These have not been converted to Generic Board, so should be removed. (See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada yamada.masahiro@socionext.com Cc: Tolunay Orkun torkun@nextio.com ---
arch/powerpc/cpu/ppc4xx/Kconfig | 8 -- board/csb272/Kconfig | 9 -- board/csb272/MAINTAINERS | 6 - board/csb272/Makefile | 9 -- board/csb272/csb272.c | 171 ------------------------ board/csb272/init.S | 196 ---------------------------- board/csb472/Kconfig | 9 -- board/csb472/MAINTAINERS | 6 - board/csb472/Makefile | 9 -- board/csb472/csb472.c | 138 -------------------- board/csb472/init.S | 192 --------------------------- configs/csb272_defconfig | 4 - configs/csb472_defconfig | 4 - doc/README.scrapyard | 1 + include/configs/csb272.h | 282 ---------------------------------------- include/configs/csb472.h | 281 --------------------------------------- 16 files changed, 1 insertion(+), 1324 deletions(-) delete mode 100644 board/csb272/Kconfig delete mode 100644 board/csb272/MAINTAINERS delete mode 100644 board/csb272/Makefile delete mode 100644 board/csb272/csb272.c delete mode 100644 board/csb272/init.S delete mode 100644 board/csb472/Kconfig delete mode 100644 board/csb472/MAINTAINERS delete mode 100644 board/csb472/Makefile delete mode 100644 board/csb472/csb472.c delete mode 100644 board/csb472/init.S delete mode 100644 configs/csb272_defconfig delete mode 100644 configs/csb472_defconfig delete mode 100644 include/configs/csb272.h delete mode 100644 include/configs/csb472.h
diff --git a/arch/powerpc/cpu/ppc4xx/Kconfig b/arch/powerpc/cpu/ppc4xx/Kconfig index e8c0ca0..c6bbe12 100644 --- a/arch/powerpc/cpu/ppc4xx/Kconfig +++ b/arch/powerpc/cpu/ppc4xx/Kconfig @@ -8,12 +8,6 @@ choice prompt "Target select" optional
-config TARGET_CSB272 - bool "Support csb272" - -config TARGET_CSB472 - bool "Support csb472" - config TARGET_LWMON5 bool "Support lwmon5" select SUPPORT_SPL @@ -176,8 +170,6 @@ source "board/amcc/yosemite/Kconfig" source "board/amcc/yucca/Kconfig" source "board/avnet/fx12mm/Kconfig" source "board/avnet/v5fx30teval/Kconfig" -source "board/csb272/Kconfig" -source "board/csb472/Kconfig" source "board/esd/cpci2dp/Kconfig" source "board/esd/cpci405/Kconfig" source "board/esd/plu405/Kconfig" diff --git a/board/csb272/Kconfig b/board/csb272/Kconfig deleted file mode 100644 index eed04f0..0000000 --- a/board/csb272/Kconfig +++ /dev/null @@ -1,9 +0,0 @@ -if TARGET_CSB272 - -config SYS_BOARD - default "csb272" - -config SYS_CONFIG_NAME - default "csb272" - -endif diff --git a/board/csb272/MAINTAINERS b/board/csb272/MAINTAINERS deleted file mode 100644 index 4bc95ea..0000000 --- a/board/csb272/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -CSB272 BOARD -M: Tolunay Orkun torkun@nextio.com -S: Maintained -F: board/csb272/ -F: include/configs/csb272.h -F: configs/csb272_defconfig diff --git a/board/csb272/Makefile b/board/csb272/Makefile deleted file mode 100644 index 36ec9b6..0000000 --- a/board/csb272/Makefile +++ /dev/null @@ -1,9 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y = csb272.o -obj-y += init.o diff --git a/board/csb272/csb272.c b/board/csb272/csb272.c deleted file mode 100644 index dc2c950..0000000 --- a/board/csb272/csb272.c +++ /dev/null @@ -1,171 +0,0 @@ -/* - * (C) Copyright 2004 - * Tolunay Orkun, Nextio Inc., torkun@nextio.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <asm/processor.h> -#include <i2c.h> -#include <miiphy.h> -#include <asm/ppc4xx-emac.h> - -void sdram_init(void); - -/* - * Configuration data for AMIS FS6377-01 Programmable 3-PLL Clock Generator - * - * CLKA output => Epson LCD Controller - * CLKB output => Not Connected - * CLKC output => Ethernet - * CLKD output => UART external clock - * - * Note: these values are obtained from device after init by micromonitor -*/ -uchar pll_fs6377_regs[16] = { - 0x28, 0xef, 0x53, 0x03, 0x4b, 0x80, 0x32, 0x80, - 0x94, 0x32, 0x80, 0xd4, 0x56, 0xf6, 0xf6, 0xe0 }; - -/* - * pll_init: Initialize AMIS IC FS6377-01 PLL - * - * PLL supplies Epson LCD Clock, Ethernet Clock and UART external clock - * - */ -int pll_init(void) -{ - i2c_set_bus_num(0); - - return i2c_write(CONFIG_SYS_I2C_PLL_ADDR, 0, 1, - (uchar *) pll_fs6377_regs, sizeof(pll_fs6377_regs)); -} - -/* - * board_early_init_f: do early board initialization - * - */ -int board_early_init_f(void) -{ - /* initialize PLL so UART, LCD, Ethernet clocked at correctly */ - (void) get_clocks(); - pll_init(); - - /*-------------------------------------------------------------------------+ - | Interrupt controller setup for the Walnut board. - | Note: IRQ 0-15 405GP internally generated; active high; level sensitive - | IRQ 16 405GP internally generated; active low; level sensitive - | IRQ 17-24 RESERVED - | IRQ 25 (EXT IRQ 0) FPGA; active high; level sensitive - | IRQ 26 (EXT IRQ 1) SMI; active high; level sensitive - | IRQ 27 (EXT IRQ 2) Not Used - | IRQ 28 (EXT IRQ 3) PCI SLOT 3; active low; level sensitive - | IRQ 29 (EXT IRQ 4) PCI SLOT 2; active low; level sensitive - | IRQ 30 (EXT IRQ 5) PCI SLOT 1; active low; level sensitive - | IRQ 31 (EXT IRQ 6) PCI SLOT 0; active low; level sensitive - | Note for Walnut board: - | An interrupt taken for the FPGA (IRQ 25) indicates that either - | the Mouse, Keyboard, IRDA, or External Expansion caused the - | interrupt. The FPGA must be read to determine which device - | caused the interrupt. The default setting of the FPGA clears - | - +-------------------------------------------------------------------------*/ - - mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */ - mtdcr (UIC0ER, 0x00000000); /* disable all ints */ - mtdcr (UIC0CR, 0x00000000); /* set all to be non-critical */ - mtdcr (UIC0PR, 0xFFFFFF83); /* set int polarities */ - mtdcr (UIC0TR, 0x10000000); /* set int trigger levels */ - mtdcr (UIC0VCR, 0x00000001); /* set vect base=0,INT0 highest priority */ - mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */ - - mtebc (EBC0_CFG, 0xa8400000); /* EBC always driven */ - - return 0; /* success */ -} - -/* - * checkboard: identify/verify the board we are running - * - * Remark: we just assume it is correct board here! - * - */ -int checkboard(void) -{ - printf("BOARD: Cogent CSB272\n"); - - return 0; /* success */ -} - -/* - * initram: Determine the size of mounted DRAM - * - * Size is determined by reading SDRAM configuration registers as - * configured by initialization code - * - */ -phys_size_t initdram (int board_type) -{ - ulong tot_size; - ulong bank_size; - ulong tmp; - - /* - * ToDo: Move the asm init routine sdram_init() to this C file, - * or even better use some common ppc4xx code available - * in arch/powerpc/cpu/ppc4xx - */ - sdram_init(); - - tot_size = 0; - - mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR); - tmp = mfdcr (SDRAM0_CFGDATA); - if (tmp & 0x00000001) { - bank_size = 0x00400000 << ((tmp >> 17) & 0x7); - tot_size += bank_size; - } - - mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR); - tmp = mfdcr (SDRAM0_CFGDATA); - if (tmp & 0x00000001) { - bank_size = 0x00400000 << ((tmp >> 17) & 0x7); - tot_size += bank_size; - } - - mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR); - tmp = mfdcr (SDRAM0_CFGDATA); - if (tmp & 0x00000001) { - bank_size = 0x00400000 << ((tmp >> 17) & 0x7); - tot_size += bank_size; - } - - mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR); - tmp = mfdcr (SDRAM0_CFGDATA); - if (tmp & 0x00000001) { - bank_size = 0x00400000 << ((tmp >> 17) & 0x7); - tot_size += bank_size; - } - - return tot_size; -} - -/* - * last_stage_init: final configurations (such as PHY etc) - * - */ -int last_stage_init(void) -{ - /* initialize the PHY */ - miiphy_reset("ppc_4xx_eth0", CONFIG_PHY_ADDR); - - /* AUTO neg */ - miiphy_write("ppc_4xx_eth0", CONFIG_PHY_ADDR, MII_BMCR, - BMCR_ANENABLE | BMCR_ANRESTART); - - /* LEDs */ - miiphy_write("ppc_4xx_eth0", CONFIG_PHY_ADDR, MII_NWAYTEST, 0x0d08); - - - return 0; /* success */ -} diff --git a/board/csb272/init.S b/board/csb272/init.S deleted file mode 100644 index bf1d986..0000000 --- a/board/csb272/init.S +++ /dev/null @@ -1,196 +0,0 @@ -/* - * SPDX-License-Identifier: GPL-2.0 IBM-pibs - */ -#include <config.h> -#include <asm/ppc4xx.h> - -#include <ppc_asm.tmpl> -#include <ppc_defs.h> - -#include <asm/cache.h> -#include <asm/mmu.h> - -#define LI32(reg,val) \ - addis reg,0,val@h;\ - ori reg,reg,val@l - -#define WDCR_EBC(reg,val) \ - addi r4,0,reg;\ - mtdcr EBC0_CFGADDR,r4;\ - addis r4,0,val@h;\ - ori r4,r4,val@l;\ - mtdcr EBC0_CFGDATA,r4 - -#define WDCR_SDRAM(reg,val) \ - addi r4,0,reg;\ - mtdcr SDRAM0_CFGADDR,r4;\ - addis r4,0,val@h;\ - ori r4,r4,val@l;\ - mtdcr SDRAM0_CFGDATA,r4 - -/****************************************************************************** - * Function: ext_bus_cntlr_init - * - * Description: Configures EBC Controller and a few basic chip selects. - * - * CS0 is setup to get the Boot Flash out of the addresss range - * so that we may setup a stack. CS7 is setup so that we can - * access and reset the hardware watchdog. - * - * IMPORTANT: For pass1 this code must run from - * cache since you can not reliably change a peripheral banks - * timing register (pbxap) while running code from that bank. - * For ex., since we are running from ROM on bank 0, we can NOT - * execute the code that modifies bank 0 timings from ROM, so - * we run it from cache. - * - * Notes: Does NOT use the stack. - *****************************************************************************/ - .section ".text" - .align 2 - .globl ext_bus_cntlr_init - .type ext_bus_cntlr_init, @function -ext_bus_cntlr_init: - mflr r0 - /******************************************************************** - * Prefetch entire ext_bus_cntrl_init function into the icache. - * This is necessary because we are going to change the same CS we - * are executing from. Otherwise a CPU lockup may occur. - *******************************************************************/ - bl ..getAddr -..getAddr: - mflr r3 /* get address of ..getAddr */ - - /* Calculate number of cache lines for this function */ - addi r4, 0, (((.Lfe0 - ..getAddr) / CONFIG_SYS_CACHELINE_SIZE) + 2) - mtctr r4 -..ebcloop: - icbt r0, r3 /* prefetch cache line for addr in r3*/ - addi r3, r3, CONFIG_SYS_CACHELINE_SIZE /* move to next cache line */ - bdnz ..ebcloop /* continue for $CTR cache lines */ - - /******************************************************************** - * Delay to ensure all accesses to ROM are complete before changing - * bank 0 timings. 200usec should be enough. - * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles. - *******************************************************************/ - addis r3, 0, 0x0 - ori r3, r3, 0xA000 /* wait 200us from reset */ - mtctr r3 -..spinlp: - bdnz ..spinlp /* spin loop */ - - /******************************************************************** - * SETUP CPC0_CR0 - *******************************************************************/ - LI32(r4, 0x007000c0) - mtdcr CPC0_CR0, r4 - - /******************************************************************** - * Setup CPC0_CR1: Change PCIINT signal to PerWE - *******************************************************************/ - mfdcr r4, CPC0_CR1 - ori r4, r4, 0x4000 - mtdcr CPC0_CR1, r4 - - /******************************************************************** - * Setup External Bus Controller (EBC). - *******************************************************************/ - WDCR_EBC(EBC0_CFG, 0xd84c0000) - /******************************************************************** - * Memory Bank 0 (Intel 28F128J3 Flash) initialization - *******************************************************************/ - /*WDCR_EBC(PB1AP, 0x02869200)*/ - WDCR_EBC(PB1AP, 0x07869200) - WDCR_EBC(PB0CR, 0xfe0bc000) - /******************************************************************** - * Memory Bank 1 (Holtek HT6542B PS/2) initialization - *******************************************************************/ - WDCR_EBC(PB1AP, 0x1f869200) - WDCR_EBC(PB1CR, 0xf0818000) - /******************************************************************** - * Memory Bank 2 (Epson S1D13506) initialization - *******************************************************************/ - WDCR_EBC(PB2AP, 0x05860300) - WDCR_EBC(PB2CR, 0xf045a000) - /******************************************************************** - * Memory Bank 3 (Philips SJA1000 CAN Controllers) initialization - *******************************************************************/ - WDCR_EBC(PB3AP, 0x0387d200) - WDCR_EBC(PB3CR, 0xf021c000) - /******************************************************************** - * Memory Bank 4-7 (Unused) initialization - *******************************************************************/ - WDCR_EBC(PB4AP, 0) - WDCR_EBC(PB4CR, 0) - WDCR_EBC(PB5AP, 0) - WDCR_EBC(PB5CR, 0) - WDCR_EBC(PB6AP, 0) - WDCR_EBC(PB6CR, 0) - WDCR_EBC(PB7AP, 0) - WDCR_EBC(PB7CR, 0) - - /* We are all done */ - mtlr r0 /* Restore link register */ - blr /* Return to calling function */ -.Lfe0: .size ext_bus_cntlr_init,.Lfe0-ext_bus_cntlr_init -/* end ext_bus_cntlr_init() */ - -/****************************************************************************** - * Function: sdram_init - * - * Description: Configures SDRAM memory banks. - * - * Notes: Does NOT use the stack. - *****************************************************************************/ - .section ".text" - .align 2 - .globl sdram_init - .type sdram_init, @function -sdram_init: - - /* - * Disable memory controller to allow - * values to be changed. - */ - WDCR_SDRAM(SDRAM0_CFG, 0x00000000) - - /* - * Configure Memory Banks - */ - WDCR_SDRAM(SDRAM0_B0CR, 0x00084001) - WDCR_SDRAM(SDRAM0_B1CR, 0x00000000) - WDCR_SDRAM(SDRAM0_B2CR, 0x00000000) - WDCR_SDRAM(SDRAM0_B3CR, 0x00000000) - - /* - * Set up SDTR1 (SDRAM Timing Register) - */ - WDCR_SDRAM(SDRAM0_TR, 0x00854009) - - /* - * Set RTR (Refresh Timing Register) - */ - WDCR_SDRAM(SDRAM0_RTR, 0x10000000) - /* WDCR_SDRAM(SDRAM0_RTR, 0x05f00000) */ - - /******************************************************************** - * Delay to ensure 200usec have elapsed since reset. Assume worst - * case that the core is running 200Mhz: - * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles - *******************************************************************/ - addis r3, 0, 0x0000 - ori r3, r3, 0xA000 /* Wait >200us from reset */ - mtctr r3 -..spinlp2: - bdnz ..spinlp2 /* spin loop */ - - /******************************************************************** - * Set memory controller options reg, MCOPT1. - *******************************************************************/ - WDCR_SDRAM(SDRAM0_CFG,0x80800000) - -..sdri_done: - blr /* Return to calling function */ -.Lfe1: .size sdram_init,.Lfe1-sdram_init -/* end sdram_init() */ diff --git a/board/csb472/Kconfig b/board/csb472/Kconfig deleted file mode 100644 index 53b1e7a..0000000 --- a/board/csb472/Kconfig +++ /dev/null @@ -1,9 +0,0 @@ -if TARGET_CSB472 - -config SYS_BOARD - default "csb472" - -config SYS_CONFIG_NAME - default "csb472" - -endif diff --git a/board/csb472/MAINTAINERS b/board/csb472/MAINTAINERS deleted file mode 100644 index 25041ed..0000000 --- a/board/csb472/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -CSB472 BOARD -M: Tolunay Orkun torkun@nextio.com -S: Maintained -F: board/csb472/ -F: include/configs/csb472.h -F: configs/csb472_defconfig diff --git a/board/csb472/Makefile b/board/csb472/Makefile deleted file mode 100644 index 5f7e8b5..0000000 --- a/board/csb472/Makefile +++ /dev/null @@ -1,9 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y = csb472.o -obj-y += init.o diff --git a/board/csb472/csb472.c b/board/csb472/csb472.c deleted file mode 100644 index b1de18c..0000000 --- a/board/csb472/csb472.c +++ /dev/null @@ -1,138 +0,0 @@ -/* - * (C) Copyright 2004 - * Tolunay Orkun, Nextio Inc., torkun@nextio.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <asm/processor.h> -#include <i2c.h> -#include <miiphy.h> -#include <asm/ppc4xx-emac.h> - -void sdram_init(void); - -/* - * board_early_init_f: do early board initialization - * - */ -int board_early_init_f(void) -{ - /*-------------------------------------------------------------------------+ - | Interrupt controller setup for the Walnut board. - | Note: IRQ 0-15 405GP internally generated; active high; level sensitive - | IRQ 16 405GP internally generated; active low; level sensitive - | IRQ 17-24 RESERVED - | IRQ 25 (EXT IRQ 0) FPGA; active high; level sensitive - | IRQ 26 (EXT IRQ 1) SMI; active high; level sensitive - | IRQ 27 (EXT IRQ 2) Not Used - | IRQ 28 (EXT IRQ 3) PCI SLOT 3; active low; level sensitive - | IRQ 29 (EXT IRQ 4) PCI SLOT 2; active low; level sensitive - | IRQ 30 (EXT IRQ 5) PCI SLOT 1; active low; level sensitive - | IRQ 31 (EXT IRQ 6) PCI SLOT 0; active low; level sensitive - | Note for Walnut board: - | An interrupt taken for the FPGA (IRQ 25) indicates that either - | the Mouse, Keyboard, IRDA, or External Expansion caused the - | interrupt. The FPGA must be read to determine which device - | caused the interrupt. The default setting of the FPGA clears - | - +-------------------------------------------------------------------------*/ - - mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */ - mtdcr (UIC0ER, 0x00000000); /* disable all ints */ - mtdcr (UIC0CR, 0x00000000); /* set all to be non-critical */ - mtdcr (UIC0PR, 0xFFFFFF83); /* set int polarities */ - mtdcr (UIC0TR, 0x10000000); /* set int trigger levels */ - mtdcr (UIC0VCR, 0x00000001); /* set vect base=0,INT0 highest priority */ - mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */ - - mtebc (EBC0_CFG, 0xa8400000); /* EBC always driven */ - - return 0; /* success */ -} - -/* - * checkboard: identify/verify the board we are running - * - * Remark: we just assume it is correct board here! - * - */ -int checkboard(void) -{ - printf("BOARD: Cogent CSB472\n"); - - return 0; /* success */ -} - -/* - * initram: Determine the size of mounted DRAM - * - * Size is determined by reading SDRAM configuration registers as - * configured by initialization code - * - */ -phys_size_t initdram (int board_type) -{ - ulong tot_size; - ulong bank_size; - ulong tmp; - - /* - * ToDo: Move the asm init routine sdram_init() to this C file, - * or even better use some common ppc4xx code available - * in arch/powerpc/cpu/ppc4xx - */ - sdram_init(); - - tot_size = 0; - - mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR); - tmp = mfdcr (SDRAM0_CFGDATA); - if (tmp & 0x00000001) { - bank_size = 0x00400000 << ((tmp >> 17) & 0x7); - tot_size += bank_size; - } - - mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR); - tmp = mfdcr (SDRAM0_CFGDATA); - if (tmp & 0x00000001) { - bank_size = 0x00400000 << ((tmp >> 17) & 0x7); - tot_size += bank_size; - } - - mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR); - tmp = mfdcr (SDRAM0_CFGDATA); - if (tmp & 0x00000001) { - bank_size = 0x00400000 << ((tmp >> 17) & 0x7); - tot_size += bank_size; - } - - mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR); - tmp = mfdcr (SDRAM0_CFGDATA); - if (tmp & 0x00000001) { - bank_size = 0x00400000 << ((tmp >> 17) & 0x7); - tot_size += bank_size; - } - - return tot_size; -} - -/* - * last_stage_init: final configurations (such as PHY etc) - * - */ -int last_stage_init(void) -{ - /* initialize the PHY */ - miiphy_reset("ppc_4xx_eth0", CONFIG_PHY_ADDR); - - /* AUTO neg */ - miiphy_write("ppc_4xx_eth0", CONFIG_PHY_ADDR, MII_BMCR, - BMCR_ANENABLE | BMCR_ANRESTART); - - /* LEDs */ - miiphy_write("ppc_4xx_eth0", CONFIG_PHY_ADDR, MII_NWAYTEST, 0x0d08); - - return 0; /* success */ -} diff --git a/board/csb472/init.S b/board/csb472/init.S deleted file mode 100644 index 7383a70..0000000 --- a/board/csb472/init.S +++ /dev/null @@ -1,192 +0,0 @@ -/* - * SPDX-License-Identifier: GPL-2.0 IBM-pibs - */ -#include <config.h> -#include <asm/ppc4xx.h> - -#include <ppc_asm.tmpl> -#include <ppc_defs.h> - -#include <asm/cache.h> -#include <asm/mmu.h> - -#define LI32(reg,val) \ - addis reg,0,val@h;\ - ori reg,reg,val@l - -#define WDCR_EBC(reg,val) \ - addi r4,0,reg;\ - mtdcr EBC0_CFGADDR,r4;\ - addis r4,0,val@h;\ - ori r4,r4,val@l;\ - mtdcr EBC0_CFGDATA,r4 - -#define WDCR_SDRAM(reg,val) \ - addi r4,0,reg;\ - mtdcr SDRAM0_CFGADDR,r4;\ - addis r4,0,val@h;\ - ori r4,r4,val@l;\ - mtdcr SDRAM0_CFGDATA,r4 - -/****************************************************************************** - * Function: ext_bus_cntlr_init - * - * Description: Configures EBC Controller and a few basic chip selects. - * - * CS0 is setup to get the Boot Flash out of the addresss range - * so that we may setup a stack. CS7 is setup so that we can - * access and reset the hardware watchdog. - * - * IMPORTANT: For pass1 this code must run from - * cache since you can not reliably change a peripheral banks - * timing register (pbxap) while running code from that bank. - * For ex., since we are running from ROM on bank 0, we can NOT - * execute the code that modifies bank 0 timings from ROM, so - * we run it from cache. - * - * Notes: Does NOT use the stack. - *****************************************************************************/ - .section ".text" - .align 2 - .globl ext_bus_cntlr_init - .type ext_bus_cntlr_init, @function -ext_bus_cntlr_init: - mflr r0 - /******************************************************************** - * Prefetch entire ext_bus_cntrl_init function into the icache. - * This is necessary because we are going to change the same CS we - * are executing from. Otherwise a CPU lockup may occur. - *******************************************************************/ - bl ..getAddr -..getAddr: - mflr r3 /* get address of ..getAddr */ - - /* Calculate number of cache lines for this function */ - addi r4, 0, (((.Lfe0 - ..getAddr) / CONFIG_SYS_CACHELINE_SIZE) + 2) - mtctr r4 -..ebcloop: - icbt r0, r3 /* prefetch cache line for addr in r3*/ - addi r3, r3, CONFIG_SYS_CACHELINE_SIZE /* move to next cache line */ - bdnz ..ebcloop /* continue for $CTR cache lines */ - - /******************************************************************** - * Delay to ensure all accesses to ROM are complete before changing - * bank 0 timings. 200usec should be enough. - * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles. - *******************************************************************/ - addis r3, 0, 0x0 - ori r3, r3, 0xA000 /* wait 200us from reset */ - mtctr r3 -..spinlp: - bdnz ..spinlp /* spin loop */ - - /******************************************************************** - * SETUP CPC0_CR0 - *******************************************************************/ - LI32(r4, 0x00c01030) - mtdcr CPC0_CR0, r4 - - /******************************************************************** - * Setup CPC0_CR1: Change PCIINT signal to PerWE - *******************************************************************/ - mfdcr r4, CPC0_CR1 - ori r4, r4, 0x4000 - mtdcr CPC0_CR1, r4 - - /******************************************************************** - * Setup External Bus Controller (EBC). - *******************************************************************/ - WDCR_EBC(EBC0_CFG, 0xd84c0000) - /******************************************************************** - * Memory Bank 0 (Intel 28F640J3 Flash) initialization - *******************************************************************/ - /*WDCR_EBC(PB1AP, 0x03055200)*/ - /*WDCR_EBC(PB1AP, 0x04055200)*/ - WDCR_EBC(PB1AP, 0x08055200) - WDCR_EBC(PB0CR, 0xff87a000) - /******************************************************************** - * Memory Bank 3 (Xilinx XC95144 CPLD) initialization - *******************************************************************/ - /*WDCR_EBC(PB3AP, 0x07869200)*/ - WDCR_EBC(PB3AP, 0x04055200) - WDCR_EBC(PB3CR, 0xf081c000) - /******************************************************************** - * Memory Bank 1,2,4-7 (Unused) initialization - *******************************************************************/ - WDCR_EBC(PB1AP, 0) - WDCR_EBC(PB1CR, 0) - WDCR_EBC(PB2AP, 0) - WDCR_EBC(PB2CR, 0) - WDCR_EBC(PB4AP, 0) - WDCR_EBC(PB4CR, 0) - WDCR_EBC(PB5AP, 0) - WDCR_EBC(PB5CR, 0) - WDCR_EBC(PB6AP, 0) - WDCR_EBC(PB6CR, 0) - WDCR_EBC(PB7AP, 0) - WDCR_EBC(PB7CR, 0) - - /* We are all done */ - mtlr r0 /* Restore link register */ - blr /* Return to calling function */ -.Lfe0: .size ext_bus_cntlr_init,.Lfe0-ext_bus_cntlr_init -/* end ext_bus_cntlr_init() */ - -/****************************************************************************** - * Function: sdram_init - * - * Description: Configures SDRAM memory banks. - * - * Notes: Does NOT use the stack. - *****************************************************************************/ - .section ".text" - .align 2 - .globl sdram_init - .type sdram_init, @function -sdram_init: - - /* - * Disable memory controller to allow - * values to be changed. - */ - WDCR_SDRAM(SDRAM0_CFG, 0x00000000) - - /* - * Configure Memory Banks - */ - WDCR_SDRAM(SDRAM0_B0CR, 0x00062001) - WDCR_SDRAM(SDRAM0_B1CR, 0x00000000) - WDCR_SDRAM(SDRAM0_B2CR, 0x00000000) - WDCR_SDRAM(SDRAM0_B3CR, 0x00000000) - - /* - * Set up SDTR1 (SDRAM Timing Register) - */ - WDCR_SDRAM(SDRAM0_TR, 0x00854009) - - /* - * Set RTR (Refresh Timing Register) - */ - WDCR_SDRAM(SDRAM0_RTR, 0x10000000) - /* WDCR_SDRAM(SDRAM0_RTR, 0x05f00000) */ - - /******************************************************************** - * Delay to ensure 200usec have elapsed since reset. Assume worst - * case that the core is running 200Mhz: - * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles - *******************************************************************/ - addis r3, 0, 0x0000 - ori r3, r3, 0xA000 /* Wait >200us from reset */ - mtctr r3 -..spinlp2: - bdnz ..spinlp2 /* spin loop */ - - /******************************************************************** - * Set memory controller options reg, MCOPT1. - *******************************************************************/ - WDCR_SDRAM(SDRAM0_CFG,0x80800000) - -..sdri_done: - blr /* Return to calling function */ -.Lfe1: .size sdram_init,.Lfe1-sdram_init -/* end sdram_init() */ diff --git a/configs/csb272_defconfig b/configs/csb272_defconfig deleted file mode 100644 index c9cc680..0000000 --- a/configs/csb272_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_PPC=y -CONFIG_4xx=y -CONFIG_TARGET_CSB272=y -# CONFIG_CMD_SETEXPR is not set diff --git a/configs/csb472_defconfig b/configs/csb472_defconfig deleted file mode 100644 index e46b965..0000000 --- a/configs/csb472_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_PPC=y -CONFIG_4xx=y -CONFIG_TARGET_CSB472=y -# CONFIG_CMD_SETEXPR is not set diff --git a/doc/README.scrapyard b/doc/README.scrapyard index cdb2b6e..87e2b35 100644 --- a/doc/README.scrapyard +++ b/doc/README.scrapyard @@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order.
Board Arch CPU Commit Removed Last known maintainer/contact ================================================================================================= +csb272/csb472 powerpc ppc4xx - - Tolunay Orkun torkun@nextio.com alpr powerpc ppc4xx - - Stefan Roese sr@denx.de cam_enc_4xx arm arm926ejs 8d775763 2015-08-20 Heiko Schocher hs@denx.de atstk1003 avr32 - e5354b8a 2015-06-10 Haavard Skinnemoen haavard.skinnemoen@atmel.com diff --git a/include/configs/csb272.h b/include/configs/csb272.h deleted file mode 100644 index 71cb5df..0000000 --- a/include/configs/csb272.h +++ /dev/null @@ -1,282 +0,0 @@ -/* - * (C) Copyright 2004 - * Tolunay Orkun, Nextio Inc., torkun@nextio.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_405GP 1 /* This is a PPC405GP CPU */ -#define CONFIG_CSB272 1 /* on a Cogent CSB272 board */ -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f() */ -#define CONFIG_LAST_STAGE_INIT 1 /* Call last_stage_init() */ -#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */ - -#define CONFIG_SYS_TEXT_BASE 0xFFFC0000 - -/* - * OS Bootstrap configuration - * - */ - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 3 /* autoboot after X seconds */ -#endif - -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check keypress when bootdelay = 0 */ - -#if 1 -#undef CONFIG_BOOTARGS -#define CONFIG_BOOTCOMMAND \ - "setenv bootargs console=ttyS0,38400 debug " \ - "root=/dev/ram rw ramdisk_size=4096 " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \ - "bootm fe000000 fe100000" -#endif - -#if 0 -#undef CONFIG_BOOTARGS -#define CONFIG_BOOTCOMMAND \ - "bootp; " \ - "setenv bootargs console=ttyS0,38400 debug " \ - "root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \ - "bootm" -#endif - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_DNS2 - - -/* - * Command line configuration. - */ -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_BEDBUG -#define CONFIG_CMD_ELF -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_I2C -#define CONFIG_CMD_PCI -#define CONFIG_CMD_DATE -#define CONFIG_CMD_MII -#define CONFIG_CMD_PING -#define CONFIG_CMD_DHCP - - -/* - * Serial download configuration - * - */ -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * KGDB Configuration - * - */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/* - * Miscellaneous configurable options - * - */ -#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ - -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_info (bd_t) */ -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * watchdog configuration - * - */ -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * UART configuration - * - */ -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() - -#define CONFIG_SYS_EXT_SERIAL_CLOCK 3868400 /* use external serial clock */ -#undef CONFIG_SYS_BASE_BAUD -#define CONFIG_BAUDRATE 38400 /* Default baud rate */ -#define CONFIG_SYS_BAUDRATE_TABLE \ - { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400 } - -/* - * I2C configuration - * - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F /* I2C slave address */ - -/* - * MII PHY configuration - * - */ -#define CONFIG_PPC4xx_EMAC -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 0 /* PHY address */ -#define CONFIG_PHY_CMD_DELAY 40 /* PHY COMMAND delay */ - /* 32usec min. for LXT971A */ -#define CONFIG_PHY_RESET_DELAY 300 /* PHY RESET recovery delay */ - -/* - * RTC configuration - * - * Note that DS1307 RTC is limited to 100Khz I2C bus. - * - */ -#define CONFIG_RTC_DS1307 /* Use Dallas 1307 RTC */ - -/* - * PCI stuff - * - */ -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ -#define CONFIG_PCI_PNP /* do pci plug-and-play */ - /* resource configuration */ -#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ -#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/ - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */ -#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ -#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */ -#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */ -#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ - -/* - * IDE stuff - * - */ -#undef CONFIG_IDE_PCMCIA /* no pcmcia interface required */ -#undef CONFIG_IDE_LED /* no led for ide supported */ -#undef CONFIG_IDE_RESET /* no reset for ide supported */ - -/* - * Environment configuration - * - */ -#define CONFIG_ENV_IS_IN_FLASH 1 /* environment is in FLASH */ -#undef CONFIG_ENV_IS_IN_NVRAM -#undef CONFIG_ENV_IS_IN_EEPROM - -/* - * General Memory organization - * - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xFE000000 -#define CONFIG_SYS_FLASH_SIZE 0x02000000 -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 KB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 KB for malloc() */ - -#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_RAMSTART -#endif - -#if defined(CONFIG_ENV_IS_IN_FLASH) -#define CONFIG_ENV_IN_OWN_SECTOR 1 /* Give Environment own sector */ -#define CONFIG_ENV_ADDR 0xFFF00000 /* Address of Environment Sector */ -#define CONFIG_ENV_SIZE 0x00001000 /* Size of Environment */ -#define CONFIG_ENV_SECT_SIZE 0x00040000 /* Size of Environment Sector */ -#endif - -/* - * FLASH Device configuration - * - */ -#define CONFIG_SYS_FLASH_CFI 1 /* flash is CFI conformant */ -#define CONFIG_FLASH_CFI_DRIVER 1 /* use common cfi driver */ -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max # of memory banks */ -#define CONFIG_SYS_FLASH_INCREMENT 0 /* there is only one bank */ -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max # of sectors on one chip */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* hardware flash protection */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } - -/* - * On Chip Memory location/size - * - */ -#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 -#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 - -/* - * Global info and initial stack - * - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of on-chip SRAM */ -#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* - * Miscellaneous board specific definitions - * - */ -#define CONFIG_SYS_I2C_PLL_ADDR 0x58 /* I2C address of AMIS FS6377-01 PLL */ -#define CONFIG_I2CFAST 1 /* enable "i2cfast" env. setting */ - -#endif /* __CONFIG_H */ diff --git a/include/configs/csb472.h b/include/configs/csb472.h deleted file mode 100644 index 5bd3867..0000000 --- a/include/configs/csb472.h +++ /dev/null @@ -1,281 +0,0 @@ -/* - * (C) Copyright 2004 - * Tolunay Orkun, Nextio Inc., torkun@nextio.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_405GP 1 /* This is a PPC405GP CPU */ -#define CONFIG_CSB472 1 /* on a Cogent CSB472 board */ -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f() */ -#define CONFIG_LAST_STAGE_INIT 1 /* Call last_stage_init() */ -#define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */ - -#define CONFIG_SYS_TEXT_BASE 0xFFFC0000 - -/* - * OS Bootstrap configuration - * - */ - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 3 /* autoboot after X seconds */ -#endif - -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check keypress when bootdelay = 0 */ - -#if 1 -#undef CONFIG_BOOTARGS -#define CONFIG_BOOTCOMMAND \ - "setenv bootargs console=ttyS0,38400 debug " \ - "root=/dev/ram rw ramdisk_size=4096 " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \ - "bootm ff800000 ff900000" -#endif - -#if 0 -#undef CONFIG_BOOTARGS -#define CONFIG_BOOTCOMMAND \ - "bootp; " \ - "setenv bootargs console=ttyS0,38400 debug " \ - "root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \ - "bootm" -#endif - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_DNS2 - - -/* - * Command line configuration. - */ -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_BEDBUG -#define CONFIG_CMD_ELF -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_I2C -#define CONFIG_CMD_PCI -#define CONFIG_CMD_DATE -#define CONFIG_CMD_MII -#define CONFIG_CMD_PING -#define CONFIG_CMD_DHCP - -/* - * Serial download configuration - * - */ -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * KGDB Configuration - * - */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/* - * Miscellaneous configurable options - * - */ -#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ - -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_info (bd_t) */ -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * watchdog configuration - * - */ -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * UART configuration - * - */ -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() - -#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* use internal serial clock */ -#define CONFIG_SYS_BASE_BAUD 691200 -#define CONFIG_BAUDRATE 38400 /* Default baud rate */ -#define CONFIG_SYS_BAUDRATE_TABLE \ - { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400 } - -/* - * I2C configuration - * - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F /* I2C slave address */ - -/* - * MII PHY configuration - * - */ -#define CONFIG_PPC4xx_EMAC -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 0 /* PHY address */ -#define CONFIG_PHY_CMD_DELAY 40 /* PHY COMMAND delay */ - /* 32usec min. for LXT971A */ -#define CONFIG_PHY_RESET_DELAY 300 /* PHY RESET recovery delay */ - -/* - * RTC configuration - * - * Note that DS1307 RTC is limited to 100Khz I2C bus. - * - */ -#define CONFIG_RTC_DS1307 /* Use Dallas 1307 RTC */ - -/* - * PCI stuff - * - */ -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ -#define CONFIG_PCI_PNP /* do pci plug-and-play */ - /* resource configuration */ -#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ -#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/ - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */ -#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ -#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */ -#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */ -#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ - -/* - * IDE stuff - * - */ -#undef CONFIG_IDE_PCMCIA /* no pcmcia interface required */ -#undef CONFIG_IDE_LED /* no led for ide supported */ -#undef CONFIG_IDE_RESET /* no reset for ide supported */ - -/* - * Environment configuration - * - */ -#define CONFIG_ENV_IS_IN_FLASH 1 /* environment is in FLASH */ -#undef CONFIG_ENV_IS_IN_NVRAM -#undef CONFIG_ENV_IS_IN_EEPROM - -/* - * General Memory organization - * - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xFF800000 -#define CONFIG_SYS_FLASH_SIZE 0x00800000 -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 KB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 KB for malloc() */ - -#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_RAMSTART -#endif - -#if defined(CONFIG_ENV_IS_IN_FLASH) -#define CONFIG_ENV_IN_OWN_SECTOR 1 /* Give Environment own sector */ -#define CONFIG_ENV_ADDR 0xFFF00000 /* Address of Environment Sector */ -#define CONFIG_ENV_SIZE 0x00001000 /* Size of Environment */ -#define CONFIG_ENV_SECT_SIZE 0x00040000 /* Size of Environment Sector */ -#endif - -/* - * FLASH Device configuration - * - */ -#define CONFIG_SYS_FLASH_CFI 1 /* flash is CFI conformant */ -#define CONFIG_FLASH_CFI_DRIVER 1 /* use common cfi driver */ -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max # of memory banks */ -#define CONFIG_SYS_FLASH_INCREMENT 0 /* there is only one bank */ -#define CONFIG_SYS_MAX_FLASH_SECT 64 /* max # of sectors on one chip */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* hardware flash protection */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } - -/* - * On Chip Memory location/size - * - */ -#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 -#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 - -/* - * Global info and initial stack - * - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of on-chip SRAM */ -#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* - * Miscellaneous board specific definitions - * - */ -#define CONFIG_I2CFAST 1 /* enable "i2cfast" env. setting */ - -#endif /* __CONFIG_H */