Tested-by: Pau Pajuelo ppajuel@gmail.com
2017-08-17 3:06 GMT+02:00 Ladislav Michl ladis@linux-mips.org:
Avoid cluttering board file with CONFIG_SPL_BUILD ifdefs by moving SPL related functions into separate file.
Signed-off-by: Ladislav Michl ladis@linux-mips.org
board/isee/igep00x0/Makefile | 6 +- board/isee/igep00x0/common.c | 80 ++++++++++++++++++++++++++ board/isee/igep00x0/igep00x0.c | 128 ----------------------------------------- board/isee/igep00x0/spl.c | 64 +++++++++++++++++++++ 4 files changed, 149 insertions(+), 129 deletions(-)
diff --git a/board/isee/igep00x0/Makefile b/board/isee/igep00x0/Makefile index 68b151c3c5..74594da771 100644 --- a/board/isee/igep00x0/Makefile +++ b/board/isee/igep00x0/Makefile @@ -5,4 +5,8 @@ # SPDX-License-Identifier: GPL-2.0+ #
-obj-y := igep00x0.o +ifdef CONFIG_SPL_BUILD +obj-y := spl.o common.o +else +obj-y := igep00x0.o common.o +endif diff --git a/board/isee/igep00x0/common.c b/board/isee/igep00x0/common.c new file mode 100644 index 0000000000..b8f1c14f6a --- /dev/null +++ b/board/isee/igep00x0/common.c @@ -0,0 +1,80 @@ +/*
- SPDX-License-Identifier: GPL-2.0+
- */
+#include <common.h> +#include <twl4030.h> +#include <asm/io.h> +#include <asm/omap_mmc.h> +#include <asm/arch/mux.h> +#include <asm/arch/sys_proto.h> +#include <jffs2/load_kernel.h> +#include <linux/mtd/nand.h> +#include "igep00x0.h"
+DECLARE_GLOBAL_DATA_PTR;
+/*
- Routine: set_muxconf_regs
- Description: Setting up the configuration Mux registers specific to the
hardware. Many pins need to be moved from protect to primary
mode.- */
+void set_muxconf_regs(void) +{
MUX_DEFAULT();+#if (CONFIG_MACH_TYPE == MACH_TYPE_IGEP0020)
MUX_IGEP0020();+#endif
+#if (CONFIG_MACH_TYPE == MACH_TYPE_IGEP0030)
MUX_IGEP0030();+#endif +}
+/*
- Routine: board_init
- Description: Early hardware init.
- */
+int board_init(void) +{
int loops = 100;/* find out flash memory type, assume NAND first */gpmc_cs0_flash = MTD_DEV_TYPE_NAND;gpmc_init();/* Issue a RESET and then READID */writeb(NAND_CMD_RESET, &gpmc_cfg->cs[0].nand_cmd);writeb(NAND_CMD_STATUS, &gpmc_cfg->cs[0].nand_cmd);while ((readl(&gpmc_cfg->cs[0].nand_dat) & NAND_STATUS_READY)!= NAND_STATUS_READY) {udelay(1);if (--loops == 0) {gpmc_cs0_flash = MTD_DEV_TYPE_ONENAND;gpmc_init(); /* reinitialize for OneNAND */break;}}/* boot param addr */gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);+#if defined(CONFIG_LED_STATUS) && defined(CONFIG_LED_STATUS_BOOT_ENABLE)
status_led_set(CONFIG_LED_STATUS_BOOT, CONFIG_LED_STATUS_ON);+#endif
return 0;+}
+#if defined(CONFIG_MMC) +int board_mmc_init(bd_t *bis) +{
return omap_mmc_init(0, 0, 0, -1, -1);+}
+void board_mmc_power_init(void) +{
twl4030_power_mmc_init(0);+} +#endif diff --git a/board/isee/igep00x0/igep00x0.c b/board/isee/igep00x0/igep00x0.c index a7a75601dd..74f9bab093 100644 --- a/board/isee/igep00x0/igep00x0.c +++ b/board/isee/igep00x0/igep00x0.c @@ -20,15 +20,12 @@ #include <asm/mach-types.h> #include <linux/mtd/mtd.h> #include <linux/mtd/nand.h> -#include <linux/mtd/nand.h> #include <linux/mtd/onenand.h> #include <jffs2/load_kernel.h> #include <mtd_node.h> #include <fdt_support.h> #include "igep00x0.h"
-DECLARE_GLOBAL_DATA_PTR;
static const struct ns16550_platdata igep_serial = { .base = OMAP34XX_UART3, .reg_shift = 2, @@ -41,98 +38,6 @@ U_BOOT_DEVICE(igep_uart) = { &igep_serial };
-/*
- Routine: board_init
- Description: Early hardware init.
- */
-int board_init(void) -{
int loops = 100;/* find out flash memory type, assume NAND first */gpmc_cs0_flash = MTD_DEV_TYPE_NAND;gpmc_init();/* Issue a RESET and then READID */writeb(NAND_CMD_RESET, &gpmc_cfg->cs[0].nand_cmd);writeb(NAND_CMD_STATUS, &gpmc_cfg->cs[0].nand_cmd);while ((readl(&gpmc_cfg->cs[0].nand_dat) & NAND_STATUS_READY)!= NAND_STATUS_READY) {udelay(1);if (--loops == 0) {gpmc_cs0_flash = MTD_DEV_TYPE_ONENAND;gpmc_init(); /* reinitialize for OneNAND */break;}}/* boot param addr */gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);-#if defined(CONFIG_LED_STATUS) && defined(CONFIG_LED_STATUS_BOOT_ENABLE)
status_led_set(CONFIG_LED_STATUS_BOOT, CONFIG_LED_STATUS_ON);-#endif
return 0;-}
-#ifdef CONFIG_SPL_BUILD -/*
- Routine: get_board_mem_timings
- Description: If we use SPL then there is no x-loader nor config header
- so we have to setup the DDR timings ourself on both banks.
- */
-void get_board_mem_timings(struct board_sdrc_timings *timings) -{
int mfr, id, err = identify_nand_chip(&mfr, &id);timings->mr = MICRON_V_MR_165;if (!err) {switch (mfr) {case NAND_MFR_HYNIX:timings->mcfg = HYNIX_V_MCFG_200(256 << 20);timings->ctrla = HYNIX_V_ACTIMA_200;timings->ctrlb = HYNIX_V_ACTIMB_200;break;case NAND_MFR_MICRON:timings->mcfg = MICRON_V_MCFG_200(256 << 20);timings->ctrla = MICRON_V_ACTIMA_200;timings->ctrlb = MICRON_V_ACTIMB_200;break;default:/* Should not happen... */break;}timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;gpmc_cs0_flash = MTD_DEV_TYPE_NAND;} else {if (get_cpu_family() == CPU_OMAP34XX) {timings->mcfg = NUMONYX_V_MCFG_165(256 << 20);timings->ctrla = NUMONYX_V_ACTIMA_165;timings->ctrlb = NUMONYX_V_ACTIMB_165;timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;} else {timings->mcfg = NUMONYX_V_MCFG_200(256 << 20);timings->ctrla = NUMONYX_V_ACTIMA_200;timings->ctrlb = NUMONYX_V_ACTIMB_200;timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;}gpmc_cs0_flash = MTD_DEV_TYPE_ONENAND;}-}
-#ifdef CONFIG_SPL_OS_BOOT -int spl_start_uboot(void) -{
/* break into full u-boot on 'c' */if (serial_tstc() && serial_getc() == 'c')return 1;return 0;-} -#endif -#endif
int onenand_board_init(struct mtd_info *mtd) { if (gpmc_cs0_flash == MTD_DEV_TYPE_ONENAND) { @@ -199,20 +104,6 @@ int board_eth_init(bd_t *bis) static inline void setup_net_chip(void) {} #endif
-#if defined(CONFIG_MMC) -int board_mmc_init(bd_t *bis) -{
return omap_mmc_init(0, 0, 0, -1, -1);-} -#endif
-#if defined(CONFIG_MMC) -void board_mmc_power_init(void) -{
twl4030_power_mmc_init(0);-} -#endif
#ifdef CONFIG_OF_BOARD_SETUP static int ft_enable_by_compatible(void *blob, char *compat, int enable) { @@ -292,22 +183,3 @@ void board_mtdparts_default(const char **mtdids, const char **mtdparts) *mtdparts = parts; } }
-/*
- Routine: set_muxconf_regs
- Description: Setting up the configuration Mux registers specific to the
hardware. Many pins need to be moved from protect to primary
mode.- */
-void set_muxconf_regs(void) -{
MUX_DEFAULT();-#if (CONFIG_MACH_TYPE == MACH_TYPE_IGEP0020)
MUX_IGEP0020();-#endif
-#if (CONFIG_MACH_TYPE == MACH_TYPE_IGEP0030)
MUX_IGEP0030();-#endif -} diff --git a/board/isee/igep00x0/spl.c b/board/isee/igep00x0/spl.c new file mode 100644 index 0000000000..eb705cbe88 --- /dev/null +++ b/board/isee/igep00x0/spl.c @@ -0,0 +1,64 @@ +/*
- SPDX-License-Identifier: GPL-2.0+
- */
+#include <asm/io.h> +#include <asm/arch/mem.h> +#include <asm/arch/sys_proto.h> +#include <jffs2/load_kernel.h> +#include <linux/mtd/nand.h> +#include "igep00x0.h"
+/*
- Routine: get_board_mem_timings
- Description: If we use SPL then there is no x-loader nor config header
- so we have to setup the DDR timings ourself on both banks.
- */
+void get_board_mem_timings(struct board_sdrc_timings *timings) +{
int mfr, id, err = identify_nand_chip(&mfr, &id);timings->mr = MICRON_V_MR_165;if (!err) {switch (mfr) {case NAND_MFR_HYNIX:timings->mcfg = HYNIX_V_MCFG_200(256 << 20);timings->ctrla = HYNIX_V_ACTIMA_200;timings->ctrlb = HYNIX_V_ACTIMB_200;break;case NAND_MFR_MICRON:timings->mcfg = MICRON_V_MCFG_200(256 << 20);timings->ctrla = MICRON_V_ACTIMA_200;timings->ctrlb = MICRON_V_ACTIMB_200;break;default:/* Should not happen... */break;}timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;gpmc_cs0_flash = MTD_DEV_TYPE_NAND;} else {if (get_cpu_family() == CPU_OMAP34XX) {timings->mcfg = NUMONYX_V_MCFG_165(256 << 20);timings->ctrla = NUMONYX_V_ACTIMA_165;timings->ctrlb = NUMONYX_V_ACTIMB_165;timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;} else {timings->mcfg = NUMONYX_V_MCFG_200(256 << 20);timings->ctrla = NUMONYX_V_ACTIMA_200;timings->ctrlb = NUMONYX_V_ACTIMB_200;timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;}gpmc_cs0_flash = MTD_DEV_TYPE_ONENAND;}+}
+#ifdef CONFIG_SPL_OS_BOOT +int spl_start_uboot(void) +{
/* break into full u-boot on 'c' */if (serial_tstc() && serial_getc() == 'c')return 1;return 0;+}
+#endif
2.11.0