On 09/06/2016 02:52 PM, Simon Glass wrote:
Hi Alex,
On 6 September 2016 at 03:09, Alexander Graf agraf@suse.de wrote:
On 09/06/2016 03:05 AM, Simon Glass wrote:
Hi Alex,
On 5 September 2016 at 04:51, Alexander Graf agraf@suse.de wrote:
On 08/19/2016 08:45 AM, Michal Simek wrote:
On 16.8.2016 20:39, Alexander Graf wrote:
Hi Michal,
I just tried to run the latest u-boot master + a few patches to implement generic PSCI RTS support on zynqmp and got this:
e U-Boot 2016.09-rc1-00453-ga0592f1 (Aug 16 2016 - 20:27:40 +0200) Xilinx ZynqMP ZCU102
I2C: ready DRAM: 4 GiB EL Level: EL2 MMC: sdhci@ff170000: 0 Using default environment
In: serial@ff000000 Out: serial@ff000000 Err: serial@ff000000 Bootmode: SD_MODE1 SCSI: SATA link 0 timeout. Target spinup took 0 ms. AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x3 impl SATA mode flags: 64bit ncq pm clo only pmp fbss pio slum part ccc apst scanning bus for devices... "Synchronous Abort" handler, esr 0x96000004 ELR: 7ff42d20 LR: 7ff3ff10 x0 : 0000000000000000 x1 : 0000000000000000 x2 : 0000000000000001 x3 : 000000007df1aa80 x4 : aaaaaaaaaaaaaaaa x5 : 0000000000000001 x6 : 0000000000000200 x7 : 0000000000000004 x8 : 000000007ff9f800 x9 : 0000000000000008 x10: 000000007ff9f8f0 x11: 0000000000000000 x12: 00000000ffffffff x13: 00000000ffffffff x14: 000000007ff8242f x15: 000000007ff82435 x16: 000000007ff84388 x17: 000000007ff84388 x18: 000000007df1ade8 x19: 000000007df1aa80 x20: 000000007ff92cb8 x21: 000000007ff9f800 x22: 000000007ff9f000 x23: 0000000000000078 x24: 000000007ff9f8f0 x25: 0000000000000000 x26: 000000007ff9f800 x27: 000000007ff9f000 x28: 000000007ff9fb00 x29: 000000007df1aca0
Resetting CPU ...
resetting …
Is this a known problem?
Is this issue with usb? I have usb off on zcu102 that's why if this usb issue I am not aware about it.
After a bit of digging, turns out it's CONFIG_BLK. If I disable that things work again (albeit without mmc access, since that one requires CONFIG_BLK now).
I don't have a zynqmp device, so cannot test with that unfortunately.
Well, QEMU supports zcu102 emulation in the latest version, so you could use that to emulate the board:
$ qemu-system-aarch64 -M xlnx-zcu102 -kernel u-boot.elf -nographic -m 2G -drive file=u-boot,id=d,if=none -device ide-drive,drive=d,bus=ide.0
However, I don't see the data abort with the emulated device, only with actual hardware. Probably because real hardware is more upset about reading from address 0 ;). But I can provoke the oops even in QEMU if I unmap the first page from the memory map using the patch below.
The oops happens in blk_dread because block_dev->bdev is NULL.
Yes, this field really should be removed. As the comment says it's a hangover from pre-CONFIG_BLK where functions use a struct blk_dev * to specify the block device instead of a struct udevice *. It came up recently on a patch you sent also which is why I am so against using it.
That said, I'm not sure why it is unset. The path should be:
sdhci_bind() mmc_bind() blk_create_devicef() blk_create_device() which sets:
desc->bdev = dev;
[snip]
The special case about ZynqMP is that it has 2 storage backends, one that uses DM (the sdhc controller) and one that isn't converted to DM (the AHCI controller). I guess something goes wrong with the latter.
Alex