR_1_GPIO_C_GPIO \ + | SICR_1_GPIO_D_GPIO \ + | SICR_1_GPIO_E_GPIO \ + | SICR_1_GPIO_F_GPIO \ + | SICR_1_USB_A_UART2S \ + | SICR_1_USB_B_UART2RTS \ + | SICR_1_FEC1_FEC1 \ + | SICR_1_FEC2_FEC2 \ + ) + +/* 0x00080400 SICR_2 */ +#define CONFIG_SYS_SICRH (0 \ + | SICR_2_FEC3_FEC3 \ + | SICR_2_HDLC1_A_HDLC1 \ + | SICR_2_ELBC_A_LA \ + | SICR_2_ELBC_B_LCLK \ + | SICR_2_HDLC2_A_HDLC2 \ + | SICR_2_USB_D_GPIO \ + | SICR_2_PCI_PCI \ + | SICR_2_HDLC1_B_HDLC1 \ + | SICR_2_HDLC1_C_HDLC1 \ + | SICR_2_HDLC2_B_GPIO \ + | SICR_2_HDLC2_C_HDLC2 \ + | SICR_2_QUIESCE_B \ + ) + +/* GPR_1 */ +#define CONFIG_SYS_GPR1 0x50008060 + +#define CONFIG_SYS_GP1DIR 0x00000000 +#define CONFIG_SYS_GP1ODR 0x00000000 +#define CONFIG_SYS_GP2DIR 0xFF000000 +#define CONFIG_SYS_GP2ODR 0x00000000 + +#define CONFIG_SYS_DDRCDR (\ + DDRCDR_EN | \ + DDRCDR_PZ_MAXZ | \ + DDRCDR_NZ_MAXZ | \ + DDRCDR_M_ODR) + +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f +#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \ + SDRAM_CFG_32_BE | \ + SDRAM_CFG_SREN | \ + SDRAM_CFG_HSE) + +#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 +#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) +#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ + (0x200 << SDRAM_INTERVAL_REFINT_SHIFT)) + +#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \ + CSCONFIG_ODT_RD_NEVER | \ + CSCONFIG_ODT_WR_ONLY_CURRENT | \ + CSCONFIG_ROW_BIT_13 | \ + CSCONFIG_COL_BIT_10) + +#define CONFIG_SYS_DDR_MODE 0x47860242 +#define CONFIG_SYS_DDR_MODE2 0x8080c000 + +#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ + (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ + (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ + (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ + (0 << TIMING_CFG0_WWT_SHIFT) | \ + (0 << TIMING_CFG0_RRT_SHIFT) | \ + (0 << TIMING_CFG0_WRT_SHIFT) | \ + (0 << TIMING_CFG0_RWT_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \ + (2 << TIMING_CFG1_WRTORD_SHIFT) | \ + (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ + (3 << TIMING_CFG1_WRREC_SHIFT) | \ + (7 << TIMING_CFG1_REFREC_SHIFT) | \ + (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ + (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ + (3 << TIMING_CFG1_PRETOACT_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ + (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ + (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ + (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ + (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ + (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ + (5 << TIMING_CFG2_CPO_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_3 0x00000000 + +#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000 +#define CONFIG_SYS_KMBEC_FPGA_SIZE 128 + +/* EEprom support */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 + +/* ethernet port connected to piggy (UEC2) */ +#define CONFIG_HAS_ETH1 +#define CONFIG_UEC_ETH2 +#define CONFIG_SYS_UEC2_UCC_NUM 2 /* UCC3 */ +#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ +#define CONFIG_SYS_UEC2_TX_CLK QE_CLK12 +#define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH +#define CONFIG_SYS_UEC2_PHY_ADDR 0 +#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII +#define CONFIG_SYS_UEC2_INTERFACE_SPEED 100 diff --git a/include/configs/km/km-mpc832x.h b/include/configs/km/km-mpc832x.h new file mode 100644 index 00000000000..3c2173d3642 --- /dev/null +++ b/include/configs/km/km-mpc832x.h @@ -0,0 +1,91 @@ +/* + * High Level Configuration Options + */ +#define CONFIG_QE /* Has QE */ +#define CONFIG_KM8321 /* Keymile PBEC8321 board specific */ + +/* + * System Clock Setup + */ +#define CONFIG_83XX_CLKIN 66000000 +#define CONFIG_SYS_CLK_FREQ 66000000 +#define CONFIG_83XX_PCICLK 66000000 + +/* + * QE UEC ethernet configuration + */ +#define CONFIG_UEC_ETH1 /* GETH1 */ +#define UEC_VERBOSE_DEBUG 1 + +#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */ +#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ +#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17 +#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH +#define CONFIG_SYS_UEC1_PHY_ADDR 0 +#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII +#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 + +/* + * System IO Config + */ +#define CONFIG_SYS_SICRL SICRL_IRQ_CKS + +#define CONFIG_SYS_DDRCDR (\ + DDRCDR_EN | \ + DDRCDR_PZ_MAXZ | \ + DDRCDR_NZ_MAXZ | \ + DDRCDR_M_ODR) + +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f +#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \ + SDRAM_CFG_32_BE | \ + SDRAM_CFG_SREN | \ + SDRAM_CFG_HSE) + +#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 +#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) +#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ + (0x200 << SDRAM_INTERVAL_REFINT_SHIFT)) + +#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \ + CSCONFIG_ODT_WR_CFG | \ + CSCONFIG_ROW_BIT_13 | \ + CSCONFIG_COL_BIT_10) + +#define CONFIG_SYS_DDR_MODE 0x47860242 +#define CONFIG_SYS_DDR_MODE2 0x8080c000 + +#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ + (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ + (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ + (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ + (0 << TIMING_CFG0_WWT_SHIFT) | \ + (0 << TIMING_CFG0_RRT_SHIFT) | \ + (0 << TIMING_CFG0_WRT_SHIFT) | \ + (0 << TIMING_CFG0_RWT_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \ + (2 << TIMING_CFG1_WRTORD_SHIFT) | \ + (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ + (3 << TIMING_CFG1_WRREC_SHIFT) | \ + (7 << TIMING_CFG1_REFREC_SHIFT) | \ + (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ + (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ + (3 << TIMING_CFG1_PRETOACT_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ + (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ + (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ + (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ + (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ + (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ + (5 << TIMING_CFG2_CPO_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_3 0x00000000 + +#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000 +#define CONFIG_SYS_KMBEC_FPGA_SIZE 128 + +/* EEprom support */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 + diff --git a/include/configs/km/km-mpc8360.h b/include/configs/km/km-mpc8360.h new file mode 100644 index 00000000000..8f26e059e98 --- /dev/null +++ b/include/configs/km/km-mpc8360.h @@ -0,0 +1,91 @@ +/* KMBEC FPGA (PRIO) */ +#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000 +#define CONFIG_SYS_KMBEC_FPGA_SIZE 64 + +/* + * High Level Configuration Options + */ +#define CONFIG_QE /* Has QE */ + +/* + * QE UEC ethernet configuration + */ +#define CONFIG_UEC_ETH1 /* GETH1 */ +#define UEC_VERBOSE_DEBUG 1 + +#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */ +#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ +#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17 +#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH +#define CONFIG_SYS_UEC1_PHY_ADDR 0 +#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII +#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 + +/* + * System IO Setup + */ +#define CONFIG_SYS_SICRH (SICRH_UC1EOBI | SICRH_UC2E1OBI) + +/** + * DDR RAM settings + */ +#define CONFIG_SYS_DDR_SDRAM_CFG (\ + SDRAM_CFG_SDRAM_TYPE_DDR2 | \ + SDRAM_CFG_SREN | \ + SDRAM_CFG_HSE) + +#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 + +#define CONFIG_SYS_DDR_CLK_CNTL (\ + DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) + +#define CONFIG_SYS_DDR_INTERVAL (\ + (0x080 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ + (0x203 << SDRAM_INTERVAL_REFINT_SHIFT)) + +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f + +#define CONFIG_SYS_DDRCDR (\ + DDRCDR_EN | \ + DDRCDR_Q_DRN) +#define CONFIG_SYS_DDR_MODE 0x47860452 +#define CONFIG_SYS_DDR_MODE2 0x8080c000 + +#define CONFIG_SYS_DDR_TIMING_0 (\ + (2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ + (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ + (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ + (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ + (0 << TIMING_CFG0_WWT_SHIFT) | \ + (0 << TIMING_CFG0_RRT_SHIFT) | \ + (0 << TIMING_CFG0_WRT_SHIFT) | \ + (0 << TIMING_CFG0_RWT_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_50) | \ + (2 << TIMING_CFG1_WRTORD_SHIFT) | \ + (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ + (3 << TIMING_CFG1_WRREC_SHIFT) | \ + (7 << TIMING_CFG1_REFREC_SHIFT) | \ + (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ + (8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ + (3 << TIMING_CFG1_PRETOACT_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_2 (\ + (0xa << TIMING_CFG2_FOUR_ACT_SHIFT) | \ + (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ + (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ + (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ + (4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ + (5 << TIMING_CFG2_CPO_SHIFT) | \ + (0 << TIMING_CFG2_ADD_LAT_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_3 0x00000000 + +/* EEprom support */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 + +/* + * PAXE on the local bus CS3 + */ +#define CONFIG_SYS_PAXE_BASE 0xA0000000 +#define CONFIG_SYS_PAXE_SIZE 256 diff --git a/include/configs/km/km-mpc83xx.h b/include/configs/km/km-mpc83xx.h new file mode 100644 index 00000000000..455e5236deb --- /dev/null +++ b/include/configs/km/km-mpc83xx.h @@ -0,0 +1,160 @@ +/* + * Internal Definitions + */ +#define BOOTFLASH_START 0xF0000000 + +#define CONFIG_KM_CONSOLE_TTY "ttyS0" + +/* + * DDR Setup + */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */ +#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */ + +#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ + DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) + +#define CFG_83XX_DDR_USES_CS0 + +/* + * Manually set up DDR parameters + */ +#define CONFIG_DDR_II +#define CONFIG_SYS_DDR_SIZE 2048 /* MB */ + +/* + * The reserved memory + */ +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ +#define CONFIG_SYS_FLASH_BASE 0xF0000000 + +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +#define CONFIG_SYS_RAMBOOT +#endif + +/* Reserve 768 kB for Mon */ +#define CONFIG_SYS_MONITOR_LEN (768 * 1024) + +/* + * Initial RAM Base Address Setup + */ +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) +/* + * Init Local Bus Memory Controller: + * + * Bank Bus Machine PortSz Size Device + * ---- --- ------- ------ ----- ------ + * 0 Local GPCM 16 bit 256MB FLASH + * 1 Local GPCM 8 bit 128MB GPIO/PIGGY + * + */ + +/* + * FLASH on the Local Bus + */ +#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } + +/* + * Serial Port + */ +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_NUM_I2C_BUSES 4 +#define CONFIG_SYS_I2C_MAX_HOPS 1 +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 200000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 200000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \ + {1, {I2C_NULL_HOP} } } + +#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/ + +#if defined(CONFIG_CMD_NAND) +#define CONFIG_NAND_KMETER1 +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE +#endif + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) + +/* + * Environment + */ + +#ifndef CONFIG_SYS_RAMBOOT +#ifndef CONFIG_ENV_ADDR +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ + CONFIG_SYS_MONITOR_LEN) +#endif +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ +#ifndef CONFIG_ENV_OFFSET +#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN) +#endif + +/* Address and size of Redundant Environment Sector */ +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ + CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) + +#else /* CFG_SYS_RAMBOOT */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) +#define CONFIG_ENV_SIZE 0x2000 +#endif /* CFG_SYS_RAMBOOT */ + +/* + * Environment Configuration + */ +#define CONFIG_ENV_OVERWRITE +#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ +#define CONFIG_KM_DEF_ENV "km-common=empty\0" +#endif + +#ifndef CONFIG_KM_DEF_ARCH +#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" +#endif + +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_KM_DEF_ENV \ + CONFIG_KM_DEF_ARCH \ + "newenv=" \ + "prot off " __stringify(CONFIG_ENV_ADDR) " +0x40000 && " \ + "era " __stringify(CONFIG_ENV_ADDR) " +0x40000\0" \ + "unlock=yes\0" \ + "" + +#if defined(CONFIG_UEC_ETH) +#define CONFIG_HAS_ETH0 +#endif + +/* + * QE UEC ethernet configuration + */ +#define CONFIG_UEC_ETH +#define CONFIG_ETHPRIME "UEC0" diff --git a/include/configs/kmcoge5ne.h b/include/configs/kmcoge5ne.h index 720d28d61a0..a041a3ece52 100644 --- a/include/configs/kmcoge5ne.h +++ b/include/configs/kmcoge5ne.h @@ -8,10 +8,6 @@ #ifndef __CONFIG_H #define __CONFIG_H
-/* KMBEC FPGA (PRIO) */ -#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000 -#define CONFIG_SYS_KMBEC_FPGA_SIZE 64 - #define CONFIG_HOSTNAME "kmcoge5ne" #define CONFIG_KM_BOARD_NAME "kmcoge5ne" #define CONFIG_KM_DEF_NETDEV "netdev=eth1\0" @@ -24,14 +20,11 @@ #define CONFIG_KM_UBI_PARTITION_NAME_BOOT "ubi0" #define CONFIG_KM_UBI_PARTITION_NAME_APP "ubi1"
-/* - * High Level Configuration Options - */ -#define CONFIG_QE /* Has QE */ - /* include common defines/options for all Keymile boards */ #include "km/keymile-common.h" #include "km/km-powerpc.h" +#include "km/km-mpc83xx.h" +#include "km/km-mpc8360.h"
/* * System Clock Setup @@ -40,201 +33,6 @@ #define CONFIG_SYS_CLK_FREQ 66000000 #define CONFIG_83XX_PCICLK 66000000
-/* - * DDR Setup - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */ -#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */ - -#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ - DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) - -#define CFG_83XX_DDR_USES_CS0 - -/* - * Manually set up DDR parameters - */ -#define CONFIG_DDR_II -#define CONFIG_SYS_DDR_SIZE 2048 /* MB */ - -/* - * The reserved memory - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#define CONFIG_SYS_FLASH_BASE 0xF0000000 - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#endif - -/* Reserve 768 kB for Mon */ -#define CONFIG_SYS_MONITOR_LEN (768 * 1024) - -/* - * Initial RAM Base Address Setup - */ -#define CONFIG_SYS_INIT_RAM_LOCK -#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) - -/* - * Init Local Bus Memory Controller: - * - * Bank Bus Machine PortSz Size Device - * ---- --- ------- ------ ----- ------ - * 0 Local GPCM 16 bit 256MB FLASH - * 1 Local GPCM 8 bit 128MB GPIO/PIGGY - * - */ -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */ - - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } - -/* - * PRIO1/PIGGY on the local bus CS1 - */ - - -/* - * Serial Port - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) - -/* - * QE UEC ethernet configuration - */ -#define CONFIG_UEC_ETH -#define CONFIG_ETHPRIME "UEC0" - -#define CONFIG_UEC_ETH1 /* GETH1 */ -#define UEC_VERBOSE_DEBUG 1 - -#ifdef CONFIG_UEC_ETH1 -#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */ -#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ -#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17 -#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH -#define CONFIG_SYS_UEC1_PHY_ADDR 0 -#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII -#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 -#endif - -/* - * Environment - */ - -#ifndef CONFIG_SYS_RAMBOOT -#ifndef CONFIG_ENV_ADDR -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ - CONFIG_SYS_MONITOR_LEN) -#endif -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ -#ifndef CONFIG_ENV_OFFSET -#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN) -#endif - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -#else /* CFG_SYS_RAMBOOT */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) -#define CONFIG_ENV_SIZE 0x2000 -#endif /* CFG_SYS_RAMBOOT */ - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_NUM_I2C_BUSES 4 -#define CONFIG_SYS_I2C_MAX_HOPS 1 -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 200000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 200000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \ - {1, {I2C_NULL_HOP} } } - -#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/ - -#if defined(CONFIG_CMD_NAND) -#define CONFIG_NAND_KMETER1 -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE -#endif - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) - -/* - * Internal Definitions - */ -#define BOOTFLASH_START 0xF0000000 - -#define CONFIG_KM_CONSOLE_TTY "ttyS0" - -/* - * Environment Configuration - */ -#define CONFIG_ENV_OVERWRITE -#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ -#define CONFIG_KM_DEF_ENV "km-common=empty\0" -#endif - -#ifndef CONFIG_KM_DEF_ARCH -#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" -#endif - -#define CONFIG_EXTRA_ENV_SETTINGS \ - CONFIG_KM_DEF_ENV \ - CONFIG_KM_DEF_ARCH \ - "newenv=" \ - "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \ - "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \ - "unlock=yes\0" \ - "" - -#if defined(CONFIG_UEC_ETH) -#define CONFIG_HAS_ETH0 -#endif - -/* - * System IO Setup - */ -#define CONFIG_SYS_SICRH (SICRH_UC1EOBI | SICRH_UC2E1OBI) - -/** - * DDR RAM settings - */ -#define CONFIG_SYS_DDR_SDRAM_CFG (\ - SDRAM_CFG_SDRAM_TYPE_DDR2 | \ - SDRAM_CFG_SREN | \ - SDRAM_CFG_HSE) - -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 - /** * KMCOGE5NE has 512 MB RAM */ @@ -246,68 +44,12 @@ CSCONFIG_ROW_BIT_13 | \ CSCONFIG_COL_BIT_10)
-#define CONFIG_SYS_DDR_CLK_CNTL (\ - DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) - -#define CONFIG_SYS_DDR_INTERVAL (\ - (0x080 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ - (0x203 << SDRAM_INTERVAL_REFINT_SHIFT)) - -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f - -#define CONFIG_SYS_DDRCDR (\ - DDRCDR_EN | \ - DDRCDR_Q_DRN) -#define CONFIG_SYS_DDR_MODE 0x47860452 -#define CONFIG_SYS_DDR_MODE2 0x8080c000 - -#define CONFIG_SYS_DDR_TIMING_0 (\ - (2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ - (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ - (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ - (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ - (0 << TIMING_CFG0_WWT_SHIFT) | \ - (0 << TIMING_CFG0_RRT_SHIFT) | \ - (0 << TIMING_CFG0_WRT_SHIFT) | \ - (0 << TIMING_CFG0_RWT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_50) | \ - (2 << TIMING_CFG1_WRTORD_SHIFT) | \ - (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ - (3 << TIMING_CFG1_WRREC_SHIFT) | \ - (7 << TIMING_CFG1_REFREC_SHIFT) | \ - (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ - (8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ - (3 << TIMING_CFG1_PRETOACT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_2 (\ - (0xa << TIMING_CFG2_FOUR_ACT_SHIFT) | \ - (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ - (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ - (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ - (4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ - (5 << TIMING_CFG2_CPO_SHIFT) | \ - (0 << TIMING_CFG2_ADD_LAT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 - -/* EEprom support */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 - -/* - * PAXE on the local bus CS3 - */ -#define CONFIG_SYS_PAXE_BASE 0xA0000000 -#define CONFIG_SYS_PAXE_SIZE 256 - - /* * BFTIC3 on the local bus CS4 */ #define CONFIG_SYS_BFTIC3_BASE 0xB0000000 #define CONFIG_SYS_BFTIC3_SIZE 256
- /* enable POST tests */ #define CONFIG_POST (CONFIG_SYS_POST_MEMORY|CONFIG_SYS_POST_MEM_REGIONS) #define CONFIG_POST_EXTERNAL_WORD_FUNCS /* use own functions, not generic */ diff --git a/include/configs/kmeter1.h b/include/configs/kmeter1.h index 290108d4fc4..bfa7ca27c74 100644 --- a/include/configs/kmeter1.h +++ b/include/configs/kmeter1.h @@ -8,277 +8,23 @@ #ifndef __CONFIG_H #define __CONFIG_H
-/* KMBEC FPGA (PRIO) */ -#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000 -#define CONFIG_SYS_KMBEC_FPGA_SIZE 64 - #define CONFIG_HOSTNAME "kmeter1" #define CONFIG_KM_BOARD_NAME "kmeter1" #define CONFIG_KM_DEF_NETDEV "netdev=eth2\0"
-/* - * High Level Configuration Options - */ -#define CONFIG_QE /* Has QE */ - /* include common defines/options for all Keymile boards */ #include "km/keymile-common.h" #include "km/km-powerpc.h" - -/* - * DDR Setup - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */ -#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */ - -#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ - DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) - -#define CFG_83XX_DDR_USES_CS0 - -/* - * Manually set up DDR parameters - */ -#define CONFIG_DDR_II -#define CONFIG_SYS_DDR_SIZE 2048 /* MB */ - -/* - * The reserved memory - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#define CONFIG_SYS_FLASH_BASE 0xF0000000 - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#endif - -/* Reserve 768 kB for Mon */ -#define CONFIG_SYS_MONITOR_LEN (768 * 1024) - -/* - * Initial RAM Base Address Setup - */ -#define CONFIG_SYS_INIT_RAM_LOCK -#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) - -/* - * Init Local Bus Memory Controller: - * - * Bank Bus Machine PortSz Size Device - * ---- --- ------- ------ ----- ------ - * 0 Local GPCM 16 bit 256MB FLASH - * 1 Local GPCM 8 bit 128MB GPIO/PIGGY - * - */ -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */ - - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } - -/* - * PRIO1/PIGGY on the local bus CS1 - */ - +#include "km/km-mpc83xx.h" +#include "km/km-mpc8360.h"
/* * Serial Port */ #define CONFIG_CONS_INDEX 1 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) - -/* - * QE UEC ethernet configuration - */ -#define CONFIG_UEC_ETH -#define CONFIG_ETHPRIME "UEC0" - -#define CONFIG_UEC_ETH1 /* GETH1 */ -#define UEC_VERBOSE_DEBUG 1 - -#ifdef CONFIG_UEC_ETH1 -#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */ -#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ -#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17 -#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH -#define CONFIG_SYS_UEC1_PHY_ADDR 0 -#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII -#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 -#endif - -/* - * Environment - */ - -#ifndef CONFIG_SYS_RAMBOOT -#ifndef CONFIG_ENV_ADDR -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ - CONFIG_SYS_MONITOR_LEN) -#endif -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ -#ifndef CONFIG_ENV_OFFSET -#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN) -#endif - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -#else /* CFG_SYS_RAMBOOT */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) -#define CONFIG_ENV_SIZE 0x2000 -#endif /* CFG_SYS_RAMBOOT */ - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_NUM_I2C_BUSES 4 -#define CONFIG_SYS_I2C_MAX_HOPS 1 -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 200000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 200000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \ - {1, {I2C_NULL_HOP} } } - -#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/ - -#if defined(CONFIG_CMD_NAND) -#define CONFIG_NAND_KMETER1 -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE -#endif - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) - -/* - * Internal Definitions - */ -#define BOOTFLASH_START 0xF0000000 - -#define CONFIG_KM_CONSOLE_TTY "ttyS0" - -/* - * Environment Configuration - */ -#define CONFIG_ENV_OVERWRITE -#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ -#define CONFIG_KM_DEF_ENV "km-common=empty\0" -#endif - -#ifndef CONFIG_KM_DEF_ARCH -#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" -#endif - -#define CONFIG_EXTRA_ENV_SETTINGS \ - CONFIG_KM_DEF_ENV \ - CONFIG_KM_DEF_ARCH \ - "newenv=" \ - "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \ - "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \ - "unlock=yes\0" \ - "" - -#if defined(CONFIG_UEC_ETH) -#define CONFIG_HAS_ETH0 -#endif - -/* - * System IO Setup - */ -#define CONFIG_SYS_SICRH (SICRH_UC1EOBI | SICRH_UC2E1OBI) - -/** - * DDR RAM settings - */ -#define CONFIG_SYS_DDR_SDRAM_CFG (\ - SDRAM_CFG_SDRAM_TYPE_DDR2 | \ - SDRAM_CFG_SREN | \ - SDRAM_CFG_HSE) - -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \ CSCONFIG_ROW_BIT_13 | \ CSCONFIG_COL_BIT_10 | \ CSCONFIG_ODT_WR_ONLY_CURRENT) - -#define CONFIG_SYS_DDR_CLK_CNTL (\ - DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) - -#define CONFIG_SYS_DDR_INTERVAL (\ - (0x080 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ - (0x203 << SDRAM_INTERVAL_REFINT_SHIFT)) - -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f - -#define CONFIG_SYS_DDRCDR (\ - DDRCDR_EN | \ - DDRCDR_Q_DRN) -#define CONFIG_SYS_DDR_MODE 0x47860452 -#define CONFIG_SYS_DDR_MODE2 0x8080c000 - -#define CONFIG_SYS_DDR_TIMING_0 (\ - (2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ - (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ - (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ - (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ - (0 << TIMING_CFG0_WWT_SHIFT) | \ - (0 << TIMING_CFG0_RRT_SHIFT) | \ - (0 << TIMING_CFG0_WRT_SHIFT) | \ - (0 << TIMING_CFG0_RWT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_50) | \ - (2 << TIMING_CFG1_WRTORD_SHIFT) | \ - (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ - (3 << TIMING_CFG1_WRREC_SHIFT) | \ - (7 << TIMING_CFG1_REFREC_SHIFT) | \ - (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ - (8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ - (3 << TIMING_CFG1_PRETOACT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_2 (\ - (0xa << TIMING_CFG2_FOUR_ACT_SHIFT) | \ - (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ - (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ - (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ - (4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ - (5 << TIMING_CFG2_CPO_SHIFT) | \ - (0 << TIMING_CFG2_ADD_LAT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 - -/* EEprom support */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 - -/* - * PAXE on the local bus CS3 - */ -#define CONFIG_SYS_PAXE_BASE 0xA0000000 -#define CONFIG_SYS_PAXE_SIZE 256 - - #endif /* CONFIG */ diff --git a/include/configs/kmopti2.h b/include/configs/kmopti2.h index f1b7c2f02e3..67e864fc987 100644 --- a/include/configs/kmopti2.h +++ b/include/configs/kmopti2.h @@ -26,292 +26,10 @@ #define CONFIG_KM_BOARD_NAME "kmopti2" #define CONFIG_HOSTNAME "kmopti2"
-/* - * High Level Configuration Options - */ -#define CONFIG_QE /* Has QE */ -#define CONFIG_KM8321 /* Keymile PBEC8321 board specific */ - -#define CONFIG_KM_DEF_ARCH "arch=ppc_8xx\0" - /* include common defines/options for all Keymile boards */ #include "km/keymile-common.h" #include "km/km-powerpc.h" - -/* - * System Clock Setup - */ -#define CONFIG_83XX_CLKIN 66000000 -#define CONFIG_SYS_CLK_FREQ 66000000 -#define CONFIG_83XX_PCICLK 66000000 - -/* - * DDR Setup - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */ -#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */ - -#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ - DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) - -#define CFG_83XX_DDR_USES_CS0 - -/* - * Manually set up DDR parameters - */ -#define CONFIG_DDR_II -#define CONFIG_SYS_DDR_SIZE 2048 /* MB */ - -/* - * The reserved memory - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#define CONFIG_SYS_FLASH_BASE 0xF0000000 - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#endif - -/* Reserve 768 kB for Mon */ -#define CONFIG_SYS_MONITOR_LEN (768 * 1024) - -/* - * Initial RAM Base Address Setup - */ -#define CONFIG_SYS_INIT_RAM_LOCK -#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) - -/* - * Init Local Bus Memory Controller: - * - * Bank Bus Machine PortSz Size Device - * ---- --- ------- ------ ----- ------ - * 0 Local GPCM 16 bit 256MB FLASH - * 1 Local GPCM 8 bit 128MB GPIO/PIGGY - * - */ -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */ - - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } - -/* - * PRIO1/PIGGY on the local bus CS1 - */ - - -/* - * Serial Port - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) - -/* - * QE UEC ethernet configuration - */ -#define CONFIG_UEC_ETH -#define CONFIG_ETHPRIME "UEC0" - -#define CONFIG_UEC_ETH1 /* GETH1 */ -#define UEC_VERBOSE_DEBUG 1 - -#ifdef CONFIG_UEC_ETH1 -#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */ -#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ -#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17 -#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH -#define CONFIG_SYS_UEC1_PHY_ADDR 0 -#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII -#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 -#endif - -/* - * Environment - */ - -#ifndef CONFIG_SYS_RAMBOOT -#ifndef CONFIG_ENV_ADDR -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ - CONFIG_SYS_MONITOR_LEN) -#endif -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ -#ifndef CONFIG_ENV_OFFSET -#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN) -#endif - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -#else /* CFG_SYS_RAMBOOT */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) -#define CONFIG_ENV_SIZE 0x2000 -#endif /* CFG_SYS_RAMBOOT */ - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_NUM_I2C_BUSES 4 -#define CONFIG_SYS_I2C_MAX_HOPS 1 -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 200000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 200000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \ - {1, {I2C_NULL_HOP} } } - -#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/ - -#if defined(CONFIG_CMD_NAND) -#define CONFIG_NAND_KMETER1 -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE -#endif - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) - -/* - * Internal Definitions - */ -#define BOOTFLASH_START 0xF0000000 - -#define CONFIG_KM_CONSOLE_TTY "ttyS0" - -/* - * Environment Configuration - */ -#define CONFIG_ENV_OVERWRITE -#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ -#define CONFIG_KM_DEF_ENV "km-common=empty\0" -#endif - -#ifndef CONFIG_KM_DEF_ARCH -#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" -#endif - -#define CONFIG_EXTRA_ENV_SETTINGS \ - CONFIG_KM_DEF_ENV \ - CONFIG_KM_DEF_ARCH \ - "newenv=" \ - "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \ - "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \ - "unlock=yes\0" \ - "" - -#if defined(CONFIG_UEC_ETH) -#define CONFIG_HAS_ETH0 -#endif - -/* - * System IO Config - */ -#define CONFIG_SYS_SICRL SICRL_IRQ_CKS - -#define CONFIG_SYS_DDRCDR (\ - DDRCDR_EN | \ - DDRCDR_PZ_MAXZ | \ - DDRCDR_NZ_MAXZ | \ - DDRCDR_M_ODR) - -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f -#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \ - SDRAM_CFG_32_BE | \ - SDRAM_CFG_SREN | \ - SDRAM_CFG_HSE) - -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 -#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) -#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ - (0x200 << SDRAM_INTERVAL_REFINT_SHIFT)) - -#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \ - CSCONFIG_ODT_WR_CFG | \ - CSCONFIG_ROW_BIT_13 | \ - CSCONFIG_COL_BIT_10) - -#define CONFIG_SYS_DDR_MODE 0x47860242 -#define CONFIG_SYS_DDR_MODE2 0x8080c000 - -#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ - (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ - (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ - (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ - (0 << TIMING_CFG0_WWT_SHIFT) | \ - (0 << TIMING_CFG0_RRT_SHIFT) | \ - (0 << TIMING_CFG0_WRT_SHIFT) | \ - (0 << TIMING_CFG0_RWT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \ - (2 << TIMING_CFG1_WRTORD_SHIFT) | \ - (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ - (3 << TIMING_CFG1_WRREC_SHIFT) | \ - (7 << TIMING_CFG1_REFREC_SHIFT) | \ - (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ - (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ - (3 << TIMING_CFG1_PRETOACT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ - (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ - (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ - (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ - (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ - (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ - (5 << TIMING_CFG2_CPO_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 - -#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000 -#define CONFIG_SYS_KMBEC_FPGA_SIZE 128 - -/* EEprom support */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - -/* - * Init Local Bus Memory Controller: - * Device on board - * Bank Bus Machine PortSz Size TUDA1 TUXA1 TUGE1 KMSUPX4 KMOPTI2 - * ----------------------------------------------------------------------------- - * 2 Local GPCM 8 bit 256MB PAXG LPXF PAXI LPXF PAXE - * 3 Local GPCM 8 bit 256MB PINC3 PINC2 unused unused OPI2(16 bit) - * - * Device on board (continued) - * Bank Bus Machine PortSz Size KMTEPR2 - * ----------------------------------------------------------------------------- - * 2 Local GPCM 8 bit 256MB NVRAM - * 3 Local GPCM 8 bit 256MB TEP2 (16 bit) - */ - -/* - * Configuration for C2 on the local bus - */ - - -/* - * Configuration for C3 on the local bus - */ - +#include "km/km-mpc83xx.h" +#include "km/km-mpc832x.h"
#endif /* __CONFIG_H */ diff --git a/include/configs/kmsupx5.h b/include/configs/kmsupx5.h index 0dd7420e8c9..ba33e6074bf 100644 --- a/include/configs/kmsupx5.h +++ b/include/configs/kmsupx5.h @@ -26,283 +26,10 @@ #define CONFIG_KM_BOARD_NAME "kmsupx5" #define CONFIG_HOSTNAME "kmsupx5"
-/* - * High Level Configuration Options - */ -#define CONFIG_QE /* Has QE */ -#define CONFIG_KM8321 /* Keymile PBEC8321 board specific */ - -#define CONFIG_KM_DEF_ARCH "arch=ppc_8xx\0" - /* include common defines/options for all Keymile boards */ #include "km/keymile-common.h" #include "km/km-powerpc.h" - -/* - * System Clock Setup - */ -#define CONFIG_83XX_CLKIN 66000000 -#define CONFIG_SYS_CLK_FREQ 66000000 -#define CONFIG_83XX_PCICLK 66000000 - -/* - * DDR Setup - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */ -#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */ - -#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ - DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) - -#define CFG_83XX_DDR_USES_CS0 - -/* - * Manually set up DDR parameters - */ -#define CONFIG_DDR_II -#define CONFIG_SYS_DDR_SIZE 2048 /* MB */ - -/* - * The reserved memory - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#define CONFIG_SYS_FLASH_BASE 0xF0000000 - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#endif - -/* Reserve 768 kB for Mon */ -#define CONFIG_SYS_MONITOR_LEN (768 * 1024) - -/* - * Initial RAM Base Address Setup - */ -#define CONFIG_SYS_INIT_RAM_LOCK -#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) - -/* - * Init Local Bus Memory Controller: - * - * Bank Bus Machine PortSz Size Device - * ---- --- ------- ------ ----- ------ - * 0 Local GPCM 16 bit 256MB FLASH - * 1 Local GPCM 8 bit 128MB GPIO/PIGGY - * - */ -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */ - - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } - -/* - * PRIO1/PIGGY on the local bus CS1 - */ - - -/* - * Serial Port - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) - -/* - * QE UEC ethernet configuration - */ -#define CONFIG_UEC_ETH -#define CONFIG_ETHPRIME "UEC0" - -#define CONFIG_UEC_ETH1 /* GETH1 */ -#define UEC_VERBOSE_DEBUG 1 - -#ifdef CONFIG_UEC_ETH1 -#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */ -#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ -#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17 -#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH -#define CONFIG_SYS_UEC1_PHY_ADDR 0 -#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII -#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 -#endif - -/* - * Environment - */ - -#ifndef CONFIG_SYS_RAMBOOT -#ifndef CONFIG_ENV_ADDR -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ - CONFIG_SYS_MONITOR_LEN) -#endif -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ -#ifndef CONFIG_ENV_OFFSET -#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN) -#endif - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -#else /* CFG_SYS_RAMBOOT */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) -#define CONFIG_ENV_SIZE 0x2000 -#endif /* CFG_SYS_RAMBOOT */ - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_NUM_I2C_BUSES 4 -#define CONFIG_SYS_I2C_MAX_HOPS 1 -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 200000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 200000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \ - {1, {I2C_NULL_HOP} } } - -#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/ - -#if defined(CONFIG_CMD_NAND) -#define CONFIG_NAND_KMETER1 -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE -#endif - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) - -/* - * Internal Definitions - */ -#define BOOTFLASH_START 0xF0000000 - -#define CONFIG_KM_CONSOLE_TTY "ttyS0" - -/* - * Environment Configuration - */ -#define CONFIG_ENV_OVERWRITE -#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ -#define CONFIG_KM_DEF_ENV "km-common=empty\0" -#endif - -#ifndef CONFIG_KM_DEF_ARCH -#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" -#endif - -#define CONFIG_EXTRA_ENV_SETTINGS \ - CONFIG_KM_DEF_ENV \ - CONFIG_KM_DEF_ARCH \ - "newenv=" \ - "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \ - "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \ - "unlock=yes\0" \ - "" - -#if defined(CONFIG_UEC_ETH) -#define CONFIG_HAS_ETH0 -#endif - -/* - * System IO Config - */ -#define CONFIG_SYS_SICRL SICRL_IRQ_CKS - -#define CONFIG_SYS_DDRCDR (\ - DDRCDR_EN | \ - DDRCDR_PZ_MAXZ | \ - DDRCDR_NZ_MAXZ | \ - DDRCDR_M_ODR) - -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f -#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \ - SDRAM_CFG_32_BE | \ - SDRAM_CFG_SREN | \ - SDRAM_CFG_HSE) - -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 -#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) -#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ - (0x200 << SDRAM_INTERVAL_REFINT_SHIFT)) - -#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \ - CSCONFIG_ODT_WR_CFG | \ - CSCONFIG_ROW_BIT_13 | \ - CSCONFIG_COL_BIT_10) - -#define CONFIG_SYS_DDR_MODE 0x47860242 -#define CONFIG_SYS_DDR_MODE2 0x8080c000 - -#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ - (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ - (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ - (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ - (0 << TIMING_CFG0_WWT_SHIFT) | \ - (0 << TIMING_CFG0_RRT_SHIFT) | \ - (0 << TIMING_CFG0_WRT_SHIFT) | \ - (0 << TIMING_CFG0_RWT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \ - (2 << TIMING_CFG1_WRTORD_SHIFT) | \ - (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ - (3 << TIMING_CFG1_WRREC_SHIFT) | \ - (7 << TIMING_CFG1_REFREC_SHIFT) | \ - (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ - (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ - (3 << TIMING_CFG1_PRETOACT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ - (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ - (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ - (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ - (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ - (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ - (5 << TIMING_CFG2_CPO_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 - -#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000 -#define CONFIG_SYS_KMBEC_FPGA_SIZE 128 - -/* EEprom support */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - -/* - * Init Local Bus Memory Controller: - * Device on board - * Bank Bus Machine PortSz Size TUDA1 TUXA1 TUGE1 KMSUPX4 KMOPTI2 - * ----------------------------------------------------------------------------- - * 2 Local GPCM 8 bit 256MB PAXG LPXF PAXI LPXF PAXE - * 3 Local GPCM 8 bit 256MB PINC3 PINC2 unused unused OPI2(16 bit) - * - * Device on board (continued) - * Bank Bus Machine PortSz Size KMTEPR2 - * ----------------------------------------------------------------------------- - * 2 Local GPCM 8 bit 256MB NVRAM - * 3 Local GPCM 8 bit 256MB TEP2 (16 bit) - */ - +#include "km/km-mpc83xx.h" +#include "km/km-mpc832x.h"
#endif /* __CONFIG_H */ diff --git a/include/configs/kmtegr1.h b/include/configs/kmtegr1.h index 8f9bbefa7fa..701eb53f631 100644 --- a/include/configs/kmtegr1.h +++ b/include/configs/kmtegr1.h @@ -33,340 +33,13 @@ #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define NAND_MAX_CHIPS 1
-/* - * High Level Configuration Options - */ -#define CONFIG_E300 1 /* E300 family */ -#define CONFIG_QE 1 /* Has QE */ - -#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" - /* include common defines/options for all Keymile boards */ #include "km/keymile-common.h" #include "km/km-powerpc.h" - -/* - * System Clock Setup - */ -#define CONFIG_83XX_CLKIN 66000000 -#define CONFIG_SYS_CLK_FREQ 66000000 -#define CONFIG_83XX_PCICLK 66000000 - -/* - * DDR Setup - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */ -#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */ - -#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ - DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) - -#define CFG_83XX_DDR_USES_CS0 - -/* - * Manually set up DDR parameters - */ -#define CONFIG_DDR_II -#define CONFIG_SYS_DDR_SIZE 2048 /* MB */ - -/* - * The reserved memory - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#define CONFIG_SYS_FLASH_BASE 0xF0000000 - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#endif - -/* Reserve 768 kB for Mon */ -#define CONFIG_SYS_MONITOR_LEN (768 * 1024) - -/* - * Initial RAM Base Address Setup - */ -#define CONFIG_SYS_INIT_RAM_LOCK -#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) - -/* - * Init Local Bus Memory Controller: - * - * Bank Bus Machine PortSz Size Device - * ---- --- ------- ------ ----- ------ - * 0 Local GPCM 16 bit 256MB FLASH - * 1 Local GPCM 8 bit 128MB GPIO/PIGGY - * - */ -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */ - - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } - -/* - * PRIO1/PIGGY on the local bus CS1 - */ - - -/* - * Serial Port - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) - -/* - * QE UEC ethernet configuration - */ -#define CONFIG_UEC_ETH -#define CONFIG_ETHPRIME "UEC0" - -#ifdef CONFIG_UEC_ETH1 -#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */ -#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ -#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17 -#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH -#define CONFIG_SYS_UEC1_PHY_ADDR 0 -#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII -#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 -#endif - -/* - * Environment - */ - -#ifndef CONFIG_SYS_RAMBOOT -#ifndef CONFIG_ENV_ADDR -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ - CONFIG_SYS_MONITOR_LEN) -#endif -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ -#ifndef CONFIG_ENV_OFFSET -#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN) -#endif - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -#else /* CFG_SYS_RAMBOOT */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) -#define CONFIG_ENV_SIZE 0x2000 -#endif /* CFG_SYS_RAMBOOT */ - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_NUM_I2C_BUSES 4 -#define CONFIG_SYS_I2C_MAX_HOPS 1 -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 200000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 200000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \ - {1, {I2C_NULL_HOP} } } - -#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/ - -#if defined(CONFIG_CMD_NAND) -#define CONFIG_NAND_KMETER1 -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE -#endif - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) - -/* - * Internal Definitions - */ -#define BOOTFLASH_START 0xF0000000 - -#define CONFIG_KM_CONSOLE_TTY "ttyS0" - -/* - * Environment Configuration - */ -#define CONFIG_ENV_OVERWRITE -#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ -#define CONFIG_KM_DEF_ENV "km-common=empty\0" -#endif - -#ifndef CONFIG_KM_DEF_ARCH -#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" -#endif - -#define CONFIG_EXTRA_ENV_SETTINGS \ - CONFIG_KM_DEF_ENV \ - CONFIG_KM_DEF_ARCH \ - "newenv=" \ - "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \ - "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \ - "unlock=yes\0" \ - "" - -#if defined(CONFIG_UEC_ETH) -#define CONFIG_HAS_ETH0 -#endif - -/* QE microcode/firmware address */ -#define CONFIG_SYS_QE_FMAN_FW_IN_NOR -/* between the u-boot partition and env */ -#ifndef CONFIG_SYS_QE_FW_ADDR -#define CONFIG_SYS_QE_FW_ADDR 0xF00C0000 -#endif - -/* - * System IO Config - */ -/* 0x14000180 SICR_1 */ -#define CONFIG_SYS_SICRL (0 \ - | SICR_1_UART1_UART1RTS \ - | SICR_1_I2C_CKSTOP \ - | SICR_1_IRQ_A_IRQ \ - | SICR_1_IRQ_B_IRQ \ - | SICR_1_GPIO_A_GPIO \ - | SICR_1_GPIO_B_GPIO \ - | SICR_1_GPIO_C_GPIO \ - | SICR_1_GPIO_D_GPIO \ - | SICR_1_GPIO_E_GPIO \ - | SICR_1_GPIO_F_GPIO \ - | SICR_1_USB_A_UART2S \ - | SICR_1_USB_B_UART2RTS \ - | SICR_1_FEC1_FEC1 \ - | SICR_1_FEC2_FEC2 \ - ) - -/* 0x00080400 SICR_2 */ -#define CONFIG_SYS_SICRH (0 \ - | SICR_2_FEC3_FEC3 \ - | SICR_2_HDLC1_A_HDLC1 \ - | SICR_2_ELBC_A_LA \ - | SICR_2_ELBC_B_LCLK \ - | SICR_2_HDLC2_A_HDLC2 \ - | SICR_2_USB_D_GPIO \ - | SICR_2_PCI_PCI \ - | SICR_2_HDLC1_B_HDLC1 \ - | SICR_2_HDLC1_C_HDLC1 \ - | SICR_2_HDLC2_B_GPIO \ - | SICR_2_HDLC2_C_HDLC2 \ - | SICR_2_QUIESCE_B \ - ) - -/* GPR_1 */ -#define CONFIG_SYS_GPR1 0x50008060 - -#define CONFIG_SYS_GP1DIR 0x00000000 -#define CONFIG_SYS_GP1ODR 0x00000000 -#define CONFIG_SYS_GP2DIR 0xFF000000 -#define CONFIG_SYS_GP2ODR 0x00000000 - -#define CONFIG_SYS_DDRCDR (\ - DDRCDR_EN | \ - DDRCDR_PZ_MAXZ | \ - DDRCDR_NZ_MAXZ | \ - DDRCDR_M_ODR) - -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f -#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \ - SDRAM_CFG_32_BE | \ - SDRAM_CFG_SREN | \ - SDRAM_CFG_HSE) - -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 -#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) -#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ - (0x200 << SDRAM_INTERVAL_REFINT_SHIFT)) - -#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \ - CSCONFIG_ODT_RD_NEVER | \ - CSCONFIG_ODT_WR_ONLY_CURRENT | \ - CSCONFIG_ROW_BIT_13 | \ - CSCONFIG_COL_BIT_10) - -#define CONFIG_SYS_DDR_MODE 0x47860242 -#define CONFIG_SYS_DDR_MODE2 0x8080c000 - -#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ - (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ - (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ - (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ - (0 << TIMING_CFG0_WWT_SHIFT) | \ - (0 << TIMING_CFG0_RRT_SHIFT) | \ - (0 << TIMING_CFG0_WRT_SHIFT) | \ - (0 << TIMING_CFG0_RWT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \ - (2 << TIMING_CFG1_WRTORD_SHIFT) | \ - (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ - (3 << TIMING_CFG1_WRREC_SHIFT) | \ - (7 << TIMING_CFG1_REFREC_SHIFT) | \ - (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ - (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ - (3 << TIMING_CFG1_PRETOACT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ - (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ - (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ - (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ - (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ - (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ - (5 << TIMING_CFG2_CPO_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 - -#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000 -#define CONFIG_SYS_KMBEC_FPGA_SIZE 128 - -/* EEprom support */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#include "km/km-mpc83xx.h" +#include "km/km-mpc8309.h"
/* must be after the include because KMBEC_FPGA is otherwise undefined */ #define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE /* PRIO_BASE_ADDRESS */
-/* EEprom support */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - -/* - * Init Local Bus Memory Controller: - * - * Bank Bus Machine PortSz Size Device - * ---- --- ------- ------ ----- ------ - * 2 Local UPMA 16 bit 256MB APP1 - * 3 Local GPCM 16 bit 256MB APP2 - * - */ - - -/* ethernet port connected to piggy (UEC2) */ -#define CONFIG_HAS_ETH1 -#define CONFIG_UEC_ETH2 -#define CONFIG_SYS_UEC2_UCC_NUM 2 /* UCC3 */ -#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ -#define CONFIG_SYS_UEC2_TX_CLK QE_CLK12 -#define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH -#define CONFIG_SYS_UEC2_PHY_ADDR 0 -#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII -#define CONFIG_SYS_UEC2_INTERFACE_SPEED 100 - #endif /* __CONFIG_H */ diff --git a/include/configs/kmtepr2.h b/include/configs/kmtepr2.h index b77219f72cb..e0c907d11a4 100644 --- a/include/configs/kmtepr2.h +++ b/include/configs/kmtepr2.h @@ -26,284 +26,10 @@ #define CONFIG_KM_BOARD_NAME "kmtepr2" #define CONFIG_HOSTNAME "kmtepr2"
-/* - * High Level Configuration Options - */ -#define CONFIG_QE /* Has QE */ -#define CONFIG_KM8321 /* Keymile PBEC8321 board specific */ - -#define CONFIG_KM_DEF_ARCH "arch=ppc_8xx\0" - /* include common defines/options for all Keymile boards */ #include "km/keymile-common.h" #include "km/km-powerpc.h" - -/* - * System Clock Setup - */ -#define CONFIG_83XX_CLKIN 66000000 -#define CONFIG_SYS_CLK_FREQ 66000000 -#define CONFIG_83XX_PCICLK 66000000 - -/* - * DDR Setup - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */ -#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */ - -#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ - DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) - -#define CFG_83XX_DDR_USES_CS0 - -/* - * Manually set up DDR parameters - */ -#define CONFIG_DDR_II -#define CONFIG_SYS_DDR_SIZE 2048 /* MB */ - -/* - * The reserved memory - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#define CONFIG_SYS_FLASH_BASE 0xF0000000 - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#endif - -/* Reserve 768 kB for Mon */ -#define CONFIG_SYS_MONITOR_LEN (768 * 1024) - -/* - * Initial RAM Base Address Setup - */ -#define CONFIG_SYS_INIT_RAM_LOCK -#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) - -/* - * Init Local Bus Memory Controller: - * - * Bank Bus Machine PortSz Size Device - * ---- --- ------- ------ ----- ------ - * 0 Local GPCM 16 bit 256MB FLASH - * 1 Local GPCM 8 bit 128MB GPIO/PIGGY - * - */ -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */ - - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } - -/* - * PRIO1/PIGGY on the local bus CS1 - */ - - -/* - * Serial Port - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) - -/* - * QE UEC ethernet configuration - */ -#define CONFIG_UEC_ETH -#define CONFIG_ETHPRIME "UEC0" - -#define CONFIG_UEC_ETH1 /* GETH1 */ -#define UEC_VERBOSE_DEBUG 1 - -#ifdef CONFIG_UEC_ETH1 -#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */ -#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ -#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17 -#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH -#define CONFIG_SYS_UEC1_PHY_ADDR 0 -#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII -#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 -#endif - -/* - * Environment - */ - -#ifndef CONFIG_SYS_RAMBOOT -#ifndef CONFIG_ENV_ADDR -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ - CONFIG_SYS_MONITOR_LEN) -#endif -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ -#ifndef CONFIG_ENV_OFFSET -#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN) -#endif - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -#else /* CFG_SYS_RAMBOOT */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) -#define CONFIG_ENV_SIZE 0x2000 -#endif /* CFG_SYS_RAMBOOT */ - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_NUM_I2C_BUSES 4 -#define CONFIG_SYS_I2C_MAX_HOPS 1 -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 200000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 200000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \ - {1, {I2C_NULL_HOP} } } - -#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/ - -#if defined(CONFIG_CMD_NAND) -#define CONFIG_NAND_KMETER1 -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE -#endif - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) - -/* - * Internal Definitions - */ -#define BOOTFLASH_START 0xF0000000 - -#define CONFIG_KM_CONSOLE_TTY "ttyS0" - -/* - * Environment Configuration - */ -#define CONFIG_ENV_OVERWRITE -#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ -#define CONFIG_KM_DEF_ENV "km-common=empty\0" -#endif - -#ifndef CONFIG_KM_DEF_ARCH -#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" -#endif - -#define CONFIG_EXTRA_ENV_SETTINGS \ - CONFIG_KM_DEF_ENV \ - CONFIG_KM_DEF_ARCH \ - "newenv=" \ - "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \ - "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \ - "unlock=yes\0" \ - "" - -#if defined(CONFIG_UEC_ETH) -#define CONFIG_HAS_ETH0 -#endif - -/* - * System IO Config - */ -#define CONFIG_SYS_SICRL SICRL_IRQ_CKS - -#define CONFIG_SYS_DDRCDR (\ - DDRCDR_EN | \ - DDRCDR_PZ_MAXZ | \ - DDRCDR_NZ_MAXZ | \ - DDRCDR_M_ODR) - -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f -#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \ - SDRAM_CFG_32_BE | \ - SDRAM_CFG_SREN | \ - SDRAM_CFG_HSE) - -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 -#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) -#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ - (0x200 << SDRAM_INTERVAL_REFINT_SHIFT)) - -#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \ - CSCONFIG_ODT_WR_CFG | \ - CSCONFIG_ROW_BIT_13 | \ - CSCONFIG_COL_BIT_10) - -#define CONFIG_SYS_DDR_MODE 0x47860242 -#define CONFIG_SYS_DDR_MODE2 0x8080c000 - -#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ - (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ - (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ - (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ - (0 << TIMING_CFG0_WWT_SHIFT) | \ - (0 << TIMING_CFG0_RRT_SHIFT) | \ - (0 << TIMING_CFG0_WRT_SHIFT) | \ - (0 << TIMING_CFG0_RWT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \ - (2 << TIMING_CFG1_WRTORD_SHIFT) | \ - (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ - (3 << TIMING_CFG1_WRREC_SHIFT) | \ - (7 << TIMING_CFG1_REFREC_SHIFT) | \ - (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ - (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ - (3 << TIMING_CFG1_PRETOACT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ - (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ - (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ - (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ - (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ - (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ - (5 << TIMING_CFG2_CPO_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 - -#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000 -#define CONFIG_SYS_KMBEC_FPGA_SIZE 128 - -/* EEprom support */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - -/* - * Init Local Bus Memory Controller: - * Device on board - * Bank Bus Machine PortSz Size TUDA1 TUXA1 TUGE1 KMSUPX4 KMOPTI2 - * ----------------------------------------------------------------------------- - * 2 Local GPCM 8 bit 256MB PAXG LPXF PAXI LPXF PAXE - * 3 Local GPCM 8 bit 256MB PINC3 PINC2 unused unused OPI2(16 bit) - * - * Device on board (continued) - * Bank Bus Machine PortSz Size KMTEPR2 - * ----------------------------------------------------------------------------- - * 2 Local GPCM 8 bit 256MB NVRAM - * 3 Local GPCM 8 bit 256MB TEP2 (16 bit) - */ - - +#include "km/km-mpc83xx.h" +#include "km/km-mpc832x.h"
#endif /* __CONFIG_H */ diff --git a/include/configs/kmvect1.h b/include/configs/kmvect1.h index 785475ef458..6e5d50700c0 100644 --- a/include/configs/kmvect1.h +++ b/include/configs/kmvect1.h @@ -25,328 +25,11 @@ /* at end of uboot partition, before env */ #define CONFIG_SYS_QE_FW_ADDR 0xF00B0000
-/* - * High Level Configuration Options - */ -#define CONFIG_E300 1 /* E300 family */ -#define CONFIG_QE 1 /* Has QE */ - -#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" - /* include common defines/options for all Keymile boards */ #include "km/keymile-common.h" #include "km/km-powerpc.h" - -/* - * System Clock Setup - */ -#define CONFIG_83XX_CLKIN 66000000 -#define CONFIG_SYS_CLK_FREQ 66000000 -#define CONFIG_83XX_PCICLK 66000000 - -/* - * DDR Setup - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */ -#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */ - -#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ - DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) - -#define CFG_83XX_DDR_USES_CS0 - -/* - * Manually set up DDR parameters - */ -#define CONFIG_DDR_II -#define CONFIG_SYS_DDR_SIZE 2048 /* MB */ - -/* - * The reserved memory - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#define CONFIG_SYS_FLASH_BASE 0xF0000000 - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#endif - -/* Reserve 768 kB for Mon */ -#define CONFIG_SYS_MONITOR_LEN (768 * 1024) - -/* - * Initial RAM Base Address Setup - */ -#define CONFIG_SYS_INIT_RAM_LOCK -#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) - -/* - * Init Local Bus Memory Controller: - * - * Bank Bus Machine PortSz Size Device - * ---- --- ------- ------ ----- ------ - * 0 Local GPCM 16 bit 256MB FLASH - * 1 Local GPCM 8 bit 128MB GPIO/PIGGY - * - */ -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */ - - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } - -/* - * PRIO1/PIGGY on the local bus CS1 - */ - - -/* - * Serial Port - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) - -/* - * QE UEC ethernet configuration - */ -#define CONFIG_UEC_ETH -#define CONFIG_ETHPRIME "UEC0" - -#ifdef CONFIG_UEC_ETH1 -#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */ -#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ -#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17 -#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH -#define CONFIG_SYS_UEC1_PHY_ADDR 0 -#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII -#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 -#endif - -/* - * Environment - */ - -#ifndef CONFIG_SYS_RAMBOOT -#ifndef CONFIG_ENV_ADDR -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ - CONFIG_SYS_MONITOR_LEN) -#endif -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ -#ifndef CONFIG_ENV_OFFSET -#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN) -#endif - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -#else /* CFG_SYS_RAMBOOT */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) -#define CONFIG_ENV_SIZE 0x2000 -#endif /* CFG_SYS_RAMBOOT */ - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_NUM_I2C_BUSES 4 -#define CONFIG_SYS_I2C_MAX_HOPS 1 -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 200000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 200000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \ - {1, {I2C_NULL_HOP} } } - -#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/ - -#if defined(CONFIG_CMD_NAND) -#define CONFIG_NAND_KMETER1 -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE -#endif - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) - -/* - * Internal Definitions - */ -#define BOOTFLASH_START 0xF0000000 - -#define CONFIG_KM_CONSOLE_TTY "ttyS0" - -/* - * Environment Configuration - */ -#define CONFIG_ENV_OVERWRITE -#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ -#define CONFIG_KM_DEF_ENV "km-common=empty\0" -#endif - -#ifndef CONFIG_KM_DEF_ARCH -#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" -#endif - -#define CONFIG_EXTRA_ENV_SETTINGS \ - CONFIG_KM_DEF_ENV \ - CONFIG_KM_DEF_ARCH \ - "newenv=" \ - "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \ - "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \ - "unlock=yes\0" \ - "" - -#if defined(CONFIG_UEC_ETH) -#define CONFIG_HAS_ETH0 -#endif - -/* QE microcode/firmware address */ -#define CONFIG_SYS_QE_FMAN_FW_IN_NOR -/* between the u-boot partition and env */ -#ifndef CONFIG_SYS_QE_FW_ADDR -#define CONFIG_SYS_QE_FW_ADDR 0xF00C0000 -#endif - -/* - * System IO Config - */ -/* 0x14000180 SICR_1 */ -#define CONFIG_SYS_SICRL (0 \ - | SICR_1_UART1_UART1RTS \ - | SICR_1_I2C_CKSTOP \ - | SICR_1_IRQ_A_IRQ \ - | SICR_1_IRQ_B_IRQ \ - | SICR_1_GPIO_A_GPIO \ - | SICR_1_GPIO_B_GPIO \ - | SICR_1_GPIO_C_GPIO \ - | SICR_1_GPIO_D_GPIO \ - | SICR_1_GPIO_E_GPIO \ - | SICR_1_GPIO_F_GPIO \ - | SICR_1_USB_A_UART2S \ - | SICR_1_USB_B_UART2RTS \ - | SICR_1_FEC1_FEC1 \ - | SICR_1_FEC2_FEC2 \ - ) - -/* 0x00080400 SICR_2 */ -#define CONFIG_SYS_SICRH (0 \ - | SICR_2_FEC3_FEC3 \ - | SICR_2_HDLC1_A_HDLC1 \ - | SICR_2_ELBC_A_LA \ - | SICR_2_ELBC_B_LCLK \ - | SICR_2_HDLC2_A_HDLC2 \ - | SICR_2_USB_D_GPIO \ - | SICR_2_PCI_PCI \ - | SICR_2_HDLC1_B_HDLC1 \ - | SICR_2_HDLC1_C_HDLC1 \ - | SICR_2_HDLC2_B_GPIO \ - | SICR_2_HDLC2_C_HDLC2 \ - | SICR_2_QUIESCE_B \ - ) - -/* GPR_1 */ -#define CONFIG_SYS_GPR1 0x50008060 - -#define CONFIG_SYS_GP1DIR 0x00000000 -#define CONFIG_SYS_GP1ODR 0x00000000 -#define CONFIG_SYS_GP2DIR 0xFF000000 -#define CONFIG_SYS_GP2ODR 0x00000000 - -#define CONFIG_SYS_DDRCDR (\ - DDRCDR_EN | \ - DDRCDR_PZ_MAXZ | \ - DDRCDR_NZ_MAXZ | \ - DDRCDR_M_ODR) - -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f -#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \ - SDRAM_CFG_32_BE | \ - SDRAM_CFG_SREN | \ - SDRAM_CFG_HSE) - -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 -#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) -#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ - (0x200 << SDRAM_INTERVAL_REFINT_SHIFT)) - -#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \ - CSCONFIG_ODT_RD_NEVER | \ - CSCONFIG_ODT_WR_ONLY_CURRENT | \ - CSCONFIG_ROW_BIT_13 | \ - CSCONFIG_COL_BIT_10) - -#define CONFIG_SYS_DDR_MODE 0x47860242 -#define CONFIG_SYS_DDR_MODE2 0x8080c000 - -#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ - (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ - (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ - (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ - (0 << TIMING_CFG0_WWT_SHIFT) | \ - (0 << TIMING_CFG0_RRT_SHIFT) | \ - (0 << TIMING_CFG0_WRT_SHIFT) | \ - (0 << TIMING_CFG0_RWT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \ - (2 << TIMING_CFG1_WRTORD_SHIFT) | \ - (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ - (3 << TIMING_CFG1_WRREC_SHIFT) | \ - (7 << TIMING_CFG1_REFREC_SHIFT) | \ - (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ - (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ - (3 << TIMING_CFG1_PRETOACT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ - (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ - (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ - (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ - (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ - (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ - (5 << TIMING_CFG2_CPO_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 - -#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000 -#define CONFIG_SYS_KMBEC_FPGA_SIZE 128 - -/* EEprom support */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - -/* EEprom support */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - -/* - * Init Local Bus Memory Controller: - * - * Bank Bus Machine PortSz Size Device - * ---- --- ------- ------ ----- ------ - * 2 Local UPMA 16 bit 256MB APP1 - * 3 Local GPCM 16 bit 256MB APP2 - * - */ - - +#include "km/km-mpc83xx.h" +#include "km/km-mpc8309.h"
#define CONFIG_SYS_MAMR (MxMR_GPL_x4DIS | \ 0x0000c000 | \ @@ -375,15 +58,4 @@ #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII #define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
-/* ethernet port connected to piggy (UEC2) */ -#define CONFIG_HAS_ETH1 -#define CONFIG_UEC_ETH2 -#define CONFIG_SYS_UEC2_UCC_NUM 2 /* UCC3 */ -#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ -#define CONFIG_SYS_UEC2_TX_CLK QE_CLK12 -#define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH -#define CONFIG_SYS_UEC2_PHY_ADDR 0 -#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII -#define CONFIG_SYS_UEC2_INTERFACE_SPEED 100 - #endif /* __CONFIG_H */ diff --git a/include/configs/suvd3.h b/include/configs/suvd3.h index 456cd9dd707..1705f9cafba 100644 --- a/include/configs/suvd3.h +++ b/include/configs/suvd3.h @@ -21,285 +21,13 @@ */
#define CONFIG_HOSTNAME "suvd3" -#define CONFIG_KM_BOARD_NAME "suvd3" - -/* - * High Level Configuration Options - */ -#define CONFIG_QE /* Has QE */ -#define CONFIG_KM8321 /* Keymile PBEC8321 board specific */ - -#define CONFIG_KM_DEF_ARCH "arch=ppc_8xx\0" +#define CONFIG_KM_BOARD_NAME "suvd3"
/* include common defines/options for all Keymile boards */ #include "km/keymile-common.h" #include "km/km-powerpc.h" - -/* - * System Clock Setup - */ -#define CONFIG_83XX_CLKIN 66000000 -#define CONFIG_SYS_CLK_FREQ 66000000 -#define CONFIG_83XX_PCICLK 66000000 - -/* - * DDR Setup - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */ -#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */ - -#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ - DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) - -#define CFG_83XX_DDR_USES_CS0 - -/* - * Manually set up DDR parameters - */ -#define CONFIG_DDR_II -#define CONFIG_SYS_DDR_SIZE 2048 /* MB */ - -/* - * The reserved memory - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#define CONFIG_SYS_FLASH_BASE 0xF0000000 - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#endif - -/* Reserve 768 kB for Mon */ -#define CONFIG_SYS_MONITOR_LEN (768 * 1024) - -/* - * Initial RAM Base Address Setup - */ -#define CONFIG_SYS_INIT_RAM_LOCK -#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) - -/* - * Init Local Bus Memory Controller: - * - * Bank Bus Machine PortSz Size Device - * ---- --- ------- ------ ----- ------ - * 0 Local GPCM 16 bit 256MB FLASH - * 1 Local GPCM 8 bit 128MB GPIO/PIGGY - * - */ -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */ - - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } - -/* - * PRIO1/PIGGY on the local bus CS1 - */ - - -/* - * Serial Port - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) - -/* - * QE UEC ethernet configuration - */ -#define CONFIG_UEC_ETH -#define CONFIG_ETHPRIME "UEC0" - -#define CONFIG_UEC_ETH1 /* GETH1 */ -#define UEC_VERBOSE_DEBUG 1 - -#ifdef CONFIG_UEC_ETH1 -#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */ -#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ -#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17 -#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH -#define CONFIG_SYS_UEC1_PHY_ADDR 0 -#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII -#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 -#endif - -/* - * Environment - */ - -#ifndef CONFIG_SYS_RAMBOOT -#ifndef CONFIG_ENV_ADDR -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ - CONFIG_SYS_MONITOR_LEN) -#endif -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ -#ifndef CONFIG_ENV_OFFSET -#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN) -#endif - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -#else /* CFG_SYS_RAMBOOT */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) -#define CONFIG_ENV_SIZE 0x2000 -#endif /* CFG_SYS_RAMBOOT */ - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_NUM_I2C_BUSES 4 -#define CONFIG_SYS_I2C_MAX_HOPS 1 -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 200000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 200000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \ - {1, {I2C_NULL_HOP} } } - -#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/ - -#if defined(CONFIG_CMD_NAND) -#define CONFIG_NAND_KMETER1 -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE -#endif - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) - -/* - * Internal Definitions - */ -#define BOOTFLASH_START 0xF0000000 - -#define CONFIG_KM_CONSOLE_TTY "ttyS0" - -/* - * Environment Configuration - */ -#define CONFIG_ENV_OVERWRITE -#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ -#define CONFIG_KM_DEF_ENV "km-common=empty\0" -#endif - -#ifndef CONFIG_KM_DEF_ARCH -#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" -#endif - -#define CONFIG_EXTRA_ENV_SETTINGS \ - CONFIG_KM_DEF_ENV \ - CONFIG_KM_DEF_ARCH \ - "newenv=" \ - "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \ - "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \ - "unlock=yes\0" \ - "" - -#if defined(CONFIG_UEC_ETH) -#define CONFIG_HAS_ETH0 -#endif - -/* - * System IO Config - */ -#define CONFIG_SYS_SICRL SICRL_IRQ_CKS - -#define CONFIG_SYS_DDRCDR (\ - DDRCDR_EN | \ - DDRCDR_PZ_MAXZ | \ - DDRCDR_NZ_MAXZ | \ - DDRCDR_M_ODR) - -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f -#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \ - SDRAM_CFG_32_BE | \ - SDRAM_CFG_SREN | \ - SDRAM_CFG_HSE) - -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 -#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) -#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ - (0x200 << SDRAM_INTERVAL_REFINT_SHIFT)) - -#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \ - CSCONFIG_ODT_WR_CFG | \ - CSCONFIG_ROW_BIT_13 | \ - CSCONFIG_COL_BIT_10) - -#define CONFIG_SYS_DDR_MODE 0x47860242 -#define CONFIG_SYS_DDR_MODE2 0x8080c000 - -#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ - (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ - (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ - (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ - (0 << TIMING_CFG0_WWT_SHIFT) | \ - (0 << TIMING_CFG0_RRT_SHIFT) | \ - (0 << TIMING_CFG0_WRT_SHIFT) | \ - (0 << TIMING_CFG0_RWT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \ - (2 << TIMING_CFG1_WRTORD_SHIFT) | \ - (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ - (3 << TIMING_CFG1_WRREC_SHIFT) | \ - (7 << TIMING_CFG1_REFREC_SHIFT) | \ - (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ - (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ - (3 << TIMING_CFG1_PRETOACT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ - (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ - (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ - (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ - (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ - (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ - (5 << TIMING_CFG2_CPO_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 - -#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000 -#define CONFIG_SYS_KMBEC_FPGA_SIZE 128 - -/* EEprom support */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - -/* EEprom support */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - -/* - * Init Local Bus Memory Controller: - * - * Bank Bus Machine PortSz Size Device - * ---- --- ------- ------ ----- ------ - * 2 Local UPMA 16 bit 256MB APP1 - * 3 Local GPCM 16 bit 256MB APP2 - * - */ - - +#include "km/km-mpc83xx.h" +#include "km/km-mpc832x.h"
#define CONFIG_SYS_MAMR (MxMR_GPL_x4DIS | \ 0x0000c000 | \ diff --git a/include/configs/tuge1.h b/include/configs/tuge1.h index 01d8d6b3039..808538ef9d6 100644 --- a/include/configs/tuge1.h +++ b/include/configs/tuge1.h @@ -26,283 +26,10 @@ #define CONFIG_KM_BOARD_NAME "tuge1" #define CONFIG_HOSTNAME "tuge1"
-/* - * High Level Configuration Options - */ -#define CONFIG_QE /* Has QE */ -#define CONFIG_KM8321 /* Keymile PBEC8321 board specific */ - -#define CONFIG_KM_DEF_ARCH "arch=ppc_8xx\0" - /* include common defines/options for all Keymile boards */ #include "km/keymile-common.h" #include "km/km-powerpc.h" - -/* - * System Clock Setup - */ -#define CONFIG_83XX_CLKIN 66000000 -#define CONFIG_SYS_CLK_FREQ 66000000 -#define CONFIG_83XX_PCICLK 66000000 - -/* - * DDR Setup - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */ -#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */ - -#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ - DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) - -#define CFG_83XX_DDR_USES_CS0 - -/* - * Manually set up DDR parameters - */ -#define CONFIG_DDR_II -#define CONFIG_SYS_DDR_SIZE 2048 /* MB */ - -/* - * The reserved memory - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#define CONFIG_SYS_FLASH_BASE 0xF0000000 - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#endif - -/* Reserve 768 kB for Mon */ -#define CONFIG_SYS_MONITOR_LEN (768 * 1024) - -/* - * Initial RAM Base Address Setup - */ -#define CONFIG_SYS_INIT_RAM_LOCK -#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) - -/* - * Init Local Bus Memory Controller: - * - * Bank Bus Machine PortSz Size Device - * ---- --- ------- ------ ----- ------ - * 0 Local GPCM 16 bit 256MB FLASH - * 1 Local GPCM 8 bit 128MB GPIO/PIGGY - * - */ -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */ - - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } - -/* - * PRIO1/PIGGY on the local bus CS1 - */ - - -/* - * Serial Port - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) - -/* - * QE UEC ethernet configuration - */ -#define CONFIG_UEC_ETH -#define CONFIG_ETHPRIME "UEC0" - -#define CONFIG_UEC_ETH1 /* GETH1 */ -#define UEC_VERBOSE_DEBUG 1 - -#ifdef CONFIG_UEC_ETH1 -#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */ -#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ -#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17 -#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH -#define CONFIG_SYS_UEC1_PHY_ADDR 0 -#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII -#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 -#endif - -/* - * Environment - */ - -#ifndef CONFIG_SYS_RAMBOOT -#ifndef CONFIG_ENV_ADDR -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ - CONFIG_SYS_MONITOR_LEN) -#endif -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ -#ifndef CONFIG_ENV_OFFSET -#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN) -#endif - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -#else /* CFG_SYS_RAMBOOT */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) -#define CONFIG_ENV_SIZE 0x2000 -#endif /* CFG_SYS_RAMBOOT */ - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_NUM_I2C_BUSES 4 -#define CONFIG_SYS_I2C_MAX_HOPS 1 -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 200000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 200000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \ - {1, {I2C_NULL_HOP} } } - -#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/ - -#if defined(CONFIG_CMD_NAND) -#define CONFIG_NAND_KMETER1 -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE -#endif - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) - -/* - * Internal Definitions - */ -#define BOOTFLASH_START 0xF0000000 - -#define CONFIG_KM_CONSOLE_TTY "ttyS0" - -/* - * Environment Configuration - */ -#define CONFIG_ENV_OVERWRITE -#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ -#define CONFIG_KM_DEF_ENV "km-common=empty\0" -#endif - -#ifndef CONFIG_KM_DEF_ARCH -#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" -#endif - -#define CONFIG_EXTRA_ENV_SETTINGS \ - CONFIG_KM_DEF_ENV \ - CONFIG_KM_DEF_ARCH \ - "newenv=" \ - "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \ - "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \ - "unlock=yes\0" \ - "" - -#if defined(CONFIG_UEC_ETH) -#define CONFIG_HAS_ETH0 -#endif - -/* - * System IO Config - */ -#define CONFIG_SYS_SICRL SICRL_IRQ_CKS - -#define CONFIG_SYS_DDRCDR (\ - DDRCDR_EN | \ - DDRCDR_PZ_MAXZ | \ - DDRCDR_NZ_MAXZ | \ - DDRCDR_M_ODR) - -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f -#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \ - SDRAM_CFG_32_BE | \ - SDRAM_CFG_SREN | \ - SDRAM_CFG_HSE) - -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 -#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) -#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ - (0x200 << SDRAM_INTERVAL_REFINT_SHIFT)) - -#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \ - CSCONFIG_ODT_WR_CFG | \ - CSCONFIG_ROW_BIT_13 | \ - CSCONFIG_COL_BIT_10) - -#define CONFIG_SYS_DDR_MODE 0x47860242 -#define CONFIG_SYS_DDR_MODE2 0x8080c000 - -#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ - (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ - (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ - (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ - (0 << TIMING_CFG0_WWT_SHIFT) | \ - (0 << TIMING_CFG0_RRT_SHIFT) | \ - (0 << TIMING_CFG0_WRT_SHIFT) | \ - (0 << TIMING_CFG0_RWT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \ - (2 << TIMING_CFG1_WRTORD_SHIFT) | \ - (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ - (3 << TIMING_CFG1_WRREC_SHIFT) | \ - (7 << TIMING_CFG1_REFREC_SHIFT) | \ - (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ - (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ - (3 << TIMING_CFG1_PRETOACT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ - (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ - (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ - (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ - (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ - (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ - (5 << TIMING_CFG2_CPO_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 - -#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000 -#define CONFIG_SYS_KMBEC_FPGA_SIZE 128 - -/* EEprom support */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - -/* - * Init Local Bus Memory Controller: - * Device on board - * Bank Bus Machine PortSz Size TUDA1 TUXA1 TUGE1 KMSUPX4 KMOPTI2 - * ----------------------------------------------------------------------------- - * 2 Local GPCM 8 bit 256MB PAXG LPXF PAXI LPXF PAXE - * 3 Local GPCM 8 bit 256MB PINC3 PINC2 unused unused OPI2(16 bit) - * - * Device on board (continued) - * Bank Bus Machine PortSz Size KMTEPR2 - * ----------------------------------------------------------------------------- - * 2 Local GPCM 8 bit 256MB NVRAM - * 3 Local GPCM 8 bit 256MB TEP2 (16 bit) - */ - +#include "km/km-mpc83xx.h" +#include "km/km-mpc832x.h"
#endif /* __CONFIG_H */ diff --git a/include/configs/tuxx1.h b/include/configs/tuxx1.h index c1d06f00676..295e92d4a18 100644 --- a/include/configs/tuxx1.h +++ b/include/configs/tuxx1.h @@ -26,285 +26,11 @@ #define CONFIG_KM_BOARD_NAME "tuxx1" #define CONFIG_HOSTNAME "tuxx1"
-/* - * High Level Configuration Options - */ -#define CONFIG_QE /* Has QE */ -#define CONFIG_KM8321 /* Keymile PBEC8321 board specific */ - -#define CONFIG_KM_DEF_ARCH "arch=ppc_8xx\0" - /* include common defines/options for all Keymile boards */ #include "km/keymile-common.h" #include "km/km-powerpc.h" - -/* - * System Clock Setup - */ -#define CONFIG_83XX_CLKIN 66000000 -#define CONFIG_SYS_CLK_FREQ 66000000 -#define CONFIG_83XX_PCICLK 66000000 - -/* - * DDR Setup - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */ -#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */ - -#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ - DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) - -#define CFG_83XX_DDR_USES_CS0 - -/* - * Manually set up DDR parameters - */ -#define CONFIG_DDR_II -#define CONFIG_SYS_DDR_SIZE 2048 /* MB */ - -/* - * The reserved memory - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#define CONFIG_SYS_FLASH_BASE 0xF0000000 - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#endif - -/* Reserve 768 kB for Mon */ -#define CONFIG_SYS_MONITOR_LEN (768 * 1024) - -/* - * Initial RAM Base Address Setup - */ -#define CONFIG_SYS_INIT_RAM_LOCK -#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) - -/* - * Init Local Bus Memory Controller: - * - * Bank Bus Machine PortSz Size Device - * ---- --- ------- ------ ----- ------ - * 0 Local GPCM 16 bit 256MB FLASH - * 1 Local GPCM 8 bit 128MB GPIO/PIGGY - * - */ -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */ - - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } - -/* - * PRIO1/PIGGY on the local bus CS1 - */ - - -/* - * Serial Port - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) - -/* - * QE UEC ethernet configuration - */ -#define CONFIG_UEC_ETH -#define CONFIG_ETHPRIME "UEC0" - -#define CONFIG_UEC_ETH1 /* GETH1 */ -#define UEC_VERBOSE_DEBUG 1 - -#ifdef CONFIG_UEC_ETH1 -#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */ -#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ -#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17 -#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH -#define CONFIG_SYS_UEC1_PHY_ADDR 0 -#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII -#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 -#endif - -/* - * Environment - */ - -#ifndef CONFIG_SYS_RAMBOOT -#ifndef CONFIG_ENV_ADDR -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ - CONFIG_SYS_MONITOR_LEN) -#endif -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ -#ifndef CONFIG_ENV_OFFSET -#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN) -#endif - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -#else /* CFG_SYS_RAMBOOT */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) -#define CONFIG_ENV_SIZE 0x2000 -#endif /* CFG_SYS_RAMBOOT */ - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_NUM_I2C_BUSES 4 -#define CONFIG_SYS_I2C_MAX_HOPS 1 -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 200000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 200000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \ - {1, {I2C_NULL_HOP} } } - -#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/ - -#if defined(CONFIG_CMD_NAND) -#define CONFIG_NAND_KMETER1 -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE -#endif - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) - -/* - * Internal Definitions - */ -#define BOOTFLASH_START 0xF0000000 - -#define CONFIG_KM_CONSOLE_TTY "ttyS0" - -/* - * Environment Configuration - */ -#define CONFIG_ENV_OVERWRITE -#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ -#define CONFIG_KM_DEF_ENV "km-common=empty\0" -#endif - -#ifndef CONFIG_KM_DEF_ARCH -#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" -#endif - -#define CONFIG_EXTRA_ENV_SETTINGS \ - CONFIG_KM_DEF_ENV \ - CONFIG_KM_DEF_ARCH \ - "newenv=" \ - "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \ - "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \ - "unlock=yes\0" \ - "" - -#if defined(CONFIG_UEC_ETH) -#define CONFIG_HAS_ETH0 -#endif - -/* - * System IO Config - */ -#define CONFIG_SYS_SICRL SICRL_IRQ_CKS - -#define CONFIG_SYS_DDRCDR (\ - DDRCDR_EN | \ - DDRCDR_PZ_MAXZ | \ - DDRCDR_NZ_MAXZ | \ - DDRCDR_M_ODR) - -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f -#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \ - SDRAM_CFG_32_BE | \ - SDRAM_CFG_SREN | \ - SDRAM_CFG_HSE) - -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 -#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) -#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ - (0x200 << SDRAM_INTERVAL_REFINT_SHIFT)) - -#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \ - CSCONFIG_ODT_WR_CFG | \ - CSCONFIG_ROW_BIT_13 | \ - CSCONFIG_COL_BIT_10) - -#define CONFIG_SYS_DDR_MODE 0x47860242 -#define CONFIG_SYS_DDR_MODE2 0x8080c000 - -#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ - (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ - (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ - (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ - (0 << TIMING_CFG0_WWT_SHIFT) | \ - (0 << TIMING_CFG0_RRT_SHIFT) | \ - (0 << TIMING_CFG0_WRT_SHIFT) | \ - (0 << TIMING_CFG0_RWT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \ - (2 << TIMING_CFG1_WRTORD_SHIFT) | \ - (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ - (3 << TIMING_CFG1_WRREC_SHIFT) | \ - (7 << TIMING_CFG1_REFREC_SHIFT) | \ - (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ - (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ - (3 << TIMING_CFG1_PRETOACT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ - (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ - (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ - (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ - (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ - (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ - (5 << TIMING_CFG2_CPO_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 - -#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000 -#define CONFIG_SYS_KMBEC_FPGA_SIZE 128 - -/* EEprom support */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - -/* - * Init Local Bus Memory Controller: - * Device on board - * Bank Bus Machine PortSz Size TUDA1 TUXA1 TUGE1 KMSUPX4 KMOPTI2 - * ----------------------------------------------------------------------------- - * 2 Local GPCM 8 bit 256MB PAXG LPXF PAXI LPXF PAXE - * 3 Local GPCM 8 bit 256MB PINC3 PINC2 unused unused OPI2(16 bit) - * - * Device on board (continued) - * Bank Bus Machine PortSz Size KMTEPR2 - * ----------------------------------------------------------------------------- - * 2 Local GPCM 8 bit 256MB NVRAM - * 3 Local GPCM 8 bit 256MB TEP2 (16 bit) - */ - - +#include "km/km-mpc83xx.h" +#include "km/km-mpc832x.h"
#define CONFIG_SYS_MAMR (MxMR_GPL_x4DIS | \ 0x0000c000 | \