This is not available in kernel-land yet, but this initial set of definitions provides the info we need.
Signed-off-by: Simon Glass sjg@chromium.org --- arch/arm/dts/tegra20.dtsi | 80 +++++++++++++++++++++++++++++++++++++++++++++ 1 files changed, 80 insertions(+), 0 deletions(-)
diff --git a/arch/arm/dts/tegra20.dtsi b/arch/arm/dts/tegra20.dtsi index 65d7e6a..28d23da 100644 --- a/arch/arm/dts/tegra20.dtsi +++ b/arch/arm/dts/tegra20.dtsi @@ -143,5 +143,85 @@ reg = <0xc8000600 0x200>; interrupts = < 63 >; }; + +/* This table has USB timing parameters for each Oscillator frequency we + * support. There are four sets of values: + * + * 1. PLLU configuration information (reference clock is osc/clk_m and + * PLLU-FOs are fixed at 12MHz/60MHz/480MHz). + * + * Reference frequency 13.0MHz 19.2MHz 12.0MHz 26.0MHz + * ---------------------------------------------------------------------- + * DIVN 960 (0x3c0) 200 (0c8) 960 (3c0h) 960 (3c0) + * DIVM 13 (0d) 4 (04) 12 (0c) 26 (1a) + * Filter frequency (MHz) 1 4.8 6 2 + * CPCON 1100b 0011b 1100b 1100b + * LFCON0 0 0 0 0 + * + * 2. PLL CONFIGURATION & PARAMETERS for different clock generators: + * + * Reference frequency 13.0MHz 19.2MHz 12.0MHz 26.0MHz + * --------------------------------------------------------------------------- + * PLLU_ENABLE_DLY_COUNT 02 (0x02) 03 (03) 02 (02) 04 (04) + * PLLU_STABLE_COUNT 51 (33) 75 (4B) 47 (2F) 102 (66) + * PLL_ACTIVE_DLY_COUNT 05 (05) 06 (06) 04 (04) 09 (09) + * XTAL_FREQ_COUNT 127 (7F) 187 (BB) 118 (76) 254 (FE) + * + * 3. Debounce values IdDig, Avalid, Bvalid, VbusValid, VbusWakeUp, and + * SessEnd. Each of these signals have their own debouncer and for each of + * those one out of two debouncing times can be chosen (BIAS_DEBOUNCE_A or + * BIAS_DEBOUNCE_B). + * + * The values of DEBOUNCE_A and DEBOUNCE_B are calculated as follows: + * 0xffff -> No debouncing at all + * <n> ms = <n> *1000 / (1/19.2MHz) / 4 + * + * So to program a 1 ms debounce for BIAS_DEBOUNCE_A, we have: + * BIAS_DEBOUNCE_A[15:0] = 1000 * 19.2 / 4 = 4800 = 0x12c0 + * + * We need to use only DebounceA for BOOTROM. We don't need the DebounceB + * values, so we can keep those to default. + * + * a4. The 20 microsecond delay after bias cell operation. + * Reference frequency 13.0MHz 19.2MHz 12.0MHz 26.0MHz + */ + usbparams@0 { + compatible = "nvidia,tegra20-usbparams"; + osc-frequency = <13000000>; + /* DivN, DivM, DivP, CPCON, LFCON, Delays Debounce, Bias */ + params = <0x3c0 0x0d 0x00 0xc 0 0x02 0x33 0x05 0x7f 0x7ef4 5>; + }; + + usbparams@1 { + compatible = "nvidia,tegra20-usbparams"; + osc-frequency = <19200000>; + params = <0x0c8 0x04 0x00 0x3 0 0x03 0x4b 0x06 0xbb 0xbb80 7>; + }; + + usbparams@2 { + compatible = "nvidia,tegra20-usbparams"; + osc-frequency = <12000000>; + params = <0x3c0 0x0c 0x00 0xc 0 0x02 0x2f 0x04 0x76 0x7530 5>; + }; + + usbparams@3 { + compatible = "nvidia,tegra20-usbparams"; + osc-frequency = <26000000>; + params = <0x3c0 0x1a 0x00 0xc 0 0x04 0x66 0x09 0xfe 0xfde8 9>; + }; + + usb@0xc5008000 { + compatible = "nvidia,tegra20-usb"; + reg = <0xc5008000 0x8000>; + periph-id = <59>; // PERIPH_ID_USB3 + status = "disabled"; + }; + + usb@0xc5000000 { + compatible = "nvidia,tegra20-usb"; + reg = <0xc5000000 0x8000>; + periph-id = <22>; // PERIPH_ID_USBD + status = "disabled"; + }; };