Hi Neil, + Jerome,
On Sat, 21 Dec 2019 at 00:28, Anand Moon linux.amoon@gmail.com wrote:
Hi Neil,
Could you try the following patches instead of this one ?
https://patchwork.ozlabs.org/patch/1213648/ https://patchwork.ozlabs.org/patch/1213650/
Yes I have tried this series it worked for me. It's much better fix than my approach.
Looks like I did some wrong testing, with microSD card connected, I missed that. For me at this point this issue persist. Here is the logs below.
emmc switch 1 ok 00000000 emmc switch 2 ok fastboot data verify verify result: 255 Cfg max: 1, cur: 1. Board id: 255. Force loop cfg DDR4 probe ddr clk to 1320MHz Load ddrfw from eMMC, src: 0x00014200, des: 0xfffd0000, size: 0x0000c000, part: 0 00000000 emmc switch 0 ok Check phy result INFO : End of initialization INFO : End of read enable training INFO : End of fine write leveling INFO : End of read dq deskew training INFO : End of MPR read delay center optimization INFO : End of Write leveling coarse delay INFO : End of write delay center optimization INFO : End of read delay center optimization INFO : End of max read latency training INFO : Training has run successfully! 1D training succeed Load ddrfw from eMMC, src: 0x00020200, des: 0xfffd0000, size: 0x0000c000, part: 0 Check phy result INFO : End of initialization INFO : End of 2D read delay Voltage center optimization INFO : End of 2D write delay Voltage center optimization INFO : Training has run successfully!
R0_RxClkDly_Margin==82 ps 7 R0_TxDqDly_Margi==106 ps 9
R1_RxClkDly_Margin==0 ps 0 R1_TxDqDly_Margi==0 ps 0
dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0001 2D training succeed auto size-- 65535DDR cs0 size: 2048MB DDR cs1 size: 2048MB DMC_DDR_CTRL: 00600024DDR size: 3928MB cs0 DataBus test pass cs1 DataBus test pass cs0 AddrBus test pass cs1 AddrBus test pass pre test bdlr_100_average==435 bdlr_100_min==435 bdlr_100_max==435 bdlr_100_cur==435 aft test bdlr_100_average==435 bdlr_100_min==435 bdlr_100_max==435 bdlr_100_cur==435 non-sec scramble use zero key ddr scramble enabled
100bdlr_step_size ps== 435 result report boot times 2Enable ddr reg access 00000000 emmc switch 3 ok Authentication key not yet programmed get rpmb counter error 0x00000007 00000000 emmc switch 0 ok Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 0 Load BL3X from eMMC, src: 0x0006c200, des: 0x0175c000, size: 0x00088200, part: 0 0.0;M3 CHK:0;cm4_sp_mode 0 E30HDR MVN_1=0x00000000 MVN_2=0x00000000 [Image: g12b_v1.1.3375-8f9c8a7 2019-01-24 10:44:46 guotai.shen@droid11-sz] OPS=0x40 ring efuse init chipver efuse init 29 0a 40 00 01 20 10 00 00 15 30 32 54 52 4d 50 [3.472682 Inits done] secure task start! high task start! low task start! run into bl31 NOTICE: BL31: v1.3(release):ab8811b NOTICE: BL31: Built : 15:03:31, Feb 12 2019 NOTICE: BL31: G12A normal boot! NOTICE: BL31: BL33 decompress pass ERROR: Error initializing runtime service opteed_fast
U-Boot 2020.01-rc5-00009-g269c6e8c39 (Dec 20 2019 - 15:38:58 +0530) odroid-n2
Model: Hardkernel ODROID-N2 SoC: Amlogic Meson G12B (S922X) Revision 29:a (40:2) DRAM: 3.8 GiB MMC: sd@ffe05000: 0, mmc@ffe07000: 1 In: serial@3000 Out: serial@3000 Err: serial@3000 Net: Warning: ethernet@ff3f0000 (eth0) using random MAC address - 4a:ab:15:ba:29:62 eth0: ethernet@ff3f0000 Hit any key to stop autoboot: 0 Card did not respond to voltage select! unable to select a mode switch to partitions #0, OK mmc1(part 0) is current device ** No partition table - mmc 1 ** MMC Device 2 not found no mmc device at slot 2 starting USB... Bus usb@ff500000: Register 3000140 NbrPorts 3 Starting the controller USB XHCI 1.10 scanning bus usb@ff500000 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found
complete logs in below linked. [0] http://pastebin.com/UsVMYAvW
-Anand