From: Rabeeh Khoury rabeeh@solid-run.com
Added A8040 dts file for community board MACCHIATIBin. The patch includes the following features: AP - Serial console (connected to onboard FTDI usb to serial) CP0 - PCIe x4, SATA, I2C and 10G KR (connected to Marvell 3310 10G copper / SFP+ phy) CP1 - Boot SPI, USB3 host, 2xSATA, 10G KR (connected to Marvell 3310 10G copper / SFP+ phy), SGMII connected to onboard 1512 1Gbps copper phy, and additional SGMII connected to SFP (default 1Gbps can be configured to 2.5Gbps).
Network interface naming - egiga0 - CP0 KR egiga1 - CP1 KR egiga2 - CP1 RJ45 1Gbps connector (recommended for TFTP boot) egiga3 - CP1 SFP default 1Gbps and can be modified to 2.5Gbps
Signed-off-by: Konstantin Porotchkin kostap@marvell.com Signed-off-by: Rabeeh Khoury rabeeh@solid-run.com Cc: Stefan Roese sr@denx.de Cc: Nadav Haklai nadavh@marvell.com Cc: Neta Zur Hershkovits neta@marvell.com Cc: Igal Liberman igall@marvell.com Cc: Haim Boot hayim@marvell.com --- Changes for v3: - Add SD and eMMC entries - Rebase on top of master branch
arch/arm/dts/Makefile | 1 + arch/arm/dts/armada-8040-mcbin.dts | 287 +++++++++++++++++++++++++++++++++++++ 2 files changed, 288 insertions(+) create mode 100644 arch/arm/dts/armada-8040-mcbin.dts
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 397a0ae..a3b139b 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -76,6 +76,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += \ armada-385-amc.dtb \ armada-7040-db.dtb \ armada-8040-db.dtb \ + armada-8040-mcbin.dtb \ armada-xp-gp.dtb \ armada-xp-maxbcm.dtb \ armada-xp-synology-ds414.dtb \ diff --git a/arch/arm/dts/armada-8040-mcbin.dts b/arch/arm/dts/armada-8040-mcbin.dts new file mode 100644 index 0000000..15da53d --- /dev/null +++ b/arch/arm/dts/armada-8040-mcbin.dts @@ -0,0 +1,287 @@ +/* + * Copyright (C) 2016 Marvell International Ltd. + * + * SPDX-License-Identifier: GPL-2.0 + * https://spdx.org/licenses + */ + +#include "armada-8040.dtsi" /* include SoC device tree */ + +/ { + model = "MACCHIATOBin-8040"; + compatible = "marvell,armada8040-mcbin", + "marvell,armada8040"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + aliases { + i2c0 = &cpm_i2c0; + i2c1 = &cpm_i2c1; + spi0 = &cps_spi1; + gpio0 = &ap_gpio0; + gpio1 = &cpm_gpio0; + gpio2 = &cpm_gpio1; + }; + + memory@00000000 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + +reg_usb3h0_vbus: usb3-vbus0 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&cpm_xhci_vbus_pins>; + regulator-name = "reg-usb3h0-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + startup-delay-us = <500000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&cpm_gpio1 15 GPIO_ACTIVE_HIGH>; /* GPIO[47] */ + }; +}; + +/* Accessible over the mini-USB CON9 connector on the main board */ +&uart0 { + status = "okay"; +}; + +&ap_pinctl { + /* + * MPP Bus: + * eMMC [0-10] + * UART0 [11,19] + */ + /* 0 1 2 3 4 5 6 7 8 9 */ + pin-func = < 1 1 1 1 1 1 1 1 1 1 + 1 3 0 0 0 0 0 0 0 3 >; +}; + +/* on-board eMMC */ +&ap_sdhci0 { + pinctrl-names = "default"; + pinctrl-0 = <&ap_emmc_pins>; + bus-width= <8>; + status = "okay"; +}; + +&cpm_pinctl { + /* + * MPP Bus: + * [0-31] = 0xff: Keep default CP0_shared_pins: + * [11] CLKOUT_MPP_11 (out) + * [23] LINK_RD_IN_CP2CP (in) + * [25] CLKOUT_MPP_25 (out) + * [29] AVS_FB_IN_CP2CP (in) + * [32,34] SMI + * [33] MSS power down + * [35-38] CP0 I2C1 and I2C0 + * [39] MSS CKE Enable + * [40,41] CP0 UART1 TX/RX + * [42,43] XSMI (controls two 10G phys) + * [47] USB VBUS EN + * [48] FAN PWM + * [49] 10G port 1 interrupt + * [50] 10G port 0 interrupt + * [51] 2.5G SFP TX fault + * [52] PCIe reset out + * [53] 2.5G SFP mode + * [54] 2.5G SFP LOS + * [55] Micro SD card detect + * [56-61] Micro SD + * [62] CP1 KR SFP FAULT + */ + /* 0 1 2 3 4 5 6 7 8 9 */ + pin-func = < 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff + 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff + 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff + 0xff 0 7 0xa 7 2 2 2 2 0xa + 7 7 8 8 0 0 0 0 0 0 + 0 0 0 0 0 0 0xe 0xe 0xe 0xe + 0xe 0xe 0 >; + + cpm_xhci_vbus_pins: cpm-xhci-vbus-pins { + marvell,pins = < 47 >; + marvell,function = <0>; + }; + + cpm_pcie_reset_pins: cpm-pcie-reset-pins { + marvell,pins = < 52 >; + marvell,function = <0>; + }; +}; + +/* uSD slot */ +&cpm_sdhci0 { + pinctrl-names = "default"; + pinctrl-0 = <&cpm_sdhci_pins>; + bus-width= <4>; + status = "okay"; +}; + +/* PCIe x4 */ +&cpm_pcie0 { + num-lanes = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&cpm_pcie_reset_pins>; + marvell,reset-gpio = <&cpm_gpio1 20 GPIO_ACTIVE_HIGH>; /* GPIO[52] */ + status = "okay"; +}; + +&cpm_i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&cpm_i2c0_pins>; + status = "okay"; + clock-frequency = <100000>; +}; + +&cpm_i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&cpm_i2c1_pins>; + status = "okay"; + clock-frequency = <100000>; +}; + +&cpm_sata0 { + status = "okay"; +}; + +&cpm_comphy { + /* + * CP0 Serdes Configuration: + * Lane 0: PCIe0 (x4) + * Lane 1: PCIe0 (x4) + * Lane 2: PCIe0 (x4) + * Lane 3: PCIe0 (x4) + * Lane 4: KR (10G) + * Lane 5: SATA1 + */ + phy0 { + phy-type = <PHY_TYPE_PEX0>; + }; + phy1 { + phy-type = <PHY_TYPE_PEX0>; + }; + phy2 { + phy-type = <PHY_TYPE_PEX0>; + }; + phy3 { + phy-type = <PHY_TYPE_PEX0>; + }; + phy4 { + phy-type = <PHY_TYPE_KR>; + }; + phy5 { + phy-type = <PHY_TYPE_SATA1>; + }; +}; + +&cps_sata0 { + status = "okay"; +}; + +&cps_usb3_0 { + vbus-supply = <®_usb3h0_vbus>; + status = "okay"; +}; + +&cps_utmi0 { + status = "okay"; +}; + +&cps_pinctl { + /* + * MPP Bus: + * [0-5] TDM + * [6,7] CP1_UART 0 + * [8] CP1 10G SFP LOS + * [9] CP1 10G PHY RESET + * [10] CP1 10G SFP TX Disable + * [11] CP1 10G SFP Mode + * [12] SPI1 CS1n + * [13] SPI1 MISO (TDM and SPI ROM shared) + * [14] SPI1 CS0n + * [15] SPI1 MOSI (TDM and SPI ROM shared) + * [16] SPI1 CLK (TDM and SPI ROM shared) + * [24] CP1 2.5G SFP TX Disable + * [26] CP0 10G SFP TX Fault + * [27] CP0 10G SFP Mode + * [28] CP0 10G SFP LOS + * [29] CP0 10G SFP TX Disable + * [30] USB Over current indication + * [31] 10G Port 0 phy reset + * [32-62] = 0xff: Keep default CP1_shared_pins: + */ + /* 0 1 2 3 4 5 6 7 8 9 */ + pin-func = < 0x4 0x4 0x4 0x4 0x4 0x4 0x8 0x8 0x0 0x0 + 0x0 0x0 0x3 0x3 0x3 0x3 0x3 0xff 0xff 0xff + 0xff 0xff 0xff 0xff 0x0 0xff 0x0 0x0 0x0 0x0 + 0x0 0x0 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff + 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff + 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff + 0xff 0xff 0xff>; +}; + +&cps_spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&cps_spi1_pins>; + status = "okay"; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <10000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "U-Boot"; + reg = <0 0x200000>; + }; + partition@400000 { + label = "Filesystem"; + reg = <0x200000 0xce0000>; + }; + }; + }; +}; + +&cps_comphy { + /* + * CP1 Serdes Configuration: + * Lane 0: SGMII2 + * Lane 1: SATA 0 + * Lane 2: USB HOST 0 + * Lane 3: SATA1 + * Lane 4: KR (10G) + * Lane 5: SGMII3 + */ + phy0 { + phy-type = <PHY_TYPE_SGMII2>; + phy-speed = <PHY_SPEED_1_25G>; + }; + phy1 { + phy-type = <PHY_TYPE_SATA0>; + }; + phy2 { + phy-type = <PHY_TYPE_USB3_HOST0>; + }; + phy3 { + phy-type = <PHY_TYPE_SATA1>; + }; + phy4 { + phy-type = <PHY_TYPE_KR>; + }; + phy5 { + phy-type = <PHY_TYPE_SGMII3>; + }; +};