[U-Boot] [PATCH 1/6] firmware: ti_sci: Add support for NAVSS resource management

From: Grygorii Strashko grygorii.strashko@ti.com

Texas Instruments' System Control Interface (TI-SCI) Message Protocol abstracts management of NAVSS resources, like PSI-L pairing and unpairing, UDMAP tx/rx/flow configuration and Rings.

This patch adds support for requesting and configuring such resources from TI-SCI firmware.

Signed-off-by: Peter Ujfalusi peter.ujfalusi@ti.com Signed-off-by: Grygorii Strashko grygorii.strashko@ti.com --- drivers/firmware/ti_sci.c | 424 +++++++++++++++++ drivers/firmware/ti_sci.h | 600 +++++++++++++++++++++++++ include/linux/soc/ti/ti_sci_protocol.h | 228 ++++++++++ 3 files changed, 1252 insertions(+)

diff --git a/drivers/firmware/ti_sci.c b/drivers/firmware/ti_sci.c index 91481260411a..d12abae41f1c 100644 --- a/drivers/firmware/ti_sci.c +++ b/drivers/firmware/ti_sci.c @@ -12,6 +12,7 @@ #include <errno.h> #include <mailbox.h> #include <dm/device.h> +#include <linux/compat.h> #include <linux/err.h> #include <linux/soc/ti/k3-sec-proxy.h> #include <linux/soc/ti/ti_sci_protocol.h> @@ -1803,6 +1804,416 @@ static int ti_sci_cmd_get_proc_boot_status(const struct ti_sci_handle *handle, return ret; }

+/** + * ti_sci_cmd_ring_config() - configure RA ring + * @handle: pointer to TI SCI handle + * @valid_params: Bitfield defining validity of ring configuration parameters. + * @nav_id: Device ID of Navigator Subsystem from which the ring is allocated + * @index: Ring index. + * @addr_lo: The ring base address lo 32 bits + * @addr_hi: The ring base address hi 32 bits + * @count: Number of ring elements. + * @mode: The mode of the ring + * @size: The ring element size. + * @order_id: Specifies the ring's bus order ID. + * + * Return: 0 if all went well, else returns appropriate error value. + * + * See @ti_sci_msg_rm_ring_cfg_req for more info. + */ +static int ti_sci_cmd_ring_config(const struct ti_sci_handle *handle, + u32 valid_params, u16 nav_id, u16 index, + u32 addr_lo, u32 addr_hi, u32 count, + u8 mode, u8 size, u8 order_id) +{ + struct ti_sci_msg_rm_ring_cfg_resp *resp; + struct ti_sci_msg_rm_ring_cfg_req req; + struct ti_sci_xfer *xfer; + struct ti_sci_info *info; + int ret = 0; + + if (IS_ERR(handle)) + return PTR_ERR(handle); + if (!handle) + return -EINVAL; + + info = handle_to_ti_sci_info(handle); + + xfer = ti_sci_setup_one_xfer(info, TI_SCI_MSG_RM_RING_CFG, + TI_SCI_FLAG_REQ_ACK_ON_PROCESSED, + (u32 *)&req, sizeof(req), sizeof(*resp)); + if (IS_ERR(xfer)) { + ret = PTR_ERR(xfer); + dev_err(info->dev, "RM_RA:Message config failed(%d)\n", ret); + return ret; + } + req.valid_params = valid_params; + req.nav_id = nav_id; + req.index = index; + req.addr_lo = addr_lo; + req.addr_hi = addr_hi; + req.count = count; + req.mode = mode; + req.size = size; + req.order_id = order_id; + + ret = ti_sci_do_xfer(info, xfer); + if (ret) { + dev_err(info->dev, "RM_RA:Mbox config send fail %d\n", ret); + goto fail; + } + + resp = (struct ti_sci_msg_rm_ring_cfg_resp *)xfer->tx_message.buf; + + ret = ti_sci_is_response_ack(resp) ? 0 : -ENODEV; + +fail: + dev_dbg(info->dev, "RM_RA:config ring %u ret:%d\n", index, ret); + return ret; +} + +/** + * ti_sci_cmd_ring_get_config() - get RA ring configuration + * @handle: pointer to TI SCI handle + * @nav_id: Device ID of Navigator Subsystem from which the ring is allocated + * @index: Ring index. + * @addr_lo: returns ring's base address lo 32 bits + * @addr_hi: returns ring's base address hi 32 bits + * @count: returns number of ring elements. + * @mode: returns mode of the ring + * @size: returns ring element size. + * @order_id: returns ring's bus order ID. + * + * Return: 0 if all went well, else returns appropriate error value. + * + * See @ti_sci_msg_rm_ring_get_cfg_req for more info. + */ +static int ti_sci_cmd_ring_get_config(const struct ti_sci_handle *handle, + u32 nav_id, u32 index, u8 *mode, + u32 *addr_lo, u32 *addr_hi, + u32 *count, u8 *size, u8 *order_id) +{ + struct ti_sci_msg_rm_ring_get_cfg_resp *resp; + struct ti_sci_msg_rm_ring_get_cfg_req req; + struct ti_sci_xfer *xfer; + struct ti_sci_info *info; + int ret = 0; + + if (IS_ERR(handle)) + return PTR_ERR(handle); + if (!handle) + return -EINVAL; + + info = handle_to_ti_sci_info(handle); + + xfer = ti_sci_setup_one_xfer(info, TI_SCI_MSG_RM_RING_GET_CFG, + TI_SCI_FLAG_REQ_ACK_ON_PROCESSED, + (u32 *)&req, sizeof(req), sizeof(*resp)); + if (IS_ERR(xfer)) { + ret = PTR_ERR(xfer); + dev_err(info->dev, + "RM_RA:Message get config failed(%d)\n", ret); + return ret; + } + req.nav_id = nav_id; + req.index = index; + + ret = ti_sci_do_xfer(info, xfer); + if (ret) { + dev_err(info->dev, "RM_RA:Mbox get config send fail %d\n", ret); + goto fail; + } + + resp = (struct ti_sci_msg_rm_ring_get_cfg_resp *)xfer->tx_message.buf; + + if (!ti_sci_is_response_ack(resp)) { + ret = -ENODEV; + } else { + if (mode) + *mode = resp->mode; + if (addr_lo) + *addr_lo = resp->addr_lo; + if (addr_hi) + *addr_hi = resp->addr_hi; + if (count) + *count = resp->count; + if (size) + *size = resp->size; + if (order_id) + *order_id = resp->order_id; + }; + +fail: + dev_dbg(info->dev, "RM_RA:get config ring %u ret:%d\n", index, ret); + return ret; +} + +static int ti_sci_cmd_rm_psil_pair(const struct ti_sci_handle *handle, + u32 nav_id, u32 src_thread, u32 dst_thread) +{ + struct ti_sci_msg_hdr *resp; + struct ti_sci_msg_psil_pair req; + struct ti_sci_xfer *xfer; + struct ti_sci_info *info; + int ret = 0; + + if (IS_ERR(handle)) + return PTR_ERR(handle); + if (!handle) + return -EINVAL; + + info = handle_to_ti_sci_info(handle); + + xfer = ti_sci_setup_one_xfer(info, TI_SCI_MSG_RM_PSIL_PAIR, + TI_SCI_FLAG_REQ_ACK_ON_PROCESSED, + (u32 *)&req, sizeof(req), sizeof(*resp)); + if (IS_ERR(xfer)) { + ret = PTR_ERR(xfer); + dev_err(info->dev, "RM_PSIL:Message alloc failed(%d)\n", ret); + return ret; + } + req.nav_id = nav_id; + req.src_thread = src_thread; + req.dst_thread = dst_thread; + + ret = ti_sci_do_xfer(info, xfer); + if (ret) { + dev_err(info->dev, "RM_PSIL:Mbox send fail %d\n", ret); + goto fail; + } + + resp = (struct ti_sci_msg_hdr *)xfer->tx_message.buf; + ret = ti_sci_is_response_ack(resp) ? 0 : -ENODEV; + +fail: + dev_dbg(info->dev, "RM_PSIL: nav: %u link pair %u->%u ret:%u\n", + nav_id, src_thread, dst_thread, ret); + return ret; +} + +static int ti_sci_cmd_rm_psil_unpair(const struct ti_sci_handle *handle, + u32 nav_id, u32 src_thread, u32 dst_thread) +{ + struct ti_sci_msg_hdr *resp; + struct ti_sci_msg_psil_unpair req; + struct ti_sci_xfer *xfer; + struct ti_sci_info *info; + int ret = 0; + + if (IS_ERR(handle)) + return PTR_ERR(handle); + if (!handle) + return -EINVAL; + + info = handle_to_ti_sci_info(handle); + + xfer = ti_sci_setup_one_xfer(info, TI_SCI_MSG_RM_PSIL_UNPAIR, + TI_SCI_FLAG_REQ_ACK_ON_PROCESSED, + (u32 *)&req, sizeof(req), sizeof(*resp)); + if (IS_ERR(xfer)) { + ret = PTR_ERR(xfer); + dev_err(info->dev, "RM_PSIL:Message alloc failed(%d)\n", ret); + return ret; + } + req.nav_id = nav_id; + req.src_thread = src_thread; + req.dst_thread = dst_thread; + + ret = ti_sci_do_xfer(info, xfer); + if (ret) { + dev_err(info->dev, "RM_PSIL:Mbox send fail %d\n", ret); + goto fail; + } + + resp = (struct ti_sci_msg_hdr *)xfer->tx_message.buf; + ret = ti_sci_is_response_ack(resp) ? 0 : -ENODEV; + +fail: + dev_dbg(info->dev, "RM_PSIL: link unpair %u->%u ret:%u\n", + src_thread, dst_thread, ret); + return ret; +} + +static int ti_sci_cmd_rm_udmap_tx_ch_cfg( + const struct ti_sci_handle *handle, + const struct ti_sci_msg_rm_udmap_tx_ch_cfg *params) +{ + struct ti_sci_msg_rm_udmap_tx_ch_cfg_resp *resp; + struct ti_sci_msg_rm_udmap_tx_ch_cfg_req req; + struct ti_sci_xfer *xfer; + struct ti_sci_info *info; + int ret = 0; + + if (IS_ERR(handle)) + return PTR_ERR(handle); + if (!handle) + return -EINVAL; + + info = handle_to_ti_sci_info(handle); + + xfer = ti_sci_setup_one_xfer(info, TISCI_MSG_RM_UDMAP_TX_CH_CFG, + TI_SCI_FLAG_REQ_ACK_ON_PROCESSED, + (u32 *)&req, sizeof(req), sizeof(*resp)); + if (IS_ERR(xfer)) { + ret = PTR_ERR(xfer); + dev_err(info->dev, "Message TX_CH_CFG alloc failed(%d)\n", ret); + return ret; + } + req.valid_params = params->valid_params; + req.nav_id = params->nav_id; + req.index = params->index; + req.tx_pause_on_err = params->tx_pause_on_err; + req.tx_filt_einfo = params->tx_filt_einfo; + req.tx_filt_pswords = params->tx_filt_pswords; + req.tx_atype = params->tx_atype; + req.tx_chan_type = params->tx_chan_type; + req.tx_supr_tdpkt = params->tx_supr_tdpkt; + req.tx_fetch_size = params->tx_fetch_size; + req.tx_credit_count = params->tx_credit_count; + req.txcq_qnum = params->txcq_qnum; + req.tx_priority = params->tx_priority; + req.tx_qos = params->tx_qos; + req.tx_orderid = params->tx_orderid; + req.fdepth = params->fdepth; + req.tx_sched_priority = params->tx_sched_priority; + + ret = ti_sci_do_xfer(info, xfer); + if (ret) { + dev_err(info->dev, "Mbox send TX_CH_CFG fail %d\n", ret); + goto fail; + } + + resp = + (struct ti_sci_msg_rm_udmap_tx_ch_cfg_resp *)xfer->tx_message.buf; + ret = ti_sci_is_response_ack(resp) ? 0 : -EINVAL; + +fail: + dev_dbg(info->dev, "TX_CH_CFG: chn %u ret:%u\n", params->index, ret); + return ret; +} + +static int ti_sci_cmd_rm_udmap_rx_ch_cfg( + const struct ti_sci_handle *handle, + const struct ti_sci_msg_rm_udmap_rx_ch_cfg *params) +{ + struct ti_sci_msg_rm_udmap_rx_ch_cfg_resp *resp; + struct ti_sci_msg_rm_udmap_rx_ch_cfg_req req; + struct ti_sci_xfer *xfer; + struct ti_sci_info *info; + int ret = 0; + + if (IS_ERR(handle)) + return PTR_ERR(handle); + if (!handle) + return -EINVAL; + + info = handle_to_ti_sci_info(handle); + + xfer = ti_sci_setup_one_xfer(info, TISCI_MSG_RM_UDMAP_RX_CH_CFG, + TI_SCI_FLAG_REQ_ACK_ON_PROCESSED, + (u32 *)&req, sizeof(req), sizeof(*resp)); + if (IS_ERR(xfer)) { + ret = PTR_ERR(xfer); + dev_err(info->dev, "Message RX_CH_CFG alloc failed(%d)\n", ret); + return ret; + } + + req.valid_params = params->valid_params; + req.nav_id = params->nav_id; + req.index = params->index; + req.rx_fetch_size = params->rx_fetch_size; + req.rxcq_qnum = params->rxcq_qnum; + req.rx_priority = params->rx_priority; + req.rx_qos = params->rx_qos; + req.rx_orderid = params->rx_orderid; + req.rx_sched_priority = params->rx_sched_priority; + req.flowid_start = params->flowid_start; + req.flowid_cnt = params->flowid_cnt; + req.rx_pause_on_err = params->rx_pause_on_err; + req.rx_atype = params->rx_atype; + req.rx_chan_type = params->rx_chan_type; + req.rx_ignore_short = params->rx_ignore_short; + req.rx_ignore_long = params->rx_ignore_long; + + ret = ti_sci_do_xfer(info, xfer); + if (ret) { + dev_err(info->dev, "Mbox send RX_CH_CFG fail %d\n", ret); + goto fail; + } + + resp = + (struct ti_sci_msg_rm_udmap_rx_ch_cfg_resp *)xfer->tx_message.buf; + ret = ti_sci_is_response_ack(resp) ? 0 : -EINVAL; + +fail: + dev_dbg(info->dev, "RX_CH_CFG: chn %u ret:%d\n", params->index, ret); + return ret; +} + +static int ti_sci_cmd_rm_udmap_rx_flow_cfg( + const struct ti_sci_handle *handle, + const struct ti_sci_msg_rm_udmap_flow_cfg *params) +{ + struct ti_sci_msg_rm_udmap_flow_cfg_resp *resp; + struct ti_sci_msg_rm_udmap_flow_cfg_req req; + struct ti_sci_xfer *xfer; + struct ti_sci_info *info; + int ret = 0; + + if (IS_ERR(handle)) + return PTR_ERR(handle); + if (!handle) + return -EINVAL; + + info = handle_to_ti_sci_info(handle); + + xfer = ti_sci_setup_one_xfer(info, TISCI_MSG_RM_UDMAP_FLOW_CFG, + TI_SCI_FLAG_REQ_ACK_ON_PROCESSED, + (u32 *)&req, sizeof(req), sizeof(*resp)); + if (IS_ERR(xfer)) { + ret = PTR_ERR(xfer); + dev_err(dev, "RX_FL_CFG: Message alloc failed(%d)\n", ret); + return ret; + } + + req.valid_params = params->valid_params; + req.nav_id = params->nav_id; + req.flow_index = params->flow_index; + req.rx_einfo_present = params->rx_einfo_present; + req.rx_psinfo_present = params->rx_psinfo_present; + req.rx_error_handling = params->rx_error_handling; + req.rx_desc_type = params->rx_desc_type; + req.rx_sop_offset = params->rx_sop_offset; + req.rx_dest_qnum = params->rx_dest_qnum; + req.rx_src_tag_hi = params->rx_src_tag_hi; + req.rx_src_tag_lo = params->rx_src_tag_lo; + req.rx_dest_tag_hi = params->rx_dest_tag_hi; + req.rx_dest_tag_lo = params->rx_dest_tag_lo; + req.rx_src_tag_hi_sel = params->rx_src_tag_hi_sel; + req.rx_src_tag_lo_sel = params->rx_src_tag_lo_sel; + req.rx_dest_tag_hi_sel = params->rx_dest_tag_hi_sel; + req.rx_dest_tag_lo_sel = params->rx_dest_tag_lo_sel; + req.rx_fdq0_sz0_qnum = params->rx_fdq0_sz0_qnum; + req.rx_fdq1_qnum = params->rx_fdq1_qnum; + req.rx_fdq2_qnum = params->rx_fdq2_qnum; + req.rx_fdq3_qnum = params->rx_fdq3_qnum; + req.rx_ps_location = params->rx_ps_location; + + ret = ti_sci_do_xfer(info, xfer); + if (ret) { + dev_err(dev, "RX_FL_CFG: Mbox send fail %d\n", ret); + goto fail; + } + + resp = + (struct ti_sci_msg_rm_udmap_flow_cfg_resp *)xfer->tx_message.buf; + ret = ti_sci_is_response_ack(resp) ? 0 : -EINVAL; + +fail: + dev_dbg(info->dev, "RX_FL_CFG: %u ret:%d\n", params->flow_index, ret); + return ret; +} + /* * ti_sci_setup_ops() - Setup the operations structures * @info: pointer to TISCI pointer @@ -1815,6 +2226,9 @@ static void ti_sci_setup_ops(struct ti_sci_info *info) struct ti_sci_clk_ops *cops = &ops->clk_ops; struct ti_sci_core_ops *core_ops = &ops->core_ops; struct ti_sci_proc_ops *pops = &ops->proc_ops; + struct ti_sci_rm_ringacc_ops *rops = &ops->rm_ring_ops; + struct ti_sci_rm_psil_ops *psilops = &ops->rm_psil_ops; + struct ti_sci_rm_udmap_ops *udmap_ops = &ops->rm_udmap_ops;

bops->board_config = ti_sci_cmd_set_board_config; bops->board_config_rm = ti_sci_cmd_set_board_config_rm; @@ -1857,6 +2271,16 @@ static void ti_sci_setup_ops(struct ti_sci_info *info) pops->set_proc_boot_ctrl = ti_sci_cmd_set_proc_boot_ctrl; pops->proc_auth_boot_image = ti_sci_cmd_proc_auth_boot_image; pops->get_proc_boot_status = ti_sci_cmd_get_proc_boot_status; + + rops->config = ti_sci_cmd_ring_config; + rops->get_config = ti_sci_cmd_ring_get_config; + + psilops->pair = ti_sci_cmd_rm_psil_pair; + psilops->unpair = ti_sci_cmd_rm_psil_unpair; + + udmap_ops->tx_ch_cfg = ti_sci_cmd_rm_udmap_tx_ch_cfg; + udmap_ops->rx_ch_cfg = ti_sci_cmd_rm_udmap_rx_ch_cfg; + udmap_ops->rx_flow_cfg = ti_sci_cmd_rm_udmap_rx_flow_cfg; }

/** diff --git a/drivers/firmware/ti_sci.h b/drivers/firmware/ti_sci.h index 81591fb0c71f..852302b75237 100644 --- a/drivers/firmware/ti_sci.h +++ b/drivers/firmware/ti_sci.h @@ -50,6 +50,31 @@ #define TISCI_MSG_PROC_AUTH_BOOT_IMIAGE 0xc120 #define TISCI_MSG_GET_PROC_BOOT_STATUS 0xc400

+/* NAVSS resource management */ +/* Ringacc requests */ +#define TI_SCI_MSG_RM_RING_CFG 0x1110 +#define TI_SCI_MSG_RM_RING_GET_CFG 0x1111 + +/* PSI-L requests */ +#define TI_SCI_MSG_RM_PSIL_PAIR 0x1280 +#define TI_SCI_MSG_RM_PSIL_UNPAIR 0x1281 + +#define TI_SCI_MSG_RM_UDMAP_TX_ALLOC 0x1200 +#define TI_SCI_MSG_RM_UDMAP_TX_FREE 0x1201 +#define TI_SCI_MSG_RM_UDMAP_RX_ALLOC 0x1210 +#define TI_SCI_MSG_RM_UDMAP_RX_FREE 0x1211 +#define TI_SCI_MSG_RM_UDMAP_FLOW_CFG 0x1220 +#define TI_SCI_MSG_RM_UDMAP_OPT_FLOW_CFG 0x1221 + +#define TISCI_MSG_RM_UDMAP_TX_CH_CFG 0x1205 +#define TISCI_MSG_RM_UDMAP_TX_CH_GET_CFG 0x1206 +#define TISCI_MSG_RM_UDMAP_RX_CH_CFG 0x1215 +#define TISCI_MSG_RM_UDMAP_RX_CH_GET_CFG 0x1216 +#define TISCI_MSG_RM_UDMAP_FLOW_CFG 0x1230 +#define TISCI_MSG_RM_UDMAP_FLOW_SIZE_THRESH_CFG 0x1231 +#define TISCI_MSG_RM_UDMAP_FLOW_GET_CFG 0x1232 +#define TISCI_MSG_RM_UDMAP_FLOW_SIZE_THRESH_GET_CFG 0x1233 + /** * struct ti_sci_msg_hdr - Generic Message Header for All messages and responses * @type: Type of messages: One of TI_SCI_MSG* values @@ -677,4 +702,579 @@ struct ti_sci_msg_resp_get_proc_boot_status { u32 status_flags; } __packed;

+/** + * struct ti_sci_msg_rm_ring_cfg_req - Configure a Navigator Subsystem ring + * + * Configures the non-real-time registers of a Navigator Subsystem ring. + * @hdr: Generic Header + * @valid_params: Bitfield defining validity of ring configuration parameters. + * The ring configuration fields are not valid, and will not be used for + * ring configuration, if their corresponding valid bit is zero. + * Valid bit usage: + * 0 - Valid bit for @tisci_msg_rm_ring_cfg_req addr_lo + * 1 - Valid bit for @tisci_msg_rm_ring_cfg_req addr_hi + * 2 - Valid bit for @tisci_msg_rm_ring_cfg_req count + * 3 - Valid bit for @tisci_msg_rm_ring_cfg_req mode + * 4 - Valid bit for @tisci_msg_rm_ring_cfg_req size + * 5 - Valid bit for @tisci_msg_rm_ring_cfg_req order_id + * @nav_id: Device ID of Navigator Subsystem from which the ring is allocated + * @index: ring index to be configured. + * @addr_lo: 32 LSBs of ring base address to be programmed into the ring's + * RING_BA_LO register + * @addr_hi: 16 MSBs of ring base address to be programmed into the ring's + * RING_BA_HI register. + * @count: Number of ring elements. Must be even if mode is CREDENTIALS or QM + * modes. + * @mode: Specifies the mode the ring is to be configured. + * @size: Specifies encoded ring element size. To calculate the encoded size use + * the formula (log2(size_bytes) - 2), where size_bytes cannot be + * greater than 256. + * @order_id: Specifies the ring's bus order ID. + */ +struct ti_sci_msg_rm_ring_cfg_req { + struct ti_sci_msg_hdr hdr; + u32 valid_params; + u16 nav_id; + u16 index; + u32 addr_lo; + u32 addr_hi; + u32 count; + u8 mode; + u8 size; + u8 order_id; +} __packed; + +/** + * struct ti_sci_msg_rm_ring_cfg_resp - Response to configuring a ring. + * + * @hdr: Generic Header + */ +struct ti_sci_msg_rm_ring_cfg_resp { + struct ti_sci_msg_hdr hdr; +} __packed; + +/** + * struct ti_sci_msg_rm_ring_get_cfg_req - Get RA ring's configuration + * + * Gets the configuration of the non-real-time register fields of a ring. The + * host, or a supervisor of the host, who owns the ring must be the requesting + * host. The values of the non-real-time registers are returned in + * @ti_sci_msg_rm_ring_get_cfg_resp. + * + * @hdr: Generic Header + * @nav_id: Device ID of Navigator Subsystem from which the ring is allocated + * @index: ring index. + */ +struct ti_sci_msg_rm_ring_get_cfg_req { + struct ti_sci_msg_hdr hdr; + u16 nav_id; + u16 index; +} __packed; + +/** + * struct ti_sci_msg_rm_ring_get_cfg_resp - Ring get configuration response + * + * Response received by host processor after RM has handled + * @ti_sci_msg_rm_ring_get_cfg_req. The response contains the ring's + * non-real-time register values. + * + * @hdr: Generic Header + * @addr_lo: Ring 32 LSBs of base address + * @addr_hi: Ring 16 MSBs of base address. + * @count: Ring number of elements. + * @mode: Ring mode. + * @size: encoded Ring element size + * @order_id: ing order ID. + */ +struct ti_sci_msg_rm_ring_get_cfg_resp { + struct ti_sci_msg_hdr hdr; + u32 addr_lo; + u32 addr_hi; + u32 count; + u8 mode; + u8 size; + u8 order_id; +} __packed; + +/** + * struct ti_sci_msg_psil_pair - Pairs a PSI-L source thread to a destination + * thread + * @hdr: Generic Header + * @nav_id: SoC Navigator Subsystem device ID whose PSI-L config proxy is + * used to pair the source and destination threads. + * @src_thread: PSI-L source thread ID within the PSI-L System thread map. + * + * UDMAP transmit channels mapped to source threads will have their + * TCHAN_THRD_ID register programmed with the destination thread if the pairing + * is successful. + + * @dst_thread: PSI-L destination thread ID within the PSI-L System thread map. + * PSI-L destination threads start at index 0x8000. The request is NACK'd if + * the destination thread is not greater than or equal to 0x8000. + * + * UDMAP receive channels mapped to destination threads will have their + * RCHAN_THRD_ID register programmed with the source thread if the pairing + * is successful. + * + * Request type is TI_SCI_MSG_RM_PSIL_PAIR, response is a generic ACK or NACK + * message. + */ +struct ti_sci_msg_psil_pair { + struct ti_sci_msg_hdr hdr; + u32 nav_id; + u32 src_thread; + u32 dst_thread; +} __packed; + +/** + * struct ti_sci_msg_psil_unpair - Unpairs a PSI-L source thread from a + * destination thread + * @hdr: Generic Header + * @nav_id: SoC Navigator Subsystem device ID whose PSI-L config proxy is + * used to unpair the source and destination threads. + * @src_thread: PSI-L source thread ID within the PSI-L System thread map. + * + * UDMAP transmit channels mapped to source threads will have their + * TCHAN_THRD_ID register cleared if the unpairing is successful. + * + * @dst_thread: PSI-L destination thread ID within the PSI-L System thread map. + * PSI-L destination threads start at index 0x8000. The request is NACK'd if + * the destination thread is not greater than or equal to 0x8000. + * + * UDMAP receive channels mapped to destination threads will have their + * RCHAN_THRD_ID register cleared if the unpairing is successful. + * + * Request type is TI_SCI_MSG_RM_PSIL_UNPAIR, response is a generic ACK or NACK + * message. + */ +struct ti_sci_msg_psil_unpair { + struct ti_sci_msg_hdr hdr; + u32 nav_id; + u32 src_thread; + u32 dst_thread; +} __packed; + +/** + * Configures a Navigator Subsystem UDMAP transmit channel + * + * Configures the non-real-time registers of a Navigator Subsystem UDMAP + * transmit channel. The channel index must be assigned to the host defined + * in the TISCI header via the RM board configuration resource assignment + * range list. + * + * @hdr: Generic Header + * + * @valid_params: Bitfield defining validity of tx channel configuration + * parameters. The tx channel configuration fields are not valid, and will not + * be used for ch configuration, if their corresponding valid bit is zero. + * Valid bit usage: + * 0 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_pause_on_err + * 1 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_atype + * 2 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_chan_type + * 3 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_fetch_size + * 4 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::txcq_qnum + * 5 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_priority + * 6 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_qos + * 7 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_orderid + * 8 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_sched_priority + * 9 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_filt_einfo + * 10 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_filt_pswords + * 11 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_supr_tdpkt + * 12 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_credit_count + * 13 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::fdepth + * + * @nav_id: SoC device ID of Navigator Subsystem where tx channel is located + * + * @index: UDMAP transmit channel index. + * + * @tx_pause_on_err: UDMAP transmit channel pause on error configuration to + * be programmed into the tx_pause_on_err field of the channel's TCHAN_TCFG + * register. + * + * @tx_filt_einfo: UDMAP transmit channel extended packet information passing + * configuration to be programmed into the tx_filt_einfo field of the + * channel's TCHAN_TCFG register. + * + * @tx_filt_pswords: UDMAP transmit channel protocol specific word passing + * configuration to be programmed into the tx_filt_pswords field of the + * channel's TCHAN_TCFG register. + * + * @tx_atype: UDMAP transmit channel non Ring Accelerator access pointer + * interpretation configuration to be programmed into the tx_atype field of + * the channel's TCHAN_TCFG register. + * + * @tx_chan_type: UDMAP transmit channel functional channel type and work + * passing mechanism configuration to be programmed into the tx_chan_type + * field of the channel's TCHAN_TCFG register. + * + * @tx_supr_tdpkt: UDMAP transmit channel teardown packet generation suppression + * configuration to be programmed into the tx_supr_tdpkt field of the channel's + * TCHAN_TCFG register. + * + * @tx_fetch_size: UDMAP transmit channel number of 32-bit descriptor words to + * fetch configuration to be programmed into the tx_fetch_size field of the + * channel's TCHAN_TCFG register. The user must make sure to set the maximum + * word count that can pass through the channel for any allowed descriptor type. + * + * @tx_credit_count: UDMAP transmit channel transfer request credit count + * configuration to be programmed into the count field of the TCHAN_TCREDIT + * register. Specifies how many credits for complete TRs are available. + * + * @txcq_qnum: UDMAP transmit channel completion queue configuration to be + * programmed into the txcq_qnum field of the TCHAN_TCQ register. The specified + * completion queue must be assigned to the host, or a subordinate of the host, + * requesting configuration of the transmit channel. + * + * @tx_priority: UDMAP transmit channel transmit priority value to be programmed + * into the priority field of the channel's TCHAN_TPRI_CTRL register. + * + * @tx_qos: UDMAP transmit channel transmit qos value to be programmed into the + * qos field of the channel's TCHAN_TPRI_CTRL register. + * + * @tx_orderid: UDMAP transmit channel bus order id value to be programmed into + * the orderid field of the channel's TCHAN_TPRI_CTRL register. + * + * @fdepth: UDMAP transmit channel FIFO depth configuration to be programmed + * into the fdepth field of the TCHAN_TFIFO_DEPTH register. Sets the number of + * Tx FIFO bytes which are allowed to be stored for the channel. Check the UDMAP + * section of the TRM for restrictions regarding this parameter. + * + * @tx_sched_priority: UDMAP transmit channel tx scheduling priority + * configuration to be programmed into the priority field of the channel's + * TCHAN_TST_SCHED register. + */ +struct ti_sci_msg_rm_udmap_tx_ch_cfg_req { + struct ti_sci_msg_hdr hdr; + u32 valid_params; + u16 nav_id; + u16 index; + u8 tx_pause_on_err; + u8 tx_filt_einfo; + u8 tx_filt_pswords; + u8 tx_atype; + u8 tx_chan_type; + u8 tx_supr_tdpkt; + u16 tx_fetch_size; + u8 tx_credit_count; + u16 txcq_qnum; + u8 tx_priority; + u8 tx_qos; + u8 tx_orderid; + u16 fdepth; + u8 tx_sched_priority; +} __packed; + +/** + * Response to configuring a UDMAP transmit channel. + * + * @hdr: Standard TISCI header + */ +struct ti_sci_msg_rm_udmap_tx_ch_cfg_resp { + struct ti_sci_msg_hdr hdr; +} __packed; + +/** + * Configures a Navigator Subsystem UDMAP receive channel + * + * Configures the non-real-time registers of a Navigator Subsystem UDMAP + * receive channel. The channel index must be assigned to the host defined + * in the TISCI header via the RM board configuration resource assignment + * range list. + * + * @hdr: Generic Header + * + * @valid_params: Bitfield defining validity of rx channel configuration + * parameters. + * The rx channel configuration fields are not valid, and will not be used for + * ch configuration, if their corresponding valid bit is zero. + * Valid bit usage: + * 0 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_pause_on_err + * 1 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_atype + * 2 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_chan_type + * 3 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_fetch_size + * 4 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rxcq_qnum + * 5 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_priority + * 6 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_qos + * 7 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_orderid + * 8 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_sched_priority + * 9 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::flowid_start + * 10 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::flowid_cnt + * 11 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_ignore_short + * 12 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_ignore_long + * + * @nav_id: SoC device ID of Navigator Subsystem where rx channel is located + * + * @index: UDMAP receive channel index. + * + * @rx_fetch_size: UDMAP receive channel number of 32-bit descriptor words to + * fetch configuration to be programmed into the rx_fetch_size field of the + * channel's RCHAN_RCFG register. + * + * @rxcq_qnum: UDMAP receive channel completion queue configuration to be + * programmed into the rxcq_qnum field of the RCHAN_RCQ register. + * The specified completion queue must be assigned to the host, or a subordinate + * of the host, requesting configuration of the receive channel. + * + * @rx_priority: UDMAP receive channel receive priority value to be programmed + * into the priority field of the channel's RCHAN_RPRI_CTRL register. + * + * @rx_qos: UDMAP receive channel receive qos value to be programmed into the + * qos field of the channel's RCHAN_RPRI_CTRL register. + * + * @rx_orderid: UDMAP receive channel bus order id value to be programmed into + * the orderid field of the channel's RCHAN_RPRI_CTRL register. + * + * @rx_sched_priority: UDMAP receive channel rx scheduling priority + * configuration to be programmed into the priority field of the channel's + * RCHAN_RST_SCHED register. + * + * @flowid_start: UDMAP receive channel additional flows starting index + * configuration to program into the flow_start field of the RCHAN_RFLOW_RNG + * register. Specifies the starting index for flow IDs the receive channel is to + * make use of beyond the default flow. flowid_start and @ref flowid_cnt must be + * set as valid and configured together. The starting flow ID set by + * @ref flowid_cnt must be a flow index within the Navigator Subsystem's subset + * of flows beyond the default flows statically mapped to receive channels. + * The additional flows must be assigned to the host, or a subordinate of the + * host, requesting configuration of the receive channel. + * + * @flowid_cnt: UDMAP receive channel additional flows count configuration to + * program into the flowid_cnt field of the RCHAN_RFLOW_RNG register. + * This field specifies how many flow IDs are in the additional contiguous range + * of legal flow IDs for the channel. @ref flowid_start and flowid_cnt must be + * set as valid and configured together. Disabling the valid_params field bit + * for flowid_cnt indicates no flow IDs other than the default are to be + * allocated and used by the receive channel. @ref flowid_start plus flowid_cnt + * cannot be greater than the number of receive flows in the receive channel's + * Navigator Subsystem. The additional flows must be assigned to the host, or a + * subordinate of the host, requesting configuration of the receive channel. + * + * @rx_pause_on_err: UDMAP receive channel pause on error configuration to be + * programmed into the rx_pause_on_err field of the channel's RCHAN_RCFG + * register. + * + * @rx_atype: UDMAP receive channel non Ring Accelerator access pointer + * interpretation configuration to be programmed into the rx_atype field of the + * channel's RCHAN_RCFG register. + * + * @rx_chan_type: UDMAP receive channel functional channel type and work passing + * mechanism configuration to be programmed into the rx_chan_type field of the + * channel's RCHAN_RCFG register. + * + * @rx_ignore_short: UDMAP receive channel short packet treatment configuration + * to be programmed into the rx_ignore_short field of the RCHAN_RCFG register. + * + * @rx_ignore_long: UDMAP receive channel long packet treatment configuration to + * be programmed into the rx_ignore_long field of the RCHAN_RCFG register. + */ +struct ti_sci_msg_rm_udmap_rx_ch_cfg_req { + struct ti_sci_msg_hdr hdr; + u32 valid_params; + u16 nav_id; + u16 index; + u16 rx_fetch_size; + u16 rxcq_qnum; + u8 rx_priority; + u8 rx_qos; + u8 rx_orderid; + u8 rx_sched_priority; + u16 flowid_start; + u16 flowid_cnt; + u8 rx_pause_on_err; + u8 rx_atype; + u8 rx_chan_type; + u8 rx_ignore_short; + u8 rx_ignore_long; +} __packed; + +/** + * Response to configuring a UDMAP receive channel. + * + * @hdr: Standard TISCI header + */ +struct ti_sci_msg_rm_udmap_rx_ch_cfg_resp { + struct ti_sci_msg_hdr hdr; +} __packed; + +/** + * Configures a Navigator Subsystem UDMAP receive flow + * + * Configures a Navigator Subsystem UDMAP receive flow's registers. + * Configuration does not include the flow registers which handle size-based + * free descriptor queue routing. + * + * The flow index must be assigned to the host defined in the TISCI header via + * the RM board configuration resource assignment range list. + * + * @hdr: Standard TISCI header + * + * @valid_params + * Bitfield defining validity of rx flow configuration parameters. The + * rx flow configuration fields are not valid, and will not be used for flow + * configuration, if their corresponding valid bit is zero. Valid bit usage: + * 0 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_einfo_present + * 1 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_psinfo_present + * 2 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_error_handling + * 3 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_desc_type + * 4 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_sop_offset + * 5 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_dest_qnum + * 6 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_src_tag_hi + * 7 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_src_tag_lo + * 8 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_dest_tag_hi + * 9 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_dest_tag_lo + * 10 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_src_tag_hi_sel + * 11 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_src_tag_lo_sel + * 12 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_dest_tag_hi_sel + * 13 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_dest_tag_lo_sel + * 14 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_fdq0_sz0_qnum + * 15 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_fdq1_sz0_qnum + * 16 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_fdq2_sz0_qnum + * 17 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_fdq3_sz0_qnum + * 18 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_ps_location + * + * @nav_id: SoC device ID of Navigator Subsystem from which the receive flow is + * allocated + * + * @flow_index: UDMAP receive flow index for non-optional configuration. + * + * @rx_einfo_present: + * UDMAP receive flow extended packet info present configuration to be + * programmed into the rx_einfo_present field of the flow's RFLOW_RFA register. + * + * @rx_psinfo_present: + * UDMAP receive flow PS words present configuration to be programmed into the + * rx_psinfo_present field of the flow's RFLOW_RFA register. + * + * @rx_error_handling: + * UDMAP receive flow error handling configuration to be programmed into the + * rx_error_handling field of the flow's RFLOW_RFA register. + * + * @rx_desc_type: + * UDMAP receive flow descriptor type configuration to be programmed into the + * rx_desc_type field field of the flow's RFLOW_RFA register. + * + * @rx_sop_offset: + * UDMAP receive flow start of packet offset configuration to be programmed + * into the rx_sop_offset field of the RFLOW_RFA register. See the UDMAP + * section of the TRM for more information on this setting. Valid values for + * this field are 0-255 bytes. + * + * @rx_dest_qnum: + * UDMAP receive flow destination queue configuration to be programmed into the + * rx_dest_qnum field of the flow's RFLOW_RFA register. The specified + * destination queue must be valid within the Navigator Subsystem and must be + * owned by the host, or a subordinate of the host, requesting allocation and + * configuration of the receive flow. + * + * @rx_src_tag_hi: + * UDMAP receive flow source tag high byte constant configuration to be + * programmed into the rx_src_tag_hi field of the flow's RFLOW_RFB register. + * See the UDMAP section of the TRM for more information on this setting. + * + * @rx_src_tag_lo: + * UDMAP receive flow source tag low byte constant configuration to be + * programmed into the rx_src_tag_lo field of the flow's RFLOW_RFB register. + * See the UDMAP section of the TRM for more information on this setting. + * + * @rx_dest_tag_hi: + * UDMAP receive flow destination tag high byte constant configuration to be + * programmed into the rx_dest_tag_hi field of the flow's RFLOW_RFB register. + * See the UDMAP section of the TRM for more information on this setting. + * + * @rx_dest_tag_lo: + * UDMAP receive flow destination tag low byte constant configuration to be + * programmed into the rx_dest_tag_lo field of the flow's RFLOW_RFB register. + * See the UDMAP section of the TRM for more information on this setting. + * + * @rx_src_tag_hi_sel: + * UDMAP receive flow source tag high byte selector configuration to be + * programmed into the rx_src_tag_hi_sel field of the RFLOW_RFC register. See + * the UDMAP section of the TRM for more information on this setting. + * + * @rx_src_tag_lo_sel: + * UDMAP receive flow source tag low byte selector configuration to be + * programmed into the rx_src_tag_lo_sel field of the RFLOW_RFC register. See + * the UDMAP section of the TRM for more information on this setting. + * + * @rx_dest_tag_hi_sel: + * UDMAP receive flow destination tag high byte selector configuration to be + * programmed into the rx_dest_tag_hi_sel field of the RFLOW_RFC register. See + * the UDMAP section of the TRM for more information on this setting. + * + * @rx_dest_tag_lo_sel: + * UDMAP receive flow destination tag low byte selector configuration to be + * programmed into the rx_dest_tag_lo_sel field of the RFLOW_RFC register. See + * the UDMAP section of the TRM for more information on this setting. + * + * @rx_fdq0_sz0_qnum: + * UDMAP receive flow free descriptor queue 0 configuration to be programmed + * into the rx_fdq0_sz0_qnum field of the flow's RFLOW_RFD register. See the + * UDMAP section of the TRM for more information on this setting. The specified + * free queue must be valid within the Navigator Subsystem and must be owned + * by the host, or a subordinate of the host, requesting allocation and + * configuration of the receive flow. + * + * @rx_fdq1_qnum: + * UDMAP receive flow free descriptor queue 1 configuration to be programmed + * into the rx_fdq1_qnum field of the flow's RFLOW_RFD register. See the + * UDMAP section of the TRM for more information on this setting. The specified + * free queue must be valid within the Navigator Subsystem and must be owned + * by the host, or a subordinate of the host, requesting allocation and + * configuration of the receive flow. + * + * @rx_fdq2_qnum: + * UDMAP receive flow free descriptor queue 2 configuration to be programmed + * into the rx_fdq2_qnum field of the flow's RFLOW_RFE register. See the + * UDMAP section of the TRM for more information on this setting. The specified + * free queue must be valid within the Navigator Subsystem and must be owned + * by the host, or a subordinate of the host, requesting allocation and + * configuration of the receive flow. + * + * @rx_fdq3_qnum: + * UDMAP receive flow free descriptor queue 3 configuration to be programmed + * into the rx_fdq3_qnum field of the flow's RFLOW_RFE register. See the + * UDMAP section of the TRM for more information on this setting. The specified + * free queue must be valid within the Navigator Subsystem and must be owned + * by the host, or a subordinate of the host, requesting allocation and + * configuration of the receive flow. + * + * @rx_ps_location: + * UDMAP receive flow PS words location configuration to be programmed into the + * rx_ps_location field of the flow's RFLOW_RFA register. + */ +struct ti_sci_msg_rm_udmap_flow_cfg_req { + struct ti_sci_msg_hdr hdr; + u32 valid_params; + u16 nav_id; + u16 flow_index; + u8 rx_einfo_present; + u8 rx_psinfo_present; + u8 rx_error_handling; + u8 rx_desc_type; + u16 rx_sop_offset; + u16 rx_dest_qnum; + u8 rx_src_tag_hi; + u8 rx_src_tag_lo; + u8 rx_dest_tag_hi; + u8 rx_dest_tag_lo; + u8 rx_src_tag_hi_sel; + u8 rx_src_tag_lo_sel; + u8 rx_dest_tag_hi_sel; + u8 rx_dest_tag_lo_sel; + u16 rx_fdq0_sz0_qnum; + u16 rx_fdq1_qnum; + u16 rx_fdq2_qnum; + u16 rx_fdq3_qnum; + u8 rx_ps_location; +} __packed; + +/** + * Response to configuring a Navigator Subsystem UDMAP receive flow + * + * @hdr: Standard TISCI header + */ +struct ti_sci_msg_rm_udmap_flow_cfg_resp { + struct ti_sci_msg_hdr hdr; +} __packed; + #endif /* __TI_SCI_H */ diff --git a/include/linux/soc/ti/ti_sci_protocol.h b/include/linux/soc/ti/ti_sci_protocol.h index 90d505363652..081dd7af54dd 100644 --- a/include/linux/soc/ti/ti_sci_protocol.h +++ b/include/linux/soc/ti/ti_sci_protocol.h @@ -257,6 +257,230 @@ struct ti_sci_proc_ops { u32 *sts_flags); };

+#define TI_SCI_RING_MODE_RING (0) +#define TI_SCI_RING_MODE_MESSAGE (1) +#define TI_SCI_RING_MODE_CREDENTIALS (2) +#define TI_SCI_RING_MODE_QM (3) + +#define TI_SCI_MSG_UNUSED_SECONDARY_HOST TI_SCI_RM_NULL_U8 + +/* RA config.addr_lo parameter is valid for RM ring configure TI_SCI message */ +#define TI_SCI_MSG_VALUE_RM_RING_ADDR_LO_VALID BIT(0) +/* RA config.addr_hi parameter is valid for RM ring configure TI_SCI message */ +#define TI_SCI_MSG_VALUE_RM_RING_ADDR_HI_VALID BIT(1) + /* RA config.count parameter is valid for RM ring configure TI_SCI message */ +#define TI_SCI_MSG_VALUE_RM_RING_COUNT_VALID BIT(2) +/* RA config.mode parameter is valid for RM ring configure TI_SCI message */ +#define TI_SCI_MSG_VALUE_RM_RING_MODE_VALID BIT(3) +/* RA config.size parameter is valid for RM ring configure TI_SCI message */ +#define TI_SCI_MSG_VALUE_RM_RING_SIZE_VALID BIT(4) +/* RA config.order_id parameter is valid for RM ring configure TISCI message */ +#define TI_SCI_MSG_VALUE_RM_RING_ORDER_ID_VALID BIT(5) + +#define TI_SCI_MSG_VALUE_RM_ALL_NO_ORDER \ + (TI_SCI_MSG_VALUE_RM_RING_ADDR_LO_VALID | \ + TI_SCI_MSG_VALUE_RM_RING_ADDR_HI_VALID | \ + TI_SCI_MSG_VALUE_RM_RING_COUNT_VALID | \ + TI_SCI_MSG_VALUE_RM_RING_MODE_VALID | \ + TI_SCI_MSG_VALUE_RM_RING_SIZE_VALID) + +/** + * struct ti_sci_rm_ringacc_ops - Ring Accelerator Management operations + * @config: configure the SoC Navigator Subsystem Ring Accelerator ring + * @get_config: get the SoC Navigator Subsystem Ring Accelerator ring + * configuration + */ +struct ti_sci_rm_ringacc_ops { + int (*config)(const struct ti_sci_handle *handle, + u32 valid_params, u16 nav_id, u16 index, + u32 addr_lo, u32 addr_hi, u32 count, u8 mode, + u8 size, u8 order_id + ); + int (*get_config)(const struct ti_sci_handle *handle, + u32 nav_id, u32 index, u8 *mode, + u32 *addr_lo, u32 *addr_hi, u32 *count, + u8 *size, u8 *order_id); +}; + +/** + * struct ti_sci_rm_psil_ops - PSI-L thread operations + * @pair: pair PSI-L source thread to a destination thread. + * If the src_thread is mapped to UDMA tchan, the corresponding channel's + * TCHAN_THRD_ID register is updated. + * If the dst_thread is mapped to UDMA rchan, the corresponding channel's + * RCHAN_THRD_ID register is updated. + * @unpair: unpair PSI-L source thread from a destination thread. + * If the src_thread is mapped to UDMA tchan, the corresponding channel's + * TCHAN_THRD_ID register is cleared. + * If the dst_thread is mapped to UDMA rchan, the corresponding channel's + * RCHAN_THRD_ID register is cleared. + */ +struct ti_sci_rm_psil_ops { + int (*pair)(const struct ti_sci_handle *handle, u32 nav_id, + u32 src_thread, u32 dst_thread); + int (*unpair)(const struct ti_sci_handle *handle, u32 nav_id, + u32 src_thread, u32 dst_thread); +}; + +/* UDMAP channel types */ +#define TI_SCI_RM_UDMAP_CHAN_TYPE_PKT_PBRR 2 +#define TI_SCI_RM_UDMAP_CHAN_TYPE_PKT_PBRR_SB 3 /* RX only */ +#define TI_SCI_RM_UDMAP_CHAN_TYPE_3RDP_PBRR 10 +#define TI_SCI_RM_UDMAP_CHAN_TYPE_3RDP_PBVR 11 +#define TI_SCI_RM_UDMAP_CHAN_TYPE_3RDP_BCOPY_PBRR 12 +#define TI_SCI_RM_UDMAP_CHAN_TYPE_3RDP_BCOPY_PBVR 13 + +/* UDMAP channel atypes */ +#define TI_SCI_RM_UDMAP_ATYPE_PHYS 0 +#define TI_SCI_RM_UDMAP_ATYPE_INTERMEDIATE 1 +#define TI_SCI_RM_UDMAP_ATYPE_VIRTUAL 2 + +/* UDMAP channel scheduling priorities */ +#define TI_SCI_RM_UDMAP_SCHED_PRIOR_HIGH 0 +#define TI_SCI_RM_UDMAP_SCHED_PRIOR_MEDHIGH 1 +#define TI_SCI_RM_UDMAP_SCHED_PRIOR_MEDLOW 2 +#define TI_SCI_RM_UDMAP_SCHED_PRIOR_LOW 3 + +#define TI_SCI_RM_UDMAP_RX_FLOW_DESC_HOST 0 +#define TI_SCI_RM_UDMAP_RX_FLOW_DESC_MONO 2 + +/* UDMAP TX/RX channel valid_params common declarations */ +#define TI_SCI_MSG_VALUE_RM_UDMAP_CH_PAUSE_ON_ERR_VALID BIT(0) +#define TI_SCI_MSG_VALUE_RM_UDMAP_CH_ATYPE_VALID BIT(1) +#define TI_SCI_MSG_VALUE_RM_UDMAP_CH_CHAN_TYPE_VALID BIT(2) +#define TI_SCI_MSG_VALUE_RM_UDMAP_CH_FETCH_SIZE_VALID BIT(3) +#define TI_SCI_MSG_VALUE_RM_UDMAP_CH_CQ_QNUM_VALID BIT(4) +#define TI_SCI_MSG_VALUE_RM_UDMAP_CH_PRIORITY_VALID BIT(5) +#define TI_SCI_MSG_VALUE_RM_UDMAP_CH_QOS_VALID BIT(6) +#define TI_SCI_MSG_VALUE_RM_UDMAP_CH_ORDER_ID_VALID BIT(7) +#define TI_SCI_MSG_VALUE_RM_UDMAP_CH_SCHED_PRIORITY_VALID BIT(8) + +/** + * Configures a Navigator Subsystem UDMAP transmit channel + * + * Configures a Navigator Subsystem UDMAP transmit channel registers. + * See @ti_sci_msg_rm_udmap_tx_ch_cfg_req + */ +struct ti_sci_msg_rm_udmap_tx_ch_cfg { + u32 valid_params; +#define TI_SCI_MSG_VALUE_RM_UDMAP_CH_TX_FILT_EINFO_VALID BIT(9) +#define TI_SCI_MSG_VALUE_RM_UDMAP_CH_TX_FILT_PSWORDS_VALID BIT(10) +#define TI_SCI_MSG_VALUE_RM_UDMAP_CH_TX_SUPR_TDPKT_VALID BIT(11) +#define TI_SCI_MSG_VALUE_RM_UDMAP_CH_TX_CREDIT_COUNT_VALID BIT(12) +#define TI_SCI_MSG_VALUE_RM_UDMAP_CH_TX_FDEPTH_VALID BIT(13) + u16 nav_id; + u16 index; + u8 tx_pause_on_err; + u8 tx_filt_einfo; + u8 tx_filt_pswords; + u8 tx_atype; + u8 tx_chan_type; + u8 tx_supr_tdpkt; + u16 tx_fetch_size; + u8 tx_credit_count; + u16 txcq_qnum; + u8 tx_priority; + u8 tx_qos; + u8 tx_orderid; + u16 fdepth; + u8 tx_sched_priority; +}; + +/** + * Configures a Navigator Subsystem UDMAP receive channel + * + * Configures a Navigator Subsystem UDMAP receive channel registers. + * See @ti_sci_msg_rm_udmap_rx_ch_cfg_req + */ +struct ti_sci_msg_rm_udmap_rx_ch_cfg { + u32 valid_params; +#define TI_SCI_MSG_VALUE_RM_UDMAP_CH_RX_FLOWID_START_VALID BIT(9) +#define TI_SCI_MSG_VALUE_RM_UDMAP_CH_RX_FLOWID_CNT_VALID BIT(10) +#define TI_SCI_MSG_VALUE_RM_UDMAP_CH_RX_IGNORE_SHORT_VALID BIT(11) +#define TI_SCI_MSG_VALUE_RM_UDMAP_CH_RX_IGNORE_LONG_VALID BIT(12) + u16 nav_id; + u16 index; + u16 rx_fetch_size; + u16 rxcq_qnum; + u8 rx_priority; + u8 rx_qos; + u8 rx_orderid; + u8 rx_sched_priority; + u16 flowid_start; + u16 flowid_cnt; + u8 rx_pause_on_err; + u8 rx_atype; + u8 rx_chan_type; + u8 rx_ignore_short; + u8 rx_ignore_long; +}; + +/** + * Configures a Navigator Subsystem UDMAP receive flow + * + * Configures a Navigator Subsystem UDMAP receive flow's registers. + * See @tis_ci_msg_rm_udmap_flow_cfg_req + */ +struct ti_sci_msg_rm_udmap_flow_cfg { + u32 valid_params; +#define TI_SCI_MSG_VALUE_RM_UDMAP_FLOW_EINFO_PRESENT_VALID BIT(0) +#define TI_SCI_MSG_VALUE_RM_UDMAP_FLOW_PSINFO_PRESENT_VALID BIT(1) +#define TI_SCI_MSG_VALUE_RM_UDMAP_FLOW_ERROR_HANDLING_VALID BIT(2) +#define TI_SCI_MSG_VALUE_RM_UDMAP_FLOW_DESC_TYPE_VALID BIT(3) +#define TI_SCI_MSG_VALUE_RM_UDMAP_FLOW_SOP_OFFSET_VALID BIT(4) +#define TI_SCI_MSG_VALUE_RM_UDMAP_FLOW_DEST_QNUM_VALID BIT(5) +#define TI_SCI_MSG_VALUE_RM_UDMAP_FLOW_SRC_TAG_HI_VALID BIT(6) +#define TI_SCI_MSG_VALUE_RM_UDMAP_FLOW_SRC_TAG_LO_VALID BIT(7) +#define TI_SCI_MSG_VALUE_RM_UDMAP_FLOW_DEST_TAG_HI_VALID BIT(8) +#define TI_SCI_MSG_VALUE_RM_UDMAP_FLOW_DEST_TAG_LO_VALID BIT(9) +#define TI_SCI_MSG_VALUE_RM_UDMAP_FLOW_SRC_TAG_HI_SEL_VALID BIT(10) +#define TI_SCI_MSG_VALUE_RM_UDMAP_FLOW_SRC_TAG_LO_SEL_VALID BIT(11) +#define TI_SCI_MSG_VALUE_RM_UDMAP_FLOW_DEST_TAG_HI_SEL_VALID BIT(12) +#define TI_SCI_MSG_VALUE_RM_UDMAP_FLOW_DEST_TAG_LO_SEL_VALID BIT(13) +#define TI_SCI_MSG_VALUE_RM_UDMAP_FLOW_FDQ0_SZ0_QNUM_VALID BIT(14) +#define TI_SCI_MSG_VALUE_RM_UDMAP_FLOW_FDQ1_QNUM_VALID BIT(15) +#define TI_SCI_MSG_VALUE_RM_UDMAP_FLOW_FDQ2_QNUM_VALID BIT(16) +#define TI_SCI_MSG_VALUE_RM_UDMAP_FLOW_FDQ3_QNUM_VALID BIT(17) +#define TI_SCI_MSG_VALUE_RM_UDMAP_FLOW_PS_LOCATION_VALID BIT(18) + u16 nav_id; + u16 flow_index; + u8 rx_einfo_present; + u8 rx_psinfo_present; + u8 rx_error_handling; + u8 rx_desc_type; + u16 rx_sop_offset; + u16 rx_dest_qnum; + u8 rx_src_tag_hi; + u8 rx_src_tag_lo; + u8 rx_dest_tag_hi; + u8 rx_dest_tag_lo; + u8 rx_src_tag_hi_sel; + u8 rx_src_tag_lo_sel; + u8 rx_dest_tag_hi_sel; + u8 rx_dest_tag_lo_sel; + u16 rx_fdq0_sz0_qnum; + u16 rx_fdq1_qnum; + u16 rx_fdq2_qnum; + u16 rx_fdq3_qnum; + u8 rx_ps_location; +}; + +/** + * struct ti_sci_rm_udmap_ops - UDMA Management operations + * @tx_ch_cfg: configure SoC Navigator Subsystem UDMA transmit channel. + * @rx_ch_cfg: configure SoC Navigator Subsystem UDMA receive channel. + * @rx_flow_cfg: configure SoC Navigator Subsystem UDMA receive flow. + */ +struct ti_sci_rm_udmap_ops { + int (*tx_ch_cfg)(const struct ti_sci_handle *handle, + const struct ti_sci_msg_rm_udmap_tx_ch_cfg *params); + int (*rx_ch_cfg)(const struct ti_sci_handle *handle, + const struct ti_sci_msg_rm_udmap_rx_ch_cfg *params); + int (*rx_flow_cfg)( + const struct ti_sci_handle *handle, + const struct ti_sci_msg_rm_udmap_flow_cfg *params); +}; + /** * struct ti_sci_ops - Function support for TI SCI * @board_ops: Miscellaneous operations @@ -264,6 +488,7 @@ struct ti_sci_proc_ops { * @clk_ops: Clock specific operations * @core_ops: Core specific operations * @proc_ops: Processor specific operations + * @ring_ops: Ring Accelerator Management operations */ struct ti_sci_ops { struct ti_sci_board_ops board_ops; @@ -271,6 +496,9 @@ struct ti_sci_ops { struct ti_sci_clk_ops clk_ops; struct ti_sci_core_ops core_ops; struct ti_sci_proc_ops proc_ops; + struct ti_sci_rm_ringacc_ops rm_ring_ops; + struct ti_sci_rm_psil_ops rm_psil_ops; + struct ti_sci_rm_udmap_ops rm_udmap_ops; };

/**