Re: [U-Boot] How to enable USB Mass Storage

26 Oct 2017


      Hi Frank,
...
Hello,
I want to use the ums command to access the SD card of a
A20-OlinuxIno-Lime board via usb-org cable. For that I start the CPU
in FEL mode, download the u-boot-sunxi-with-spl.bin file by sunxi-fel
tool. I do this FEL mode boot for preparation of an Einstein A20
board, which has only an internal MMC. I run on uboot serial console:
First of all - I do not have any experience with Allwiner...
...
=> ums 0 mmc 0                   
UMS: LUN 0, dev 0, hwpart 0, sector 0x0, count 0x1dc000            
Controller uninitialized         
g_dnl_register: failed!, error: -6                                 
g_dnl_register failed
Could you paste output of the console after defining #define DEBUG on
top of drivers/usb/gadget/g_dnl.c ?
It seems like your musb UDC is not initialized in your board
(CONFIG_USB_MUSB_GADGET=y).
Please check if you call it at your board file.
...
It seems that the drivers/usb/musb-new/sunxi.c is not initialized.
The devicetree has a node that should match:
usb@01c13000 {
	compatible = "allwinner,sun4i-a10-musb";
	reg = <0x1c13000 0x400>;
	clocks = <0x2 0x0>;
	interrupts = <0x0 0x26 0x4>;
	interrupt-names = "mc";
	phys = <0x2b 0x0>;
	phy-names = "usb";
	extcon = <0x2b 0x0>;
	allwinner,sram = <0x2c 0x1>;
	status = "okay";
	dr_mode = "otg";
};


My config is:
cat defconfig 
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN7I=y
CONFIG_DRAM_CLK=384
CONFIG_MMC0_CD_PIN="PH1"
CONFIG_I2C1_ENABLE=y
CONFIG_SATAPWR="PC3"
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-olinuxino-lime"
CONFIG_AHCI=y
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
CONFIG_SPL_I2C_SUPPORT=y
# CONFIG_FASTBOOT is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_CMD_USB_MASS_STORAGE=y
# CONFIG_SPL_DOS_PARTITION is not set
# CONFIG_SPL_ISO_PARTITION is not set
# CONFIG_SPL_EFI_PARTITION is not set
CONFIG_ETH_DESIGNWARE=y
CONFIG_SUN7I_GMAC=y
CONFIG_AXP_ALDO3_VOLT=2800
CONFIG_AXP_ALDO4_VOLT=2800
CONFIG_SCSI=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_MUSB_GADGET=y
CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
CONFIG_USB_GADGET_DOWNLOAD=y
# CONFIG_USB_ETHER is not set
Is the ums working for Allwinner CPUs, or is there some further
configuration needed that I have not figured out?
Br,
Frank
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
Best regards,
Lukasz Majewski
--
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd@denx.de